Find Verified Microprocessors Suppliers, Manufacturers and Wholesalers

Includes an 80GB PlayStation 3 console, SIXAXIS controller, MotorStorm, AC power cord, A/V cable, Ethernet cable and USB cable
80GB internal hard drive provides exceptional storage for game saves, media and more
Cell Broadband Engine state-of-the-art microprocessor is more powerful than standard single-core processors, delivering breakthroughs in fidelity and believability
Blu-ray media stores up to five times more data than DVDs, providing a larger canvas for unbelievable graphics and unprecedented interaction; Blu-ray drive also plays Blu-ray movies for a high-definition experience with your favorite films

GVN AVR
DVR-M3H SERIES
FULL AUTOMATIC SERVO DYNAMIC VOLTAGE REGULATOR 1000kVA

GUVEN-IS Voltage regulators are the machines that provide the constant voltage that you need by correcting the falling and rising of the mains voltage in the internal structure.

Our DVR-M3H voltage regulators operate fully automatically for voltage regulation without any user intervention.

Once the regulators are switched on, your mains voltage is continuously measured and the necessary up / down operations are performed automatically, giving your system the constant voltage required for a healthy operation.

Servo regulators consist of variac, servo motor which controls variac, electronic multimeter card which controls this motor and booster transformer.

The start torque can quickly correct even very small voltage changes thanks to the high DC servo motor and the control system that can respond quickly to voltage changes.
When the regulation is completed, the servo motor is de-energized with the aid of the electronic braking circuit. It has high efficiency.

Pollution, parasitic, etc. at output voltage. do not corrupt.
You can safely use any area with regular electricity needs without any problems.

The DVR-M3H Regulator provides the following:
Protection of the user from negative voltages.
Protection of the user and the device from excessive current.
Undisturbed pure sinus voltage regulation.
Long-term overload protection and short-term protection.
AC voltage balancing with extremely high accuracy.
Run smoothly on all loads from 0% to 100%.
Manual transfer to bypass regime without regulating.
Display all values against the probabilities in the bypass regime.
Record mains input voltage limits and load current values.
Static, not gradual, dynamically correct output voltage too quickly without user notice.
When protections are activated, record the number of protection trips and the reason for each parameter separately.
Generation as standard is ± 0.4% (379.87V - 382.6V) stable when the input voltage is within the range of 112.6V ..... 537V.

Noiseless and ecological electric tractor.
Moderate purchase price

In these facilities, Bigà can be used for:
- individual transport of personnel
- control, inspection and security service
- maintenance, cleaning and transport of small packages
- towing with trucks up to 800 kg



GENERAL FEATURES:
- Turning radius: cm. 120
- Length. 140
- Width cm. 85
- Height. 110-130
- Minimum height cm. 5.4
- Weight: Kg 120/140 depending on the type of batteries installed
- fiberglass shell fully recyclable
- tube frame with thick serial number for traceability
- Handlebar adjustable in height
- cover with 3.00-4 tires room air (can puncture tires)
- Headlight and taillight - Safety button "ride-on" - Reverse insertable lever - horn, rear view mirror and the battery charge indicator - Electric motor 24 volt permanent magnet 800 watt - 24 volt 800 watt motor RR 1/10 - Electronic high-frequency MOSFET technology controlled by a microprocessor to recover energy during braking - N. Two 12-volt batteries - Traction tubular plate - 102/157 Ah - Built-in charger or external high frequency and automatic control of the state of charge. - Drive chain high strength pinion - Differential aluminum satellites treated steel - Shaft with grafts and 6 hp - Voltage reducer 24 to 12 volts for lighting system - Brake system: front disc brake, rear differential, brake lever on the left and enhanced engine braking from the calibration of the electronic control. - Blue color.

Electric cart

SPECIFICATIONS:
Dimensions:
Total Length mm 930 Width mm. 650 Height mm. 1070
Floor Length mm 870 Width mm. Ground Clearance 620 mm. 330

Weights:
Total kg including batteries. 77.90
Batteries kg. 13 each. x 2

Motor:
Permanent magnet motor with electric 200 W - rpm 120 - 24 V electro 24VDC 2Nm.

Voltage and batteries:
no Two 12V batteries 32 A C5 sealed gel - series connection, without maintenance.
External charger 24 v - 8 ampere - Electronic microprocessor - Power supply 220 v.


Brakes:
Electric brake block engine, listing in the event of power failure.
braking on deceleration (engine braking) enhanced in the calibration of the parameters of the controller.

Speed and Capacity (performance with the vehicle in perfect working order on flat surface:
Max 5 Km / h + / - 10%
Max 250 kg. terms and 100kg. slope of 15%.
Maximum flow rate is considered with the load distributed uniformly on the floor.

Tires:
2 wheels rubber tires mounted on rims with pneumatic 3.00-4 6-ply roofing.
2 wheels 200x50 diameter core polypropylene gray synthetic rubber ring mounted on swivel mounts.

Frame:
Tubular steel and Fe 37 powder-coated polyester for outdoor Ral 6018

Spare parts and tools for the maintenance and repair:
Original spare parts and tools for maintenance and repair are provided directly to order from Italy Bigà spa.

Sound level values: less than 70 dB (A)

Noiseless and ecological electric vehicole/tractor.

16 Km/h.

Direct use: you get on, drive and stop (movement dynamics). For all employees who move in a range greater than 100 mt. For quick repair service and transport of small-sized components. Average time saving of about 40 to 60 minutes per day.

TECHNICAL FEATURES:
- Turning radius: cm. 120
- Length. 140
- Width cm. 85
- Height. 110-130
- Minimum height from ground cm. 5.4
- Weight: Kg 120/140 depending on the type of batteries installed.
- fiberglass shell fully recyclable
- tube frame with thick serial number for traceability
- Handlebar adjustable in height
- cover tires 3.00-4 with room air (can puncture tires)
- Headlight and taillight
- Safety button "ride-on"
- Reverse insertable lever
- horn, rear view mirror and the battery charge indicator
- Electric motor 24 volt permanent magnet 780 watt
- Electronic high-frequency MOSFET technology controlled by a microprocessor to recover energy during braking
- N. Two 12-volt batteries - lightweight tubular plate traction - 105/125 Ah.
- Built-in charger and automatic battery status.
- Drive chain high strength pinion
- Differential aluminum satellites treated steel
- Shaft couplings with 6 quarries
- Voltage reducer 24 to 12 volt lighting system
- Brake system: front disc brake, rear differential, brake lever on the left and engine braking enhanced by the setting of the electronic control.
- Colors: white, red, green , yellow, blue, black, orange (other colors on request).

Noiseless and ecological electric tractor.


10 Km/h.

-offers two different advantages: it allows to move very quickly and transport up to 300 kg of materials by using a truck designed by us. Speedy, handy in narrow spaces, it spins around with the truck within a 200 cm radius allowing quick access to other departments. Quick repair and maintenance of big- sized and heavy materials (the truck is 120x80 cm with a carrying capacity of 300 kg). Allows to avoid using big and expensive vehicles to move small volumes of goods.

TECHNICAL FEATURES:
- Turning radius: cm. 120
- Length. 140
- Width cm. 85
- Height. 110-130
- Minimum height from ground cm. 5.4
- Weight: Kg 123/143 depending on the type of batteries installed.
- fiberglass shell fully recyclable
- tube frame with thick serial number for traceability
- Handlebar adjustable in height
- cover tires 3.00-4 with room air (can puncture tires)

- Headlight and taillight
- Safety button "ride-on"
- Reverse insertable lever
- horn, rear view mirror and charge indicator battery
24 volt 800 watt electric motor RR 1/10
- 24 volt electric motor permanent magnet 780 watt
- Electronic high-frequency MOSFET technology controlled by a microprocessor to recover energy during braking
- N. 2 Batteries 12 volt - tensile tubular plate - 102/157 Ah.
- Built-in charger or external high frequency and automatic control of the state of charge.
- Traction Chain gear ratio 1/10, 125
- Differential aluminum satellites treated steel
- axle shafts with couplings 6 slot
- Voltage reducer 24 to 12 volt lighting system
- Brake system: front disc brake, rear differential, brake lever on the left and engine braking enhanced by the setting of the electronic control.
- Colours: white, red, green, yellow, blue, black, orange (other colors on request).

PRS-EU8050 " Electromechanical Universal Test Machine, 50 kN, 220-240V, 50-60Hz, 1 ph.

PRS-EU8300 " Electromechanical Universal Test Machine, 300 kN, 220-240V, 50-60Hz, 1 ph.

PRS-EU8050, 50 kN and PRS-EU8300, 300 kN capacity fully automatic Electromechanical ParsRos Universal Testing Machines are multi purpose versatile machines which satisfy the requirement of R&D laboratories, university laboratories, institute laboratories and quality control laboratories for tensile, compression flexural tests under load or displacement control for a wide range of materials. PRS-EU8050 and PRS-EU8300 model Electromechanical Universal Testing Machines can be used for tensile test on any material i.e (metal, plastic, textile, wood) by using suitable accessories.

Those machines can also be used for general compression, flexural, test on steel, soil, concrete, cement, asphalt and similar materials, by using suitable accessories.
These Testing Machines consist of base containing the transmission components and holds two robust columns connected by upper cross head and digital graphics data acquisition and control system.

The upper cross head can be adjusted to set the vertical test space for different tests. User can adjust the vertical test space by also lower crosshead moved by an electromechanical system with a single recirculating ball screw, powered by an servomotor.

Advanced closed loop control system assures accurate load or displacement pace rate on sample.

The load is measured by a load cell that located on upper crosshead and displacement is measured by an encoder fit to the servo motor on both models.

The operator will have large flexibility during the test with advanced microprocessor control and material testing software installed on PC.

The machine is supplied complete with high precision load cell. Gripping systems, extensometers and accessories are not included and have to be ordered separately.

Totally two identical 145 kW wind turbine units, made in 1988 by Danish A/S Nortank, total operating hours approx 75000. The equipment have been dismatled since 2008 and inspected and serviced for operation condition and they are ready for immediate delivery

We have totally 2 units of uninstalled complete wind turbines manufactured by Danish A/S Nordtank in year 1988, manufactures type NTK 130 with rated power of 2 x 145 kW. The mills are in good operational condition and ready for immediate shipment. The hubs are heat treated MEEHANITE hubs made by company SABROE and are equipped with cast iron construction which allows adjustment for blade pitch angle. The blades are made by Danish company LM- Glasfiber, material is glass fiber reinforced polyester and they have self-supporting structure with bushing roots. The blades have also hydraulically activated tip brakes which automatically rotate the tips to a 90 degree break angle when wind is lost or it can be used for maintenance stoppage. The gear box in made by German Lohman & Stolterfoht and it is two step planetary gear type with high AGMA rating of 302 kW. The break system is 100% fail safe Nortank’s own hydraulically / mechanically activated brakes. Both units have they own Motorola 6809 multi-microprocessor operated control units which are housed in dust proof steel cabinets.

More information on requests, for spam protection please introduce yourself properly.

Main data of one mill:
Manufacture’s type: NTK 130F/LM
Year of manufacture 1988
Total operating hours: approx. 75000
Rated capacity, max: 145 kW
Number of blades: 3 pcs
Rotor diameter: 22 m
Rotor speed: 44.5 rpm
Cut-in wind speed: 4.0 m/sec
Cut-out wind speed: 53 m/sec (120 mph)
Hub height: 26 m
Generator: ASEA 145 kW / 1500 rpm / 50 Hz
Blade type: LM 9.7 m H/H/T diam. 21 m
Gear box type: Lohman & Stolterfort GPC 145
Clutch type: Lohr & Brokamp Universal Joint No 105
Total weight: 15200 kg.

Electric small tower tractor.

SPECIFICATIONS:
Biga 'Pick-up versions and performance with the vehicle in perfect working on flat surface.

type 13 max 5 Km / h + / - 10% P / T 800 kg. on the P / T 100 Kg on slope 15%
Type 19 max 6,5 Km / h + / - 10% P / T 600 kg.
Type 28 up to 8 Km / h + / - 10% P / T 400 kg.
Type 34 up to 11 Km / h + / - 10% P / T 200 kg.
The maximum range is considered with the load evenly distributed on the plane and the center of gravity of the goods must not exceed the height of mm. 350.

Dimensions:
Total Length mm 1540 Width mm. 740 Height mm. 1130
Floor Length mm 940 Width mm. Ground Clearance 740 mm. 310
Weights:
Total including batteries and banks kg. 176th
September 3 banks kg. Batteries kg. 36 each. x 2
Motor:
permanent magnet motor RR 10/1 800 W - rpm from 330 to 24 V.
N. 2 batteries 12V 140 A sealed gel - connected in series, without maintenance.
External charger 24 v - 12 amp - electronic microprocessor - 220 v.
transmission:
Differential, max. 2 Kgm torque - 2 Shaft with graft rejection in 6 slot.
chain drive with front and rear sprocket.
Brakes:
Front drum, drive with your right hand.
Rear disk drive with his left hand.
brake, drive on left lever.
increased by releasing the brake (engine brake) enhanced in the calibration of the parameters of the controller.
Covers: 3.00-4 rubber tires
Frame:
Tubular steel and Fe 37 powder-coated polyester for outdoor Ral 9007.
lighting and signaling devices :
Headlight main and tail lights - reverse buzzer, horn.
phonometric values: values ??LpAm max = 77.6 - 85.6 LWA - Attendant Leq dB (A) 77.6
Vibration value: vmax (i) = 0.47 m / s2 (maximum value for operator sitting in the driver's seat).

Spare parts and tools for the maintenance and repair:
Original spare parts and tools for maintenance and repair are provided directly to order from Italy Bigà spa.

A series EAGLE is composed of two models for electrosurgery which can all be connected to an independent Argon gas module and max. powers of 400 W and 280 W; there is also one model for electrosurgery which built in Argon gas and max. power of 400 W. The units have got 17 currents: 10 for the monopolar usage and 7 for the bipolar usage. Three for the monopolar cut, Three for the monopolar cut, Four for the monopolar coagulation, Two for the bipolar cut, Two for the bipolar coagulation, Two for the bipolar coagulation, One for the coagulation / sealing of big vessels. All the output currents are completely self controlled through a micro-processor with three different systems: - ADC System - APC System - Starting impulse control, which electronically checks the starting pulse of the cut currents. The EAGLE models are equipped with a circuit that can verify the connection/contact of the neutral electrodes ônon Splitö type with a single section and ôSplitö type with a double section with interrupts delivery of the power and luminous acoustic alarm signal. The units can be used with one double pedal footswitch, which allows the activation of the monopolar or bipolar functions, and with a second double pedal foot-switch, which is indicated for the independent activation of the bipolar functions only. The all models allow memorizing and then selecting through a simple button 100 complete functioning programs and are equipped with: two monopolar outputs, which can be used at the same time by two different operators through the Twin activation device; two bipolar outputs. All models are equipped with an auto-check system at double microprocessor: - Main Auto-Check, main auto-diagnosis procedure at the switching-on. - Standard Auto-Check, continuous check of all the functioning parameters during the usage. - Immediate interruption of the functioning with contemporary alarm signal for the operators through specific Error Codes HF Leakage Control, check of the high frequency leakage currents to earth. Auto-Check Argon section. Automatic output of the right modulated and pulsed spray coagulation when the Argon gas coagulation is activated independently from the type of coagulation selected for the simple electro-surgery, and selfcompensation of the gas flow according to the diameter of the electrodes, with a perfect control of the penetration depth. The units can be equipped with automatic activation aspirators that guarantee the efficacious and silent elimination of smokes or electro-surgical aerosol.

700+ MHz
128 Ram
10GB Hard drive


17000 Pcs Available

Telescopic automatic door

Genius design
Ideal system for norrow gates
Suitable for most building types
Microprocessor controlled
Standard 2 year dss warranty
Safety
Energy saving.

TVModulator -SMATV headend
Features:
Compact 8&5 channel , agile modulator
for SMATV applications
Microprocessor controlled.
Universal, user-friendly programming
19 inch and wall mount versions available
SMPS(85-265VAC),

Metal detector(hand held)
Microprocessor controlled
Auto calibration
Advanced technology
High sensitivity
Membrane touch pad buttons
Long battery life
Push button ultra high recovery
Replaceable & rechargeable battery
Metal density vu-meter
Audible & visual alarm
Charger, belt holder, battery, wrist stripe included
Optionals:vibration, earphone

Reading can be viewed instantaneously on display.
Microprocessor controlled.
Measure the ethylene oxide concentration in air in the 0-99 ppm range.
Visual and Audible Alarm (> 85 dB(A))
External Alarm output
Adjustable alarm threshold.
Fixed system installation continuously monitoring a given area.
High reliability
Instrument checks sequence.
Two-year limited warranty includes a sensor
Up to five years of sensor life.
Economic.

Asuring via digital
Gearcase. Such microprocessor control is designed to optimize the
Charging cycles for any type of battery.
• 230v coil three-pole contactor.
• d.C. Fuse on rectifier output.
• delta-star stray flux three-phase power transformer class h;
Impregnated in autoclave with ecological epoxy resins, with
Thermocouples for disconnection due to maximum temperature.
• three-phase rectifier bridge with silicon diodes, natural cooling, with

A fully automatic, microprocessor-controlled dental furnace for all types of ceramic dental restorations,
Vacuum and atmospheric firing, furnace soldering of ceramic work.Equipped with the tested and tried quartz muffle for long life and ultimate performance.
* 100 freely definable firing programs
* user-friendly control of firing sequences
* freely changeable standby, pre-drying, end and cooling temperatures
* temperature rise time changeable in ¦c/min.
* each program with slow cooling option
* highest temperature accuracy.

1-15 kVA 1 Phase Input - Output Online UPS.
Atlas 100 Series Online UPSs protect monophase critical loads against utility failures and irregular voltage cases. They are producing pure sinewave output via microprocessor controlled, manufactured with the state of the art PWM and IGBT technology. Galvanic isolation transformer, parallel operability, communication port are available. IT applications, small offices, service providers, communication networks, control equipments, automation systems etc. are the main fields of use with a proved reliable high technology.

5 - Foot sheet chariot
5.1 Dimensions:
Total length 930 mm Width 650 mm Height 1070 mm
Plan Length Width mm 870 mm 620 mm Ground clearance 330

5.2 Weights:
Total 77.90 kg including batteries
Batteries 13 kg each. x 2

5.3 Motor:
Permanent magnet motor with electric 200 W - rpm from 120 to 24 V electro 2Nm 24VDC.

5.4Voltaggio and batteries:
N. 2 x 32 A 12 V sealed gel in C5 - series connection, maintenance-free.
External charger 24 V - 8 amp - Electronic microprocessor - Power supply 220 V

5.5 Brakes:
Electric brake to the engine block, insertion of a power failure.
Braking on deceleration (engine braking) enhanced in the setting of parameters
control unit.

5.6 Speed and Capacity (performance of the vehicle in perfect working flat route:
Maximum speed in 6 seconds of continuous accelerated 5 km / h + / - 10%
Max capacity 250 kg and 100kg in terms of gradient of 15%.
The maximum flow is considered with uniformly distributed load on the floor.

5.7 Tyres:
2 rubber wheels mounted on wheels with pneumatic 3.00-4 6-ply roofing.
2 wheels 200x50 core diameter polypropylene ring mounted on gray synthetic rubber supports
swivel.

5.8 Structure:
Tubular and sheet S 235 JR polyester powder coated RAL 6018 external

5.9 Spare parts and tools for maintenance and repair:
The original spare parts and tools for maintenance and repair are provided directly
Order by Biga spa Italy.

5.10 Values sound level: less than 70 dB (A)
5.11 Environmental conditions: temperature + 5 + 40 C Humidity 50%.

Technical parameters:

- Voltage ranges 0.2 do 1000 V,
- Current ranges od 20 mA do 20 A,
- Frequency ranges od 40 Hz do 5000 Hz,
- Voltage and current accuracy DC 0.02%,
- Voltage and current accuracy AC 0.05%,
- Load carrying capacity 40 VA,
- Serial interface RS232, USB, Ethernet.

The INMEL 1000 calibrator was made on base of modern componenets of microprocessor technologies. Applicated technologies are comparable with technologies used by leading global companies.The INMEL 1000 calibrator characterize oneself the innovative structure of operation in range of output signals and operation of measuring and regulatory loop.For AC course possible is the synchronous operation with the main. This possibility influence on output parameters, reliability, comfort of work, the communication way with user and external devices. The calibrator INMEL 1000 fulfils directives of the European Union within the range safeties and the electromagnetic compatibility:The production of the INMEL 1000 calibrator does not create threats for environment.

Application:
Checking ang calibration:
- AC and DC voltmeters,
- AC and DC ammeters,
- frequency meters,
- measuring transducers.

6-30 kVA 3 Phase Input - 1 Faz Output Online UPS.
Atlas 200 Series Online UPSs protect monophase critical loads against utility failures and irregular voltage cases where you have three phase electricity. They are producing pure sinewave output via microprocessor controlled, manufactured with the state of the art PWM and IGBT technology. Galvanic isolation transformer, parallel operability, communication ports are available in the standard models. Industrial automation, integrated facilities, building security automation, medical, communication and laboratory equipments, etc. are the main fields of use with a proved reliable high technology.

10-300 kVA 3 Phase Input - 3 Faz Output Online UPS.

Atlas 3000 Series Online UPSs protect thr critical loads against utility failures and irregular voltage cases where you use three phase electricity for the loads. They are producing pure sinewave output via microprocessor controller, manufactured with the state of the art PWM and IGBT technology. Galvanic isolation transformer, parallel operation, communication port are available in the standard models. Industrial manufacturing machines, hospital and monitoring equipments, heavy, medical, communication and laboratory equipments,etc. are the main fields of use with a proved reliable high technology.

ZIM 18 Concrete Block (Hollow Block) Machine: Is special design machine for block production that works fully automatic.The movement of the machine is programmed the PLC microprocessor computer.
By changing moulds all kinds of blocks, lentos and precast concrete elements can be produced in a serial way.
20cm block can be produced 18 units in one press. Machine is able to produce the insulated block upon demand.
We use pneumatic bellows in machine mould connections, due to this system vibration on mould is expanded regular and uniform.
Motrar part of the machine is moving on strong chromium columns. Height regulations also done automaticly but not with manpower.

PLUSTEAM Series Steam Sterilizers are available frmom 1 STU (96 L) capacity to 14 STU (945 L). Double or single door cofigurations are possible with hinged, automated sliding or manual sliding options.
* Chamber,jacket, steam generator & doors from AISI 316 L quality stainless steel
* Panels from AISI 304 quality stainless steel
* All piping, fittings, valves and corner sections are from AISI 304 or AISI 316 quality stainless steel
* 7" LCD Color TFT Touchscreen with microprocessor controlled PLC controller
* Thermal Printer
* Various optional features and accessories are available upon request



Packed in wooden crate. Covered with PE film & bubble nylon and supported with foams on panels.

This device operates with 1 or 2 measuring cells. After entry of test-specific sample data into the controller, the test is completely automatically carried out and evaluated. The device has an interface for a generally commercially available printer. Scope of equipment delivered: automatic air permeability tester, 1 bottle of fill oil,
500 ea. Round filters (diam. 41 mm),
100 ea. Dust filters (diam. 13 mm),
1 ea. Tamper
Dimensions: 200x160x400 mm
Weight: 12 kg

Dimensions

Lactomat Rapid BP is a compact ultrasonic milk analyzer equipped with double measuring cell, balloon pump and inbuilt ventilation system for prevention of overheating in hot environments. Fast and high technology testing in 18 sec. only. Microprocessor from new generation and improved software. SMPS based power supply, separated serial ports for printer and PC. Stainless steel and plastic housing.Three calibration channels are available. Standard calibrations for milk analyzer Lactomat Rapid DP are for Cow milk, Sheep milk, UHT. The analyzer can be calibrated also for: Buffalo milk, Pasteurized milk, Goat milk, Mixed milk, Skimmed milk, Whey and other types of milk and milk derivatives.

Over voltages, polarity reversal, anomalies.
Error code of any anomaly, inner self ventilation
Through forced air, efficiency > 85%, mass-produced
Mains leads, input cable, connection to the battery
Through anderson-rema power terminals.

Nfm
Switching battery charger, high frequency technology,
Fully controlled by microprocessor.
240v single-phase +- 10%, luminous display for a
Easy reading of the charging parameters.
Different charging curves in accordance with the kind
Of battery and choose among 16 standard curves,
Preprogrammed valid for pb-acid, gel.
Battery voltage and charge current can be changed
Through the button in the front panel.
“soft start” mode and display of the charging cycle
With led .
Electronic protection and/or fuse against short circuits
Over voltages, polarity reversal, anomalies.
Error code of any anomaly, inner self ventilation
Through forced air, efficiency > 85%, mass-produced
Mains leads, input cable, connection to the battery
Through anderson-rema power terminals.

Nfc
Switching battery charger, high frequency technology,
Fully controlled by microprocessor.
240v single-phase +- 10%, luminous display for a
Easy reading of the charging parameters.
Different charging curves in accordance with the kind
Of battery and choose among 16 standard curves,
Preprogrammed valid for pb-acid, gel.
Battery voltage and charge current can be changed
Through the button in the front panel.
“soft start” mode and display of the charging cycle
With led .
Electronic protection and/or fuse against short circuits
Over voltages, polarity reversal, anomalies.
Error code of any anomaly, inner self ventilation
Through forced air, efficiency > 85%, error code
Display missing, mass-produced input network cable,
Output cables polarized.

Vending machines

International norms, in conformity with ce norms and produced under iso 9001:2000 qms
Fully microprocessor controlled
Large illuminated advertisement/product display panel
Coin operated can be figured for 16 different coins
Compatible to all currencies
Continuous operation with ups
User friendly interface with ld screen display
Bite(built-in test equipment) automatically fixing problems and/or warning messages on lcd
Remote access to settings and recorded data from a distance pc via rs232 interface
Highly-corrosion-resistant automatic beverage/snack vendor
Memory incorporated with improved theft security
Adjustable price control unit for each selection
Easy-to-load beverage/snack vending machine
Customer's specifications accepted
Oem availability for quantity orders

Lactomat Rapid SBP is compact ultrasonic milk fat testing machine. Fast and high technology testing in 18 sec. only. Microprocessor from new generation and improved software. The milk analyzer is equipped with double measuring cell, balloon pump and inbuilt ventilation system for prevention of overheating in hot environments. SMPS based power supply, separated serial ports for printer and PC. Stainless steel housing.Three calibration channels are available. Standard calibrations for milk analyzer Lactomat Rapid SBP are for Cow milk, Sheep milk, UHT. The analyzer can be calibrated also for: Buffalo milk, Pasteurized milk, Goat milk, Mixed milk, Skimmed milk, Whey and other types of milk and milk derivatives.

We supply and export all kind of CPU computer scrap such as Intel Pro, Cumeric, Pentium Pro etc We sale at very cheap rate and delivery within 14 Days, please contact with email for more details and pricing.
Product details,
wholesale computer cpu / processor scrap
General information
Type CPU / Microprocessor
Market segment Server
Family Intel Xeon
Model number E5640
CPU part number AT80614005073AB (SLBVC)
Box part number BX80614E5620 (SLBVC)
Frequency (MHz) 2667
Bus speed (MHz) 2933 MHz QPI
Package 1366-land Flip-Chip Land Grid Array (FC-LGA10)
Socket Socket 1366 (LGA1366)
Size 1.77" x 1.67" / 4.5cm x 4.25cm

New ultrasonic milk analyzers, Rapid S from the Lactomat series are the fastest high-end instruments used for measuring the basic components of the milk. Powered be new generation microprocessor with 20 times more capacity for data processing. Accurate analysis of the components is carried for 18 seconds for sample temperature 28° C . Milk analyzers Lactomat Rapid are compact devices equipped with double measuring cell and inbuilt ventilation system for prevention of overheating in hot environments. Stainless steel housing. Three calibration channels are available. Standard calibrations for milk analyzer Lactomat Rapid S are for Cow milk, Sheep milk, UHT. The analyzer can be calibrated also for: Buffalo milk, Pasteurized milk, Goat milk, Mixed milk, Skimmed milk, Whey and other types of milk and milk derivatives.

Features:

- Microprocessor based with Printer Interface.
- PC Compatibility through RS 232 Interface (optional)
- Four-element measurement in single aspiration of the sample
- Calibration curve programmability using maximum of 20 standards in the range of interest of the user.
- Data processing through optional curve fitting techniques-lease square, quadratic.
- Multiple calibration curves saving facility.

Applications:
To determine Na, K, Ca & Li in Plant materials, food and beverages Electrolytes in serum Body fluids (blood, urine etc.) Alkali & alkaline earth metals Nutrient solutions for cultivation of antibiotics Water (natural, spring, waste, river etc) Soils, cement, rocks etc.. In the areas of Agriculture, Food, Mining, Metallurgy, Pharmaceuticals, Pathology, Pollution Monitoring, Geology, Research Laboratories, Industries and Others.

Dimensions: 430 x 230 x 235mm
Weight: Approx. 10Kg.

New ultrasonic milk testing machines, Rapid from the Lactomat series are the fastest high-end instruments used for measuring the basic components of the milk. Powered be new generation microprocessor with 20 times more capacity for data processing. Accurate analysis of the components is carried for 18 seconds for sample temperature 28° C and 15 seconds for 38° C . Milk analyzers Lactomat Rapid are compact devices equipped with double measuring cell and inbuilt ventilation system for prevention of overheating in hot environments. Stainless steel and plastic housing. Three calibration channels are available. Standard calibrations for milk analyzer Lactomat Rapid are for Cow milk, Sheep milk, UHT. The analyzer can be calibrated also for: Buffalo milk, Pasteurized milk, Goat milk, Mixed milk, Skimmed milk, Whey and other types of milk and milk derivatives.

-International Norms
-Fully Microprocessor Controlled MDB Interface Full View Multi-Selection with Large Double Glazed LOW E Glass Front
-Easy to load beverage
-Large advertisement panel and add space on both sides
-Compatible to all currencies
-User friendly interface with 2x16 LCD screen
-Easy different tray and/or selection pricin g feature
-Real Time Time/Date function enabling timeable pricing
-Preset timetable power saving mode with programmable low tempature level and time controlled illumination
MDB,EXECUTIVE,PARALEL,CCTALK Compatible system configuration
-Electronic thermostat controlled wide range cooling feature and hidh capacity cooler
-Vario temparature different temp. zone operation with optional cooling and temparature display on LCD
-Silent and Vibration free operation
-Swinging and counterbalanced product dispensing slot
-Ensures reliable operation with product
among features....

The top of the aerosol therapy equipment. Maximum portability with exceptional performance.
This electronic device for aerosol therapy can be used anywhere since it can work with unit electrical adapter or with rechargeable batteries (optional).
The nebulization is very fast and can be adjusted to three different levels.
The nebulized particles are extremely effective with a very low MMAD able to reach the deep airways.
The total lack of noise, the presence of a base that can be fixed with velcro to the child's bed, makes the product extremely comfortable and suitable for pediatric use.
As a matter of fact, a mother could also perform the therapy while holding the baby in the arms or while the baby is sleeping in bed.
The total absence of noise won't intimidate the children and will make the therapy easier.
The electronic functions are controlled by a microprocessor.
The LCD screen informs you of the working status, facilitating the use of the product.
The device has a nebulizing chamber that ensures the thermal stability of the atomized medicine preventing any alteration.
Also tested with beclomethasone and budesonide.

Maximum speed: 1cc minute - 1 ml minute
Particle dimension range: 90%

ZIM T1200 machine can produce pipes 300mm - 1200mm diameter and 500mm - 2500mm height by single, double and triple pressing. 150mm and 200mm pipes also can be produced for special demands.

Machines can be designed semi or full automatic according to requirements.
We use SIEMENS brand PLC microprocessors on automatic machines.

There exists motrar bunker and motrar filling systems on machines.

Produced materials can be carried to drying area with carriage carts or forklifts.
Production is done on production pallets,

Materials up to 800mm diameter are carried to drying area with carriage carts, pipes bigger than 800 mm diameter can be carried with forklift. For fast production, pipes bigger than 300mm diameter also can carried to drying area with forklift.

Machine makes production by hydraulic press and vibration.
Vibration system of the machine is special design of ZIM Engineers. Vibration system which have oil cooling system and special oil unit. This system can be controlled electronically.

Special designed strong chassi of the machine enables long live producing without errors.

ZIM 1536 PLUS Block and Paverstone Machine is special design machine for block and interlock production that works fully automatic.The movement of the machine is programmed the PLC microprocessor computer.

By changing moulds all kinds of blocks, paverstones, curbstones, grass stones, lentos and precast concrete elements can be produced in a serial way.

20cm block can be produced 15, interlock paverstones can be produced 36 units in one press. Machine is able to produce the insulated block upon demand.

Thanks to special features developed by our engineers machine have very short cycle time. For example mould changing is wery easy and take short tme in new system.

Automation system and operator panel which is developed and redesigned in long years become user friendly and useful.

With our special design vibration table you can produce high quality products with less energy.

We use pneumatic bellows in machine mould connections, due to this system vibration on mould is expanded regular and uniform.

Service and maintenance is easy thank to our strong machine chassis and ergonomic design

ZIM 1536 PLUS Block and Paverstone Machine is special design machine for block and interlock production that works fully automatic.The movement of the machine is programmed the PLC microprocessor computer.
By changing moulds all kinds of blocks, paverstones, curbstones, grass stones, lentos and precast concrete elements can be produced in a serial way.
20cm block can be produced 15, interlock paverstones can be produced 36 units in one press. Machine is able to produce the insulated block upon demand.
Thanks to special features developed by our engineers machine have very short cycle time. For example mould changing is wery easy and take short tme in new system.
Automation system and operator panel which is developed and redesigned in long years become user friendly and useful.
With our special design vibration table you can produce high quality products with less energy.
We use pneumatic bellows in machine mould connections, due to this system vibration on mould is expanded regular and uniform.
Service and maintenance is easy thank to our strong machine chassis and ergonomic design

Technical sheet Biga’ pick-up:
Dimensions:
Total Length mm 1541 Width mm. 740 Height mm. 1120
Worktop length mm 95 Width mm. 740 Height from the ground mm. 310

Weight:
Total including batteries and banks kg.156
Set 3 banks kg. 4
Batteries kg. 27,5 each x 2

Gear Motor:
Permanent magnet engine R.R. 10/1 800 W – rpm 330 – 24 V.

Voltage and battery:
N. 2 batteries capacity 12V 140 A C20 hermetic gel– connected in series, no maintenance.
External battery charger 24 v – 12 amp – electronic microprocessor control- Power 220 v.

Differential and transmission:
Differential, maximum torque of torsion 2 Kgm - 2 Semiaxis with graft at 6 caves
Type 13: transmission chain, Sprocket 13 teeth, Crown wheel 45 teeth, Ratio 1/3,47
Type 19. transmission chain, Sprocket 19 teeth, Crown wheel a 45 teeth, Ratio 1/2,37
Type 23: transmission chain, Sprocket 23 teeth, Crown wheel 45 teeth, Ratio 1/2,00
Type 28: transmission chain, Sprocket 28 teeth, Crown wheel 45 teeth, Ratio 1/1,61
Type 34: transmission chain, Sprocket 34 teeth, Crown wheel 45 teeth, Ratio 1/1,33

Brakes:
Front drum brake, activation with right hand
Back drum brake, activation with left hand
Service brake, activation on left lever.
Braking increase by the release of the accelerator (engine brake) enhanced in the setting of the parameters of the junction box.

Speed and capacity:
Towing besides the driver (performance with the vehicle in perfect efficiency) on flat road. The maximum capacity is considered with uniformly distributed load on the worktop and the center of gravity of the goods must not exceed the height of mm. 350
Type 13 max 5 Km/h +/- 10% P/T 800 kg. on the plane P/T 100 Kg. on slopes 15%
Type 19 max 6,5 Km/h +/- 10% P/T 600 kg. on the plane
Type 23 max 8,5 Km/h +/- 10% P/T 450 kg. on the plane
Type 28 max 10,5 Km/h +/- 10% P/T 300 kg. on the plane
Type 34 max 12 Km/h +/- 10% P/T 200 kg. on the plane

Tires:
Covering: 3.00-4 superelastic rubber

Structure:
Tubular and sheet Fe 37 polyester powder painted for outdoor use Ral 9007

Lights and Devices:
signaling and illumination main headlight and tail lights reverse buzzer, horn.

Product Code

PRS-EU8050 : Electromechanical Universal Test Machine, 50 kN, 220-240V, 50-60Hz, 1 ph.

PRS-EU8300 : Electromechanical Universal Test Machine, 300 kN, 220-240V, 50-60Hz, 1 ph.

STANDARDS : EN ISO 6892-1, EN ISO 15630-1 and 2, EN ISO 7500-1

PRS-EU8050, 50 kN and PRS-EU8300, 300 kN capacity fully automatic Electromechanical ParsRos Universal Testing Machines are multi purpose versatile machines which satisfy the requirement of R&D laboratories, university laboratories, institute laboratories and quality control laboratories for tensile, compression flexural tests under load or displacement control for a wide range of materials. PRS-EU8050 and PRS-EU8300 model Electromechanical Universal Testing Machines can be used for tensile test on any material i.e (metal, plastic, textile, wood) by using suitable accessories. Those machines can also be used for general compression, flexural, test on steel, soil, concrete, cement, asphalt and similar materials, by using suitable accessories.
These Testing Machines consist of base containing the transmission components and holds two robust columns connected by upper cross head and digital graphics data acquisition and control system. The upper cross head can be adjusted to set the vertical test space for different tests. User can adjust the vertical test space by also lower crosshead moved by an electromechanical system with a single recirculating ball screw, powered by an servomotor.
Advanced closed loop control system assures accurate load or displacement pace rate on sample.
The load is measured by a load cell that located on upper crosshead and displacement is measured by an encoder fit to the servo motor on both models.
The operator will have large flexibility during the test with advanced microprocessor control and material testing software installed on PC.
The machine is supplied complete with high precision load cell. Gripping systems, extensometers and accessories are not included and have to be ordered separately.

PRS-EU8050 supplied with;

â?¢ Compression Platens
â?¢ Load Cells 50 kN Capacity

PRS-EU8300 supplied with;

Compression Platens
Load Cells 300 kN Capacity

ACCESSORIES
Electromechanical Universal Testing Machines are suitable for difference tests on various materials as Uniaxial Tests, Triaxial Tests, Steel Re-bars, Cement and Concrete, Soil (CBR), Asphalt (Marshall, Indirect Tensile, Duriez), Tiles, Flat Blocks etc. General Accessories;
1.PRSGM-0040 Load Cell, 5 kN Capacity
2.PRSGM-0042 Load Cell, 50 kN Capacity
3.PRSGM-0043 Load Cell, 300 kN Capacity
4.PRSGM-0115 Compression Platens, used to perform uniaxial and unconfined compression tests.
5.PRSM-0500 Extensometer for universal testing machine, 50 mm gauge length, 10 mm travel (to use with max Ã?:22 mm specimens)
6.PRSM-0520 Extensometer for universal testing machine, 50 mm gauge length, 100% strain feature, standard temperature range: -40°C to +100°C (-40°F to 212°F).

Assembly and disassembly of wide range of smd components from small chips to bgas
Microprocessor controlled 3 working modes:
Manual
Time (according to profile settings)
Profile
Using outer software it is possible to:
Control and edit the soldering/desoldering process save unlimited number of profiles
Optimized heating element power and intelligent hot air temperature control almost all smd components can be reworked
Wide scale of air flow regulation, starting from soldering with no risk of blowing off the components and soldering paste to large components (also on multilayer pcbs)
Built-in vacuum tweezer that can be started manually or automatically safe handling of sensitive components
Programming or manual outer system controlling (pcbs pre heater) enables to build a professional smd rework system based on ra-250e
Large, contrast display increases comfort of work and keeps the operator updated about current state of all important parameters
Adding assembly/disassembly hot air station with pre heater and stand we get advanced work station and possibility to perform works impossible so far to do.

Input power: 230 vac
Power consumption: 530 w max.
Air flow control range: 2-20 l/min, +/10%
Temperature control range: 100°c 450°c
Vacuum tweezer: 0.2 bar
Temperature stability: +/2°c

Ext. Dimensions: 200 x 230 x 150 mm
Weight: 4.4 kg

Ptek nre3 three phase is designed to recharge medium - large capacity traction
And start lead-acid batteries, developed using our forty-year experience in the field
Of battery chargers and multi-years application of microprocessor control systems
D electronic circuit conforming to the
Directive on electromagnetic compatibility and ce marking, automatic disconnection
Of battery charger due to battery disconnection, equalization charge based on
Time, charging with decreasing current (wa characteristic):9÷11 h charging time,
Transformer thermal protection, modular installation on galvanized steel base, sheet
Steel case with modular panels, epoxy powder coating, oven-baked, standard color:
Ral 5003 blue, option: custom-made color, logo and silk-screen printing, mains
Input and d.C. Output polarized cables, complete with mains and battery cables;
Assembly of plugs and battery connectors on request.
“wa” characteristic (din 41774):
Charge at decreasing current with intervention of adjustable final
Charge from 2.35 to 2.40 v/cell., final charge with timed control 9h /
11h, fixed charging time (equalization charge excluded), equalization
Charge (week-end charge). It will start after 55’ from charge end,
Duration of equalized charging phase: each hour 5’ (repeated for 48
Hours), calculation to determine the size of suitable battery charge:
16a for every 100 ah of the battery (e.G. 500 ah battery: 16ax5 =
80a).

Ptek nr3 three phase is designed to recharge medium - large capacity traction and
Start lead-acid batteries, developed using our forty-year experience in the field of
Battery chargers and multi-years application of microprocessor control systems which
On, short check of functions and
Times, option to program the equalized charge automatically, lab tested electronic
Circuit conforming to the directive on electromagnetic compatibility and ce marking,
Automatic disconnection of battery charger due to battery disconnection, equalization
Charge based on time, charging with decreasing current (wa characteristic): 9÷11
H charging time, transformer thermal protection, modular installation on galvanized
Steel base, sheet steel case with modular panels, epoxy powder coating, oven-baked,
Standard colour: ral 2004 orange, option: custom-made color, logo and silk-screen
Printing, mains input and d.C. Output polarized cables, complete with mains and
Battery cables; assembly of plugs and battery connectors on request.
“wa” characteristic (din 41774):
Charge at decreasing current with intervention of adjustable final
Charge from 2.35 to 2.40 v/cell., final charge with timed control 9h /
11h, fixed charging time (equalization charge excluded), equalization
Charge (week-end charge) to be recalled. It will start after 55’ from
Charge end, duration of equalized charging phase: each hour 5’
(repeated for 48 hours), calculation to determine the size of suitable
Battery charge: 16a for every 100 ah of the battery (e.G. 500 ah
Battery: 16ax5 = 80a).

ZIM 1230 Concrete Pavers and Block Making Machine; It is a machine that works fully automatic. The movement of the machine is programmed the PLC microprocessor computer.

By changing moulds all kinds of pavers stone , curbs, block and precast concrete elements such as grass pavers series can be produced in a serial way.

20cm block can be produced 12 units in one press with the machine,or 30 interlock stones can be produced in a press. Machine is able to produce the insulated block upon demand.

Our companyâ??s special production vibrator is used. Thus, it can produce smoothly and quickly.

Pneumatic bellows cylinders are used in connection of the mold of the machine. In this way a more uniform vibration propagation in the mold is obtained.

Other than the mold and the press, thin and the bold mortar sections are moved over the hard chromium-plated column mills as well.

A model with a single hopper, ZIM 12, is also available for manufacturing single layer bricks/pavers, hollow block, and for special blocks/pavers.

Machine Dimensions: Width / 9600 mm - Height / 6000 mm - Length / 16500 mm
Control System: Full Automatic (PLC)
Pallet Dimensions: Pallet with leg:1400mmx1450mmx50mm
Rack System:1400mmx1450mmx50mm
Mould Usage Area: 1300mm x 1350mm
Minimum Product Height: 50 mm
Maximum Product Height: 300 mm
Pressing Time: 17 â?? 25 seconds
Capacity of Motrar Bunker: 2 x 2500 dm³
Working Pressure: 80 â?? 150 bar
Electric System: Schneider - Siemens
Total Weight: 36.500kg

*Maxi Double Premium Model is taken as base.

Air handling unit (ahu)

8 different models which provide required humidity and temperature by conditioning air volume in wide ranges.

Standard series
Application area: business centers, schools, hospitals, factories, hotels and restaurants.
8 different models which provide required humidity and temperature by conditioning air volume in the range of 3000m¦/h and 100.000 m¦/h.
The framework which is formed by combination of aluminum frames, which are connected specially, with plastic and aluminum comers.
Boards which are made up of double skilled galvanized iron in a standard way.
Polyurethane insulated panels, which are 30 mm in thickness, for thermal and acoustic insulation in a standard way.

Standard accessories;
Filter chambers; chamber design which provides easy mounting and de-mounting in filters and filters with different productivity levels on demand.
Heating and cooling coils; seamless cooper tubes. In heating coils, 4 options: warm water, vapor, hot water, electrically heated; in cooling coils, 2 options: chilled water and dx (direct expansion).
Dampers; rigid aluminum frame in multi airfoil structure which is the least resistant against airflow. Rubber gaskets which reduce air leakage through blades to the minimum level.
Fans; statically and dynamically balanced aspirators and ventilators in double inlet belt driven centrifugal type. Forward curved fans in systems with low, medium and high duct pressures, .
Optional accessories;
Gonka vapor humidifier, standard vapor cylinder, immersion electrodes, stainless vapor distributor and microprocessor control unit.
Mufflers which are made up of coulisses to provide required sound holding capacity.
Plate heat exchanger or heat recovery wheel for recovery of the heat emitted with exhaust air.
Electrical board.
Frequency converter


Depends on the size, model and chambers

Powerful and safe - manufactured in Germany.
Optionally with following light sources:
1) fluorescent lamp 15W - 900 lumen.
Lifetime 8000 h, white light.
The brightness is similar to 75w halogen light.
2) or fluorescent lamp 18W - 1200 lumen,
Lifetime 12000 h, white light.
The brightness is similar to 90w halogen light.
3) or with power LED lamp 15W - 1200 Lumen,
Lifetime 40000 h, white light.
The brightness is similar to 90w halogen light.
4) or sodium low pressure lamp LPS 18W - 1770 lumen.
Lifetime 18000 h, yellow light.
The brightness is similar to 120w halogen light.
Solar Panel: 75W / 100W / 120W mono crystalline silicon (protecting glass, hail-proof) aprx. 25 years life duration.
This modern module technology has a high degree of efficieny and allows charging also at cloudy weather.
Solar battery: 12V maintenance-free power gel accumulator 12 volt. Life time: 5-8 years.
Functions well under low temperature.
Control: Microprocessor for automatic lamp start by light sensor,
turn-off by dawn or by the adjustable timer, e.g. after. 8 hours.
Over-charge and low-discharge protection for the battery.
Pole: Steel hot-dip galvanized, height 500cm + 80cm for concreting.
Rigid plastic case for inground-mount for the batteries, (walk-over). Size 360 x 260 x 320mm.
Daily operation at dark-cloudy weather:
a) Standard version: 1 day (16 hours)
b) with extension kit autumn: 2 days (24 h)
c) with extension kit winter: 4 days (40 h)
Distance from pole to pole = Lighted area Ø aprx. 25 meter
Ambient temperature: -35°C ~ +60°C
Maintenance-free (only sometimes is the cleaning of the solar panel required).
Included in the shipment: High-power battery, pole and lamp.

Passenger Lifts

The lift is ideal for retrofit within existing buildings with min. adjustment on site
self-supporting steel structure minimum headroom
pit 350 mm instead of 1300 mm
pre-installed cabin and drive unit
easy installation
controller with micro-processor plug-in system
complete drive unit in headroom (no separate machine room necessary)
Technical information
The information given below lists main features of our passenger lifts. Please do not hesitate to contact us for further details.
Structure
Steel structure, made of cold rolled galvanized special profiles with guides T 70 x 65 x 9
Buffer 80/80
Cabin
Cant-off system made of galvanized steel, adjustable guides shoes on two sides + emergency guiding
Compensation device on suspension chain
floor PVC covered
Cabin light (flush installation) - Cabin ventilation
Cabin push button station - emergency call - emergency light - emergency telephone call pre-installed
Governor operated safety, type tested
Special cabin apron (registered design application)
Hinged doors ISO-PM 225
manual operated hinged doors, made of primed painted steel, window in Aluminium frame
incl. door frame, Call button with stainless steel cover
type tested door lock with fail safety lock
Door closer - installed covered
Horizontal sliding doors ISO-PA 300
powered horizontal sliding doors made of primed painted steel
incl. door frame, cover panel, Call button with stainless steel cover
type tested door lock with fail safety lock
Machine room door
double hinged door galvanized with sash lock
with side frames made of galvanized steel
Drive unit
Drive unit with standard motor IP 54 and factory-made oil-filling, double disc brake and hand wheel, 3 x 400 V 50 Hz.
chain wheels for chains 5/8 x 3/8"
Controller
Microprocessor in controller cabinet
Installation pre-installed and plug-in system
Floor selector (impulse driven)