Temp Humidity And Vibration Test Chamber

Programmable Temperature and Humidity Test Chambers
3-Layers Temp Humi Test Chamber
Temperature Humidity Test Chamber
Temperature and Humidity Test Chambers provides an economical and space-saving solution for a variety of testing requirements. It can simulate different climatic conditions, such as heat-endurance, cold-endurance, dryness-endurance, and humidity-endurance, which defines the performance of material. By testing the product under different climatic conditions to see whether its performance can meet the intended requirements. It is widely applied in the industries of electron, electrical equipment, vehicle, metal, food, chemistry, building materials, luggage, adhesion tape, printing, packaging, and other product components and materials.
The programmer includes a temperature alarm as just one part of Grande's Three-tiered over-temperature protection system. A thermal fuse and a user-set independent limit are also included. In addition, a specimen power terminal allows the user to safely operate powered equipment inside or with the chamber.
Corresponding Standard of the Temperature and Humidity Test Chamber:
1.GB11158 high-temperature testing condition
2.GB10589-89 low-temperature testing condition
3.GB10592-89 high-low-temperature testing condition
4.GB/T10586-89 hu midity testing condition
5.GB/T2423.1-2001 low-temperature testing condition
6.GB/T2423.2-2001 high-temperature testing condition
7.GB/T2423.3-93 humidity testing condition
8.GB/T2423.4-93 alternating temperature testing machine
9.GB/T2423.22-2001 temperature testing method
10.IEC60068-2-1.1990 low-temperature testing method
11.IEC60068-2-2.1974 high-temperature testing method
12.GJB150.3 high-temperature test
13.GJB150.4 low-temperture test
14.GJB150.9 humidity test
Grande Expertise in Humidity Control
Controlling humidity in a small environmental chamber can be especially challenging. Grande expertise in humidity control brings intelligent design that is carefully integrated into the Criterion chambers. The humidity subsystems are designed for reliability, convenience, and performance:
An external steam generator allows expanded range and is easy to maintain.
A separate de-humidification coil improves low humidity control and range.
Wet-bulb humidity sensor is a �??primary measurement method�?? for accuracy. It is also economical, easy to maintain, and reliable because it has no risk of failure due to over-saturation. (Read why analog is preferred over digital.)
Direct water supply connection is standard, with options for water filtering and recirculating water tank.
Features
High performance and quiet operation (65 dBa)
Space-saving footprint, designed for flush installation to wall
Stainless steel exterior

3-layers temp humi test chamber
Programmable Temperature And Humidity Test Chamber
Temperature Humidity Test Chamber
It is applied to test the materials in heat-resistance, cold-resistance, dry-resistance, moisture-resistance. It is simple to operate and program easy to edit. It can show the set values and operative time.
Applied to test the prodcuts quality, such as electronic, plastic products, electrical appliances, instruments, food, vehicles, metals, chemicals, building materials, aerospace, medical care and so on.
The three-in-one design makes the equipment easy to operate and space-saving.Users can do different testings of high temperature,low temperature and costant temperature humidity condition in every single testing area.
Every system is entirely independant of each other,adopts 3 sets of refrigeration systems,3 sets of humidifying systems and 3 sets of controlling systems,so as to ensure stable and accurate controlling,and povide a longer service life.
Touch control & setting mode is totally controlled and locked up by automatic micro computer system with PID value automatic calculating ability.
Corresponding Standard of the Temperature and Humidity Test Chamber:
1.GB11158 high-temperature testing condition
2.GB10589-89 low-temperature testing condition
3.GB10592-89 high -low-temperature testing condition
4.GB/T10586-89 humidity testing condition
5.GB/T2423.1-2001 low-temperature testing condition
6.GB/T2423.2-2001 high-temperature testing condition

Temperature only test chamber/High and low temperature test chamber
Temperature Only Test Chambers
High And Low Temperature Test Chamber
Temperature chamber models designed to save lab space
The Temperature chamber series provides an economical and space-saving solution for a variety of temperature testing requirements.
Lowest temperature: -20 or -70�C (-4 or -100�F)
Highest temperature: 180�C (354�F)
The extended temperature ranges of the Standard series make testing at extreme conditions possible without buying a larger, stand-alone chamber. Two chamber sizes are available, as well.
The programmer includes a temperature alarm as just one part of Grande's three-tiered over-temperature protection system. A thermal fuse and a user-set independent limit are also included. In addition, a specimen power terminal allows the user to safely operate powered equipment inside or with the chamber.
Features
High performance and quiet operation (65 dBa)
Space-saving footprint, designed for flush installation to wall
Stainless steel e xterior
Full thermal break around doorframe
One 50mm (2") or 100mm (4") diameter cable port on left, with flexible silicone plug
Three levels of overheat protection, plus overcool protection
Easy lift-off service panels, electrical access on left
Detachable eight-foot power cord with plug
ETL listed electrical panel conforming to UL 508A
Touch-screen programmer/controller with Ethernet
Save 120 profiles with up to 1200 steps each (ramp, soak, jump, auto-start, end)
One event relay for external device control, plus specimen power interlock relay for safety
Grande exclusive options include: Web Controller for full remote access; Chamber Connect software for basic data logging and monitoring. USB and RS-232 ports available, as well.

Dust resistance test chamber
IP Dust Test Chamber
Dust Resistance Test Chamber Wholesaler
Applications
Dust resistance test chamber is designed for sealing performance test and reliability test, widely used in electrical, electronics, automobile, motorcycle, LED and other products. It is suitable for the work ability test on the shell sealing performance, product in dust free settlement, in the environment without apparent air flow or with a strong blast air and a large amount of sand dust, and similar conditions.
Specifications:
Dust proof test machine
1. We are manufacturer, offer reasonable price for you.
2. Customization of non-standard models are available.
3. Major parts adopt imported brands.
�Features:
Temperature Range: environmental temperature + 5~50?? (Adjustable)
Humidity Range: 45%~75% (Adjustable)
Metal net sta ndard nominal line diameter: 50mAirflow velocity in the chamber: 1.5m/s (adjustable range 0~4.99m/s)
Environmental air pressure: 85Kpa~106Kpa
Test dust: dry talcum powder, portland cement, smoke ash and etc.
Line spacing between the standard: 32m, 75m and 250m (There are three Metal nets)
Selecting dust concentration control instrument: get sample through the optical principle, show the dust concentration and automatic control powder quantity that entering into the Cabinet according to the concentration of the set: (needed cleaning compressed air source configuration, require the pressure: 1~3 kg/cm3)
Power supply: 380V 3phases 50 Hz/60Hz
Besides dust proof test machine, our business range also covers: �
Thermal shock chamber, Temperature humidity chamber, Ramp rate temperature chamber, Walk-in climatic chamber, Solar radiation test chamber, Ozone test chamber, Salt spray chamber, Industrial hot air oven, Dustfree hot oven, Temperature humidity control cabinet, Rain spray test chamber, Automatic glue dispensing machine, Climate and vibration combined chamber, Burn-in aging test room, Steam aging test chamber, Ventilation aging chamber, Vibration tester, Drop tester, Tensile tester, etc.
Grande Electronics is one of the largest ce certified dust test chamber manufacturers and suppliers in China and also known as one of the famous chamber brands. Our discount product is mainly featured by good performance and flexibility and low price. Welcome to order the customized and cheap chamber made in China with our factory.

Temperature Cycling Test Chambers
Fast change rates test chamber
Temperature Cycle Test Chamber
Fast change rates testing chamber is suitable for testing the changes of instruments,electrical,electronic products,machine�and�parts�under�the�rapid�temperature change�or�the�the�gradient�conditions, takes advantage of compact, modern scroll compressors to bring fast temperature cycling to small form factor. Temperature cycling rates from 5 to 20�C/min. are possible. Two different ultimate low temperatures are available: -40�C or -70�C.
The faster cycle times can be used to meet more aggressive test methods that require thermal stress during transitions. Significant test time can be saved in completing tests, as well.
To demonstrate performance, Grande uses the international standard IEC 60068 3-5 measured at the supply air. Temperature cycles are run from hot to cold extremes, and the middle 80% of the transition is timed to determine performance. Your actual cycling results will vary depending on methodology, including the start and end temperatures, and the amount of samples loaded.
Features
QUALITY CONSTRUCTION
Stainless stee l exterior and interior
Rounded interior corners for easy cleaning
Full thermal break around doorframe and door
Rotating door latch is easy and secure
Dual-layer insulation of fiberglass and expanded foam for thermal integrity
One 2" (50mm) to One 4" (100mm) diameter cable port on the left, with an impervious, flexible silicone plug
Easy lift-off service panels
Pressure relief port to allow air volume changes due to rapid temperature changes
Three levels of overheat protection
FTF PROGRAMMER/CONTROLLER
Popular PID controller with touch-screen operation
Stores 120 different profiles�with up to 1200 steps each (ramp, soak, jump, auto-start, end)
Step types include: ramp, soak, jump, auto-start, and end
Ethernet interface for remote monitoring and operation
RECOMMENDED OPTIONS
Dry air purge, to compensate for quickly shrinking air during cooling, as well as to reduce risk of condensation.
Product temperature control, allows feedback from a second sensor on the product. Ensures faster completion of transition steps.

High altitude low pressure simulation test chamber
Altitude Chamber For Sale
Altitude Test Chambers
Temperature testing at altitudes up to 100,000 feet.
Grande can provide custom-built chambers for simultaneous testing of temperature and low-pressure altitude conditions. Two common applications are:
Testing of avionics or other aerospace equipment to simulate actual conditions it might experience.
Simulation of high-altitude conditions like might be found in mountainous regions.
NOTE: Altitude test chambers are custom systems, and differing requirements may significantly change the cost and utility requirements. Please let Grande know as much detail as possible about your anticipated testing specification/method, and we can provide you with a tailored system for your requirements.
Features
Temperature range from -70 to 200C
Altitude range from ground to 100,000 feet
Optional humidity control when altitude system is off
Chamber interior size specified by customer
Automatic altitude control, integrated with temperature controller No manual setting of altitude level!
Vacuum pum p sized for climb/dive rate required by application
Viewing window and cable ports available

Liquid Thermal shock test chamber
Three Zone Thermal Shock Test Chamber
Thermal Shock Test Chamber
Liquid Thermal Shock Test Chamber,Cold and hot impact machine can be used to test material structure or composite material, in an instant by extremely high temperature and extremely low temperature continuous environment can endure degree, in order to in the shortest time test commits any heat bilges cold shrink caused by the chemical changes or physical damage. Applicable objects including metal, plastic, rubber, electronics, pv, solar... And other materials, the products can be used as a basis of improving or reference.
Significant reductions in fluid usage make liquid thermal shock affordable
Purchasing a liquid thermal shock chamber needs close consideration of the long term operating costs. The specialized liquids used can easily evaporate, causing the loss of thousands of dollars of fluid per year, if not properly contained. Liquid-to-liquid thermal shock testing is typically conducted to apply very strong, repetitive thermal stress to test pieces. It can model a product's ability to withstand thermally-induced size changes, crack resistance, hermetic integrity, and changes in electrical properties. This form of testing provides a very rapid temperature shock recovery of conditions, and it can significantly reduce testing time by requiring shorter soaks and less cycles. The liquid thermal shock chambers have been built to meet the demanding test req uirements, which has become a defacto industrial standard for semiconductor devices.

Salt corrosion spray test chamber
Configured for your specific tests
Alternate Salt Corrosion Spray Test Chamber
Grande makes rain and spray testing easier by offering a standard chamber capable of published and OEM proprietary test methods.
The standardized design can be configured for the rain/spray tests you need, eliminating the guesswork in buying a chamber. The system is based on the specification requirements, and can also accomplish individual automakers tests, as well as electrical-enclosure tests.
Our Design
Grande's modular design allows you to add on additional features, depending on the number and type of tests required. One possible choice is to integrate the spray system with a regular temperature and humidity chamber to save money and floor space, while also creating an opportunity to simulate actual operating conditions your product may experience.
Our system uses multiple control solenoids to vary the water's spray volume/pressure. A holding tank prepares the water to the desired temperature, if required. A pump ensures the water is delivered in the proper pressure range. The water is fed to a motorized manifold that rotates the spray arms. Each spray arm has an adjustable valve to allow finer control of the spray.
Testing capabilities
The specification is modeled after and doesnt differ greatly. Details about the nozzle types and the rotating nature of the spray arms and pro duct table are also included in the requirements. Additionally, drip and car wash tests are also specified.
Heavy splash/shower
S1 Spray room temperature water with 40 nozzles at 14.2 psi (1 kgf/cm2) for 30 minutes. The flow rate of the water shall be 6.5 gallons/min. (24.5 L/m).
S2 Spray room temperature water with 40 nozzles at 42.7 psi (3 kgf/cm2) for 60 minutes. The flow rate of the water shall be 10.3 gallons/min. (39.2 L/m).
Light spray/rain
R1 Spray room temperature water with two nozzles at 4.3 psi (0.3 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.8 gallons/min. (3.2 L/m).
R2 Spray room temperature water with two nozzles at 1.4 psi (0.1 kgf/cm2) for 10 minutes. The flow rate of the water shall be 0.5 gallons/min. (1.9 L/m).
Examples of OEM automotive manufacturers' requirements
Heat the sample to a temperature above boiling, then spray with cold water for about two minutes. Repeat cycle.
Heat the sample to boiling temperature, then spray with room temperature water for about fifteen minutes. Repeat cycle.
Simulate a car wash by using high pressure spray.
Features
Rotating rain and spray nozzles designed to JIS specifications
Speed control for the rotating spray nozzles
Stationary product shelf - A rotating shelf is optional: see options
Water pressure regulators, gauges and flow meters
Special high-volume floor drain system to rapidly drain water out of the chamber
Interior chamber size is the smallest possible area using the JIS specified nozzles
Applicable Test Methods

HAST PCT high-low temperature test chamber with pressure high pressure accelerated aging testing chamber factory�High Accelerated Stress Test
Steam Aging Test Chamber
Ozone Aging Chamber
Chamber/HAST Chamber
It test the resistance to pressure and air tightness for circuit board, multi-layer circuit board, IC, LCD and magnet iron. This machine is one of the common machine in aging equipment, used to test various types of materials for their performance under the condition of high temperature and high pressure. Application: Quality inspection for all types of electronic products, electric appliance, and products from communication, instrument, metal, plastic, automobile, food, chemical, building materials, medical and aerospace industries.
Pressure Accelerated Aging Test Chamber (HAST)
Safety�Device high pressure accelerated aging testing chamber factory:��
�1.�Safety�device�for�the�pot:�If�the�inner�box�is�not�closed�,�the�machine�can�not�start
�2.�Safety�Valve:�When�the�inner�box's�pressure�higher�than�the�machine's�undertake�value,�it�will�self-relieve.
�3.�Double�overheat�protection�device:�When�inner�box's�temperature�is�too�high,�it�will�alar m,�and�Automatic�cut�off�
the�heating�power.
4.�Cover�protection:�The�inner�box's�cover�is�made�of�aluminum�alloy,�can�protect�the�worker�from�scald.