Find Verified Industrial Heaters Burners Furnaces Ovens Suppliers, Manufacturers and Wholesalers

D6 Virgin Fuel Oil (often called D6 Virgin Oil, D6 Fuel Oil, or Residual Fuel Oil D6) is a heavy residual fuel obtained directly from the refining process and has not been previously used or reprocessed.

D6 virgin fuel = Bunker C, or Navy Special Fuel Oil.

It's the heavy, bottom-of-the-barrel fuel left after gasoline, diesel, jet fuel, etc. are distilled out of crude oil. Virgin just means it's straight from the refinery, not recycled/blended waste oil.

KEY SPECS:

Type: Heavy, high-viscosity residual fuel oil
Grade: Category 6 fuel oil - thickest grade
Viscosity: 650-900 cst @ 50C - like tar at room temp
Color: Black, dense
Energy: ~150,000 BTU/gallon - very high energy density
Sulfur: High, typically <3.5%. Low-sulfur versions exist but cost more
Flash point: Min 60C

Key Characteristics.
Fuel Type: Residual Fuel Oil
Appearance: Dark brown to black
Viscosity: Very high
Density: Higher than diesel
Heating Requirement: Usually required
Main Use: Industrial and marine fuel

D6 is a heavy fuel oil (HFO) primarily used for:
Power plants
Marine vessels (where regulations permit)
Large industrial boilers
Heavy industrial furnaces

1. Power plants - Boilers & turbines for electricity, often backup fuel
2. Large ships - Ocean tankers, bulk carriers, container ships as bunker fuel
3. Industrial - Cement plants, steel mills, big boilers/furnaces for process heat
4. Large generators - Backup power for factories/grid.

*Important: Special handling needed*
D6 is so thick/viscous it must be *pre-heated to 104-127C* before it can be pumped or burned. You need special storage tanks, heaters, and burners.

*Not for cars, small boats, or normal diesel engines*. It will destroy them. D2 diesel is much lighter and for trucks/cars - D6 is only for massive engines designed for it.

Cost vs Environment:
- Pros: Cheap per energy unit, high BTU, cost-effective for bulk use
- Cons: One of the most polluting fuels due to high sulfur + impurities SO2, acid rain. Regulations now require desulfurization.

D6 vs D2 diesel: D2 = light distillate for cars/trucks. D6 = heavy residual for ships/power plants. D6 has way more energy but also way more pollution and handling complexity.

It is much thicker and heavier than diesel or Jet A-1 and usually requires heating before it can be pumped or burned.

First Quality Oven Dried Lemon Rings 100% natural Cleaned Dried Private Label Bulk Packaging Oven Dried Fruit Slices Coctail
The lemons are harvested in the peak of the season from Southern parts of Turkey. They are washed and sliced into wheels, dried in the ovens without any preservatives. With its unique structure, delicate inside, rough skin make strong lemon flavor. Just add to your glass of water (cold or hot) see how it changes. It is a snack as well and good for baking. You can dip lemon into sweet or salty sauce, add to your yogurt or ice-cream. Dried lemon wheels are perfect ingredients for cocktails. Available both in retail and industry packaging options.

Bluestone Oil And Gas Ltd supplies industrial-grade black oil suitable for furnaces, boilers, power generation plants, manufacturing facilities, and marine operations. Our fuel oil provides dependable heat generation, stable combustion, and efficient industrial energy performance.

Iron Ore is a naturally occurring mineral material widely used in steel production, metal processing, construction, and industrial manufacturing applications. This raw material is valued for its high iron content, durability, and suitability for smelting and refining processes. It is carefully processed to maintain consistent quality, making it suitable for blast furnaces, foundries, and heavy industrial operations. Iron Ore is available in different grades and particle sizes to meet various industrial requirements. Its strong physical and chemical properties ensure reliable performance in large-scale manufacturing and infrastructure projects.

Specification Points:

Product Name: Iron Ore
Material Type: Natural Iron Mineral
Color: Dark Brown to Reddish Black
Form: Lump, Fine Powder, or Pellet
Iron Content: High Purity Grade
Moisture Level: Low Moisture Content
Usage: Steel Manufacturing and Industrial Processing
Density: High Density Material
Processing Type: Crushed, Screened, and Refined
Melting Suitability: Suitable for Smelting Applications
Storage Condition: Dry and Ventilated Area
Packaging Type: Bulk Packing or Industrial Bags
Chemical Stability: Strong and Consistent Composition
Application: Construction, Metal Industry, and Engineering Projects

This product is supplied with a focus on quality consistency, efficient processing performance, and industrial reliability for long-term operational use.

Product introduction:

Calcium is a silvery white metal that is harder and heavier than lithium, sodium, and potassium;

It melts at 815 C. The chemical nature of metallic calcium is very active. In the air, calcium is quickly oxidized and masked with an oxide film. When heated, calcium will burn and emit a beautiful glow of brick red. Calcium and cold water have a slower effect, and intense chemical reactions occur in hot water to release hydrogen (lithium, sodium, and potassium can cause intense chemical reactions even in cold water). Calcium is also easily combined with halogens,

sulfur, nitrogen, and the like.



1,product name:calcium metal

2,Shape :powder, lump and granulates

3,CAS:7440-70-2

4,Density:1.54g/cm

5,Melting point:850C

6,Boiling point:1440 C(lit.)

7,Application:Wheel keel



Product use:

At present, in the steel industry, the main use of metal calcium is to process into metal calcium particles, and then to make calcium iron wire or pure calcium wire, and finally used for steel refining outside the furnace, its role is to desulfurization, deoxidation, increase the fluidity of molten steel. Promote the rapid rise of inclusions in molten steel, generally used in the production of high-quality steel; as a dehydrating agent to produce anhydrous alcohol; in the petroleum industry, as a desulfurizing agent, in the metallurgical industry, it is used to deoxidize or

desulfurize . However, calcium compounds have a very wide range of uses, especially in the construction industry.

Wood Pellets are a high-quality biomass fuel produced from compressed natural wood fibers. They offer an efficient, clean-burning, and environmentally friendly energy source suitable for residential, commercial, and industrial heating applications. Manufactured under controlled conditions, these pellets provide consistent heat output, low ash production, and reliable combustion performance. Their compact size and uniform shape ensure easy handling, storage, and automatic feeding in compatible pellet stoves, boilers, and heating systems. Wood Pellets are an excellent alternative to conventional fossil fuels, helping improve energy efficiency while reducing waste. They are widely used for space heating, power generation, and other energy-related applications where dependable fuel performance is required.

Specifications:

Product Name: Wood Pellets
Material: Compressed Natural Wood
Form: Cylindrical Pellets
Color: Natural Wood Brown
Moisture Content: Low
Ash Content: Low
Calorific Value: High
Density: High Bulk Density
Diameter: 6 mm / 8 mm
Length: 10-30 mm
Burning Efficiency: High
Smoke Emission: Low
Sulfur Content: Minimal
Application: Pellet Stoves, Boilers, Furnaces, Industrial Heating, Power Generation
Storage: Keep in a Dry and Well-Ventilated Area
Packaging: Available in Bags or Bulk as per Requirement

Mica is a hydrated phyllosilicate mineral of aluminium and potassium with formula KAl(F, OH), or (KF) (AlO) (SiO). Muscovite can be cleaved into very thin transparent sheets that can substitute for glass, particularly for high-temperature applications such as industrial furnace or oven windows.

It is also used in the manufacture of a wide variety of electronics and as a filler in paints, plastic, and wallboard. Our monthly supply of these mineral ranges from 1000-2000MT.

Coconut shell charcoal is a high density, eco-friendly fuel obtained by burning the shell of fully matured coconuts with a limited supply of air so that they do not burn away to ash but are only carbonized. The manufacture of shell charcoal shows from the coconut shell has become a very important economic and commercial activity. Furthermore, coconut shell charcoal, which was relatively minor product in the past, has now developed into a general commercial commodity due to its intrinsic value as a raw material for the manufacture of activated carbon. Coconut shell charcoal shall be of the following two types:
Type I Coconut shell charcoal pieces
Type II Coconut shell charcoal granulated

Primary Applications
Culinary: Preferred for BBQ, grilling, and high-end restaurants due to its consistent heat and smokeless nature.

Shisha/Hookah: Highly favored by enthusiasts for its odorless, chemical-free burn that doesn't alter the shisha flavor.

Activated Carbon: Served as the primary raw material for high-quality activated carbon used in water purification and air filtration due to its microporous structure.

Industrial: Used in metallurgy for smelting gold and silver and as an eco-friendly substitute for furnace oil

Key Characteristics
Appearance: Uniformly dark black and hard with a shiny surface on broken edges.
High Carbon Content: Typically contains 75% to 85% fixed carbon, providing a steady and intense heat.
Heat Performance: Boasts a high calorific value ranging from 7,000 to 8,000 kcal/kg, nearly double that of some wood charcoals.
Low Ash & Smoke: Produces minimal ash (often <3% to 5%) and very low smoke emissions, making it ideal for indoor and outdoor use.
Physical Quality: Good quality pieces produce a distinctive metallic "ring" sound when dropped on a hard surface.

Mica is a hydrated phyllosilicate mineral of aluminium and potassium with formula KAl(F, OH), or (KF) (AlO) (SiO). Muscovite can be cleaved into very thin transparent sheets that can substitute for glass, particularly for high-temperature applications such as industrial furnace or oven windows.

It is also used in the manufacture of a wide variety of electronics and as a filler in paints, plastic, and wallboard. Our monthly supply of these mineral ranges from 1000-2000MT.

Price and Minumum Quantity fob
Price Lagos port in USD:450, Minimum Order Qty: 28 (One 40ft container) Metric Tonnes
Production Capacity: 2000 Tons (Per Year)Packaging: 50Kg Pp Bags
Sample: Available. Sample Cost Born By Buyer Payment: by confirm L/C or CAD with 30% advance payment.

Due to its chemical and physical properties, EBT sand is an important mineral demanded generally by the iron and steel making industry. In our sales we have EBT sand (2-6mm or 3-8mm grain sized) which is mainly used as electric arc furnace tap hole filler sand (EBT sand).

ES NiCrFe-2 is a nickel-based electrode for welding Inconel 600 and similar alloys, cryogenic steels (e.g. 9Ni and 5Ni steels), martensitic to austenitic steels, dissimilar steels, heat-resistant steel castings with limited weldability and so on.

The weldability is good in all positions, even in the over-head position.

Used extensively in the furnace equipment & repair / petro-chemical industries.

LPG stands for Liquefied Petroleum Gas. It is a fuel made mainly from propane and butane gases that are compressed into a liquid form for easy storage and transportation. LPG is also known as " cooking gas" or " auto gas"

LPG is a mix of light hydrocarbon gases, mainly propane C3H8 + butane C4H10. It comes from Crude oil refining and Natural gas processing.

Key properties:
Composition: Propane C3H8 + Butane C4H10 Light hydrocarbons.
State: Gas at room temp, liquid under pressure Liquefies at 20x atmospheric pressure.
Smell: Odorless naturally, but ethanethiol/ethyl mercaptan is added so leaks smell like rotten eggs.
Density: Heavier than air. Leaks sink to ground, can run along floors/drains.
Boiling point: Propane -42C, Butane -0.5C Vaporizes instantly if spilled.
Energy: ~94 MJ/m³, higher than natural gas 38 MJ/m³.
Storage: Steel cylinders/tanks. 1L liquid - ~250L gas when vaporized.
Sulfur: Almost zero sulfur = clean burning.

Key facts:
1. Source: Comes from 2 places: 1) Natural gas processing wet gas, 2) Crude oil refining as top distillate
2. Pressure storage: Unlike LNG -162C, LPG stores as liquid at room temp with just 8-10 bar pressure. Much simpler
3. Clean fuel: Zero sulfur, burns with blue flame, no soot. 50% used for cooking/heating
4. Heavier than air: LPG vapor sinks and flows along ground. Leak = explosion risk in drains/basements
5. Autogas: LPG for cars. Cheaper than petrol, but needs LPG tank + converter kit.

Grades/blends:
1. Propane: HD-5 grade, used as auto gas/vehicle fuel
2. Butane: More common for cooking in warm climates like Port Harcourt

Common uses of LPG
Cooking (gas stoves and ovens)
Heating homes and water
Fuel for vehicles (often called autogas)
Industrial applications such as metal cutting and manufacturing
camping stoves, refrigerant, aerosol propellant.

Advantages
Burns cleaner than coal or wood
Produces high heat efficiently
Easy to store in cylinders or tanks
Portable and widely available

Safety
Because LPG is highly flammable:
Store cylinders upright.
Keep them away from heat sources.
Check regularly for leaks.
Ensure good ventilation when using LPG appliances.
LPG can not be put in a clear jar like diesel, it had just boil off instantly at atmospheric pressure. It needs a pressurized steel cylinder or cryogenic vessel to stay liquid.

Dolomite as a mineral has very few uses the most common is in the construction industry. It is crushed and sized for use as a road base material, an aggregate in concrete and asphalt, railroad ballast, glass industry also used as refractory, ramming, and fettling material in steel melting shop, and as fluxing material in blast furnace.

GS are one of the major Dolomite producers in Egypt, our Dolomite is characterized by moderate percent of MgO (20 -25%), and up to 28-30% for glass manufacturing
We can supply Dolomite in lumps or powder form, as per the required micron size, and by any quantities, packages and sizes

ES NiCrMo-3 is a NiCrMoNb-based electrode for welding nickel alloys of the same or similar type,like Inconel 625, and for welding 5Ni and 9Ni steel.

ES NiCrMo-3 is also suitable for welding UNS S31254 steel.

ES NiCrMo-3 electrode is utilized for welding piping systems and reactor components in the power generation industry and for high temper-ature service in an array of other engineering applications, including petrochemical plants and furnace equipment.

ES ENiCrMo-3 is excellent for overlaying on steel where exceptional corro-sion resistance is required, such as chloride contaminated cooling water in heat exchangers, as well as offshore and marine environments.

collection of urban lighting units provided with many patterns and independent intellectual properties and many advanced technologies.

Lighting poles range are designed to give spread light distribution which makes this luminaire suitable for gardens, path ways and homes.

Lighting poles range are designed to give spread light distribution which makes this luminaire suitable for gardens, path ways and homes.

Bollards from the outdoor range , come with fabulous designs and different ranges.
IP 65
free standing luminaire
ideal for lighting path ways and gardens
available in different lengths
extremely durable.

E-sign is a series to comply building fire codes an insurance standards.
it uses less than 2 watts of power with back up battery for 3 hours.

Flood light luminaire in an elegant design is making the installation flexible and convenient, it does not only provide bright and lasting lighting but also reduce maintenance.
material: made of die cast Aluminum treated and painted with electrostatic powder coating
Lens: made of safety and tempered glass
Suspension: surface mounted