96% G-Grout UF-9 Grouting Compound Powder is professional grade material that used as crack injection grout powder. It has finer particle size. It is produced in well known manufacturing plant in a controlled environment resulting in consistent quality. It is manufactured by unique particle size distribution technique to enable finest particle size for application.
G FINE Micro FINE ULTRA FINE EROPEAN BASED FINEST FILLER
G FINE is a new generation supplementary cementitious material (SCM) with a built-in high tech content. In spite of its high fineness it does not increase water demand at the dosage range of 5 to 15 percent of normal OPC in general. In fact concrete slump is seen to be improved, due to the dense packing of cementitious material, producing low void content. The use of G FINE results in hydrated cement matrix to comprise of very small pores.
G FINE is a specially processed product based on high glass content with high reactivity obtained through the process of controlled granulation. The raw materials are composed primary of low calcium silicates. The processing with other select ingredients results in controlled particle size distribution. G FINE can also be used as a high range water reducer to improve compressive strength or as a super workability aid to improve flow.
G FINE can be used as practical substitute for Silica Fume as per the results obtained. If the advantages of G FINE are observed in the concrete mix design, the initial rate of strength development was found to be increased or similar as that of Silica Fume.
Where to use G FINE :
Residential, roads, airports, commercial building. Producing mass concrete structures and pile. In high-rise structures the concrete is to be pump easily. Low water to binder ration for high performance concrete. Precast concrete element for heavy structures precast units. To improved initial strength and increase faster . Better retention of workability and improved strength gain.
Benefits of G FINE :
The workability of the mix retention is improved Improve durability and permeability of concrete Increased strength of concrete Reduction in segregation can be observed in the mix Reduction in heat of hydration of the mix Non- toxic , eco friendly cost effective, economical solution
G-FINE
Packaging:
G FINE is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25kg plastic lined bags.
Storage:
G FINE when stored correctly has an indefinite shelf life. Like cement, G-FINE must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo Or warehouse .
Cement clinker is a solid material produced in the manufacture of portland cement as an intermediary product. Clinker occurs as lumps or nodules. We can provide Clinker in Bulk and Big Bags, depending upon the requirement. We can accept L/c, TT as a payment terms.
Cement clinker is a solid material produced in the manufacture of Portland cement as an intermediary product. Clinker occurs as lumps or nodules, usually 3 millimetres to 25 millimetres in diameter.
Portland cement is the most common type of cement in general use around the world as a basic ingredient of concrete, mortar, stucco, and non-specialty grout
Crown Portland Composite Cement is CEM-II/A-M which is a cement consisting of Clinker, Gypsum, Pulverized Fuel Ash (PFA), Blast Furnance Slag and Limestone designated by the specifications of BDS EN 197-1: 2003; CEM -II/A-M (V-S-L), 42.5 N. PCC is the most suitable cement for constructions in Bangladesh. CEM â?? II /A-M contains 80-94% Clinker, which is substantially higher than CEM â?? II/B-M containing 65 â?? 79% Clinker that provide us extra advantage in strength development and increase concrete performance.
Both slag & fly ash (PFA) are used in PCC. Percentage of SiO2 in PFA is higher than slag which is advantageous to gain more long-term strength and ensure durable concrete. This type of cement is used for large constructions all around the world and it has been used during the last few decades.
The hydration process of normal cement produces Calcium Silicate Hydrate CHS & Calcium Hydroxide Ca(OH)2. Calcium Hydroxide Ca(OH)2 does not contribute to gain strength and it is the weak part of reaction which is not suitable for concrete. Since PFA contains higher portion of reactive silica and slag contains alumina, it helps to convert Ca(OH)2 into CSH to gain further strength.
Cement Clinker, a crucial component in the production of Portland cement, is created by heating a mixture of limestone and clay in a kiln until it forms small, gray nodules. These nodules are then finely ground to produce the cement powder used in construction. Clinker's chemical composition, including calcium silicates and aluminates, determines the strength and durability of the resulting cement
Clinker, in the manufacture of Portland Cement, is a granular substance that occurs as lumps or nodules, usually in the diameter of 3 to 25 millimeters. Clinker is available in grey, powdered, or lumps. Clinker with years of experience in providing the raw materials of cement Clinker, serving our customers from leading Cement factories. We have long-lasting, trusted relationships with our customers to supply various types of clinkers required for the production of Cement. Applications * The primary use of Clinker is in the production of cement. In the cement industry, the Clinker is also known as the Portland Cement Clinker.
Origin :- Vietnam . Iran , Turkey
Portland cement is the most common type of cement in general use around the world as a basic ingredient of concrete, mortar, stucco, and non-specialty grout. It was developed from other types of hydraulic lime in England in the mid 19th century, and usually originates from limestone
Portland cement is the most common type of cement in general use around the world as a basic ingredient of concrete, mortar, stucco, and non-specialty grout. It was developed from other types of hydraulic lime in England in the mid 19th century, and usually originates from limestone
Origins : Nigeria, China ,Iran , Ghana, Italy, India
Portland cement clinker is ground to a fine powder and used as the binder in many cement products. A little gypsum is sometimes added. It may also be combined with other active ingredients or chemical admixtures to produce other types of cement including: ground granulated blast furnace slag cement
Origins : Iran, Portland, Indonesia, Vietnam, Malaysia, India, Egypt, Turkey, Pakistan, Thailand
Clinker Is A Nodular Material Produced In The Kilning Stage During The Production Of Cement And Is Used As The Binder In Many Cement Products. The Lumps Or Nodules Of Clinker Are Usually Of Diameter 3-25 Mm And Dark Grey In Colour.
Product Description:
Clinker, if stored in dry conditions, can be kept for several months without appreciable loss of quality. Because of this, and because it can easily be handled by ordinary mineral handling equipment, Clinker is also shipped to grinding plants in areas where cement-making raw materials are not available.
MAXX Powergrout 60 is a free flow non shrink high strength cement based expansive grout. it is developed by using special additives & graded filler. it is recommended for grouting with design strength up to 60 MPa.
Area of Application
Maxx Powergrout 60 is ideal for heavy machinery base plate, tie bolt holes, crack treatment core filling, bearing plates, columns in precast. It is essential to withstand static & dynamic load.
Features & Benefits
1) High early strength
2) Non -Shrink
3) Chloride free
4) Enhance durability
5) Enhanced flow properties and pot life
6) No bleeding and better mix consistency
DIRECTIONS FOR USE:
- Shake well before using.
- Keep container closed when not in use.
- Set time is the time required before joint can safely be handled.
- Cure time is the time required before joint can be pressure tested.
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go A1/A3 to A1/A2 way into fitting. If pipe bottoms into fitting it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation. Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least A1/A2 the size of the pipe diameter.
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting. Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts. Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 16 C or 60 F Longer cure time may be required for larger pipe and /or temperature is below 16 C or 60 F.
DIRECTIONS FOR USE:
Shake well before using.
Keep container closed when not in use.
Set time is the time required before joint can safely be handled.
Cure time is the time required before joint can be pressure tested.
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go way into fitting. If pipe bottoms into fitting
it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and
fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation.
Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least the size of the pipe diameter
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting.
Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts.
Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low
and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 16 C or
60 F Longer cure time may be required for larger pipe and /or temperature is below 16 C or 6
RPC-WELD PVC solvent cements have passed the following tests performed according to ASTM Standard D2564
Test Pressure
2 hour Hydrostatic Burst Test 400 psi
2 Hour Lap Shear Test 250 psi
16 Hour Lap Shear Test 500 psi
72 Hour Lap Shear Test 900 psi
DIRECTIONS:
Keep container close when not in use
Set time is the time required before joint can safely be handled.
Cure time is the time required before joint can be pressure tested
1. Cut pipe square with saw or hand cutter. Remove all burrs.
2. Check dry fit of pipe and fitting. Pipe should easily go to way into fitting. If pipe bottoms into fitting
it should be very snug.
3. Pipe and Fitting should be free of dirt, grease and other foreign materials. If necessary clean pipe and
fitting using RPC-WELD Pipe Cleaner. Primer is highly recommended for 3 and larger diameter installation.
Apply liberal coat. Primer will start softening surface of pipe and fitting thus ensuring superior joint.
4. Use applicator supplied with the can or suitable applicator at least the size of the pipe diameter
5. Apply liberal coat of cement to the pipe (equal to depth of fitting) and adequate coat inside of fitting.
Make sure there is no uncoated surface. Avoid puddling of cement, it may weaken the joint.
6. Immediately insert pipe into fitting with twisting motion. Cement should be wet. If it has dried recoat both parts.
Use sufficient force to ensure pipe bottoms into fitting.
7. Hold joint together for 30-40 seconds to make sure pipe is not pushed out longer time if temperature is low
and for larger pipes.
8. Allow 15 minutes set time before handling the assembly and 2 hours cure time if temperature is below 60 F.
Longer cure time may be required for larger pipe and /or if temperature is below 60 F.
Do not test with compressed air.
DESCRIPTION: RPC-WELD CPVC is an orange, heavy bodied, high strength, medium setting CPVC solvent cement for all classes and schedule. This cement is manufactured in the India.
APPLICATION: RPC-WELD CPVC is for use on all grade CPVC pipes and fittings. This cement may be used for potable water, irrigation drain, waste, vent, sewer and conduit. This cement can be used for HOT and COLD water applications.
PROPERTIES AND SPECIFICATIONS:
Color Orange
Appearance Liquid
Set TimeFast Medium
Cure Time Consult ASTM schedule
Exceeds ASTM F- 493 specification
Shelf Life 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units/case Units/ master
59 ml 24 192
118 ml 24 144
237 ml 24 96
473 ml 12 48
946 ml 6 24
DESCRIPTION: King PVC Solvent is a clear, medium bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: King PVC Solvent is for use on PVC pipes and fittings. This cement may be used for upto 4â??â?? pipes and fittings with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
59 ml 24 192
118 ml 24 144
237 ml 24 96
473 ml 12 48
946 ml 6 24
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION : RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Gray
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION: RPC-WELD PVC Solvent is a clear, heavy-bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This Solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units/Case Units/ master
50 ml 24 192
100 ml 24 144
200 ml 24 96
250 ml 24 96
500 ml 12 48
1000 ml 6 24
DESCRIPTION : RPC-WELD PVC Solvent is a clear, heavy bodied, high strength, fast setting PVC solvent cement for all classes and schedule. This solvent cement is manufactured in the India.
APPLICATION: RPC-WELD PVC Solvent is for use on PVC pipes and fittings. This cement may be used for all grade pipes and fittings irrespective of diameter with interference fit for potable water, irrigation, drain, waste, vent, sewer and conduit applications.
PROPERTIES AND SPECIFICATIONS:
Color: Clear
Appearance: Liquid
Set Time: Fast
Cure Time: Consult ASTM schedule
Exceeds: ASTM D2564 specification
Shelf Life: 3 years
Raw Materials from U.S.A
AVAILABILITY:
Size Units / case Units/ master
59 ml 24 192
118 ml 24 144
237 ml 24 96
473 ml 12 48
946 ml 6 24
Cement mortar is basically a mixture of cement, sand & water. It is used in various aspects of civil engineering works such as masonry, brickwork, plastering, flooring etc. There are two types, dry mortar and wet mortar. Dry Mortar primarily constitutes of only sand and cement.
For price, specifications and other details please contact us.
A cement is a binder, a chemical substance used for construction that sets, hardens, and adheres to other materials to bind them together. It is most widely used material in existence and is behind only water as the planet's most-consumed resource.
White Portland cement or white ordinary Portland cement is similar to ordinary, gray Portland cement in all aspects except for its high degree of whiteness. Obtaining this color requires substantial modification to the method of manufacture, and because of this, it is somewhat more expensive than the gray product
OPC is the most commonly used cement in the world. PPC means Pozzolanic Portland Cement. Pozzolans are siliceous material than can be added to concrete mixtures, to potentially lower the mix cost without harming the performance characteristics
We are working with highly experienced packaging experts and they make every endeavor to meet the personalized and standard requirements of the clients. We sternly make our product safe from external factors. We, being a customer centric organization, make sure that the transactions are carried out by the professionals so as to avoid any kind of confusion. We sternly maintain payment records for the satisfaction of our clients.
India is World’s Second largest Cement Producer. India is contributing tremendously to the Supply of Cement across the Globe. The Capacity of Indian market to produce and supply cement is increasing at swift pace.
We source the best quality and from the best brands. We supply OPC, PPC, Slag cement, White Cement and Sulfate Resisting Cement.
BuildWell Colour Putty is a wall putty with added advantage of shades like Pink, Yellow, Green and
Off-White, especially developed as a base coat to provide smooth finish on plastered surface, and hence
ideal for expensive paint application because paint saving can be up to 50%.
It contains finest quality minerals, polymers, white cement and pigments. It can also be used for low end
application like basement parking lot, etc as 'Final Finish'.
Benefits :
- Reduces paint consumption
- Avoid frequent repainting.
- Cost effective.
- Aesthetic look for ceiling and Interior walls.
- Ease of use at site.
Advantages :
- True colour tone of the paint is
maintained, primer is not required.
- Protects expensive paint from dampness,
peeling off, and flaking.
- Makes paint durable.
- Suitable for Interior.
- Paint finish is superior.
Offering all branded finest cement All types of cements are available
Price of product ( USD price or FOB price) -
20 USD - 35 USD per Bag
depending upon the type and
grade
Product origin - Tamil Nadu-India
Building and Construction (All Grades)
Certification as per buyer requirement
Place of Orgin : Tamil Nadu (India)
Port of Loading : Chennai Port
Payment Term : Initially, 50% Advance and
remaining 50% irrevocable LC
Delivery Time : 20 working days
Minimum Order : 20 Feet Container
Packaging : 25-50 Kg Bag (1 Sack)
Clinker is a nodular material produced in the kilning stage during the production of cement and is used as the binder in many cement products. The lumps or nodules of clinker are usually of diameter 3-25 mm and dark grey in color. It is produced by heating limestone and clay to the point of liquefaction at about 1400�°C-1500�°C in the rotary kiln. Clinker, when added with gypsum (to control the setting properties of cement and ensure compressive strength) and ground finely, produces cement. Clinker can be stored for long periods of time in a dry condition without degradation of quality, hence it is traded internationally and used by cement manufacturers when raw materials are found to be scarce or unavailable.
Product Specifications
Color White
Material PP
Customized color Size
Use Industrial
Feature Recyclable
Product Type Bags
Price 9 INR/Bag
Minimum Order Quantity 100000 Bag
PP Cement Bag Trade Information
Payment Terms Cash in Advance (CID)
Supply Ability 5000000 Bag Per Month
Delivery Time 15-20 Days
Main Export Market(s) North America South America Eastern Europe Western Europe Central AmericaMain
Domestic Market All India
Product Description
PP Cement Bag has the most essential component for mixing concrete in the cement bag. Calcined limestone and clay are combined to create a fine powder that is used to make cement. In order to create concrete, it is then utilised to combine water and aggregate. It is made up of three elements known as virgin material, master batch, and UV coating which makes it durable and strong. We offer this PP Cement Bag at an affordable price in the market.
PP Cement Bags
We are Leading Manufacturer, Supplier and Exporter of Cement Bags which is durable, reliable and cost efficient packaging options for different purpose.
Cement Bags
Ekta Polypack LLP is a renowned PP cement bag manufacturer & supplier in India. We deal with all kinds of PP woven bags including Block bottom cement bag and multi color gusseted cement bag.
PP cement bags are mostly used for packaging in the cement industry. These bags are manufactured using high-quality virgin material, master batch and UV coating.
We manufacture the cement bags which have high strength alongside increased tear resistance to make these bags secure against rough handling. These Innovative and light-weighted PP cement sacks are immune to humid weather and protect against moisture which in turn, leads to the prolonged-time period of the packed products. We also offer customized PP cement bags as per the specifications provided by the client.
We provide the topmost first-class Fly Ash Bricks made with the aid of stone dust, lime, cement to make them powerful enough. Our Fly Ash Bricks are gentle in weight which makes them exceptional from other merchandise. Due to their excessive force there is no breakage in them for the period of transport and use. They�¢??ve a low water penetration which reduces the seepage of water via the bricks. We�¢??re completely devoted in offering excessive nice Fly Ash Bricks. We now have developed a state of artwork infrastructure to reward the enterprise compliant variety of fly ash bricks providing advanced. The superb insulation of Fly Ash Brick supplies a comprehensive constructing material solution for indoor and outside construction. They�¢??re quick to put in and can form up any constructing assignment actual fast. They may be able to be cut, routed or sanded to fit in the various standards of a construction website online. They're apt for urban construction that has a sharp temperature upward thrust gradient. We experiment the blocks to make certain highest force.
