Sodium Silicate is an inorganic chemical wherein its formulations vary depending on amount of Na2O and SiO2. This compound is well known as Water Glass in industries.
We mainly supply following types of Sodium Silicate:
Fiberglass Reinforced Plastic grating is made by interlacing glass fibers and molded by
resin casting. With its many rectangular and square spaces, it provides two-dimensional
homogeneous mechanical characteristics.
The typical size of the product is - 1220 x 3660 mm. However, it is available in different mesh
sizes and thickness
- Advantages
- Easy to assemble
- High Load-bearing capacity
- Easy to install and maintain / repair
- Durable in harshest environments
- Suitable for ventilation and natural lighting
Fiberglass really is made of glass similar to that in windows or kitchen drinking glasses. To manufacture fiberglass, glass is heated until molten, then forced through superfine holes. This creates glass filaments that are extremely thin so thin, in fact, that they're best measured in microns
Our HighFlux Aruvi series hollow fiber Cartridges have the following salient features
Membrane Packing - About 50 square meter Membrane Area
Pre-filtration - Suitable Pre-filter for RO; Municipal Water & Industrial Wastewater
Low Pressure - Around 2 bar Pressure Operation
Higher Permeate - up to 1-3 cubic meter Permeate (vary depends on actual conditions)
Backshwash - Easy backwash process and cleaning
FP-02
Description
Insulated 16mm Rod Pin with a metal point and metal cap, which allows it to be struck with a hammer. Each Insulated Road Pin is flash tested to 10,000V.
Insulated non conductive road pins help reduce the risk of electric shock from buried cables. Manufactured from 12mm fibreglass rod with forged point, allowing it to penetrate a variety of surfaces.
Sizes Available : 16mm x 600-1500mm.
336 Fiberglass Products Suppliers
Short on time? Let Fiberglass Products sellers contact you.
FP-01
Description
Insulated 12mm Rod Pin with a metal point and metal cap, which allows it to be struck with a hammer. Each Insulated Road Pin is flash tested to 10,000V.
Insulated non conductive road pins help reduce the risk of electric shock from buried cables. Manufactured from 12mm fibreglass rod with forged point, allowing it to penetrate a variety of surfaces.
Sizes Available : 12mm x 600-1500mm.
Attachments Available : Metal & Plastic Point & Plastic Hook End & Metal Cap.
Outer diameter and length can be made by customers specific requirements.
Features
Non-Corrosive
2. Dimensionally Stable
3. Lower Life Cycle Cost
4. Flame Retardant
5. Easy to Fabricate and Install
6. Electrically Non-Conductive
7. Lightweight/High Strength
8. Resists Insect Damage
9. High Impact Strength
10. Low Water Absorption
11. Greater Flexural Strength Than Timber
12. Non-Leeching
Physical,mechanical and dielectric property should follow the table below:
Technical requirement
Normal Diameter Thickness Length Tolerance Allowed
inside diameter outside diameter Length
30~70 3~20 500 ±0.3 ±0.3 ±1
70~150 3~20 1000 ±0.5 ±0.5 ±2
150~550 10~100 2800 ±0.5 ±0.2 ±2
Physical and mechanical parameters Physical and mechanical parameters
Index Name Unit Index Index Name Unit Index
Density g/cm3> 1.80 Density g/cm3> 1.80
Water absorption % 0.15 Water absorption % 0.15
Intensity of curvature(circling direction) Mpa 400 Intensity of curvature(circling direction) Mpa 400
Intensity of compress Mpa 98 Intensity of compress Mpa 98
Voltage vitality on parallel layer at normal state for 5min Kv 25 Voltage vitality on parallel layer at normal state for 5min Kv 25
Voltage vitalityon vertical layer in the oil at 90C for 5min MV/m 12 Voltage vitalityon vertical layer in the oil at 90Cfor 5min MV/m 12
Enquire Now
Epoxy fiber glass tube is made by good quality glass fiber steeped into epoxy resin of thermo-stability, which is high quality material as making high voltage electric devices, such as breakers, thimbles, mutual inductors, zinc oxide arresters, etc.
FRP-02
Description
This product is widely used in composite suspension long rod insulator, composite post insulator, composite cross-arm insulator, composite drop switch insulator, disconnector, wind deflection of composite insulator, spacer composite insulator, composite insulator for electric railway overhead contact line and other composite insulator industry. The product quality we manufacture for our clients is said to meet IEC 61109 DL/T 810 GB/T 13096-1 GB/T 775.3 JB/T 5892-91 and other related technical requirements.
We specialise on fiber glass products, which include the fiber glass rods, fiber glass tubes, fiber glass sheet as well as various fiber glass profiles like the fiber glassI beam,fiber glass channel,fiberglass angle, etc. Pultrusion process is a kind of method to make continuous composite profiles, which use the twist-less roving on the creel with other continuous reinforced composites, polyester surface mat to proceed the resin impregnation, and then keep the forming mould at certain section, makes the continuous deepening after curing in the intramode. Thus,the pultrusion products come out by this automatic production process. The common products like round rods, round tubes, flat bars, square tubes, angles, U-bars, joist steels,T profiles and other kinds of special profiles.
Specification
Specification Item
Density 2.1g/cm3
Water Absorption <0.05 %
Tensile Strenth 1200 Mpa
Bending Strenth 900 Mpa
Flexural Strength in thermal state 300 Mpa
Water Diffusion Test (12 KV)1min <1 mA
Dye penetration pass after 15mins
FRP-01
Description
Epoxy Resin Fiberglass rod is adopt glass fiber steeped into epoxy resin pultrusion under high temperatures, which as features light weight,stable mechanical performance,high insulation performance in the range of 10KV to 1000KV.
The tensile strength can up to 1360Mpa
High-temperature rod,Acid-proof rod. This product can be used as the core rod of composite insulator, the vaulting pole of the arresters and the insulant of other high mechanical and electrical appliances.
Insulating Solid Rod is made of ECR glass reinforced epoxy resin.We use continuous pultrusion process .The products comply to the BS standards. Insulator core rods also are also called fiber glass rod, FRP rod, GRP rod, fiber glass bar, Insulation rod, fiber glass stick and so on. It is widely used in the electrical industry, our fiber glass epoxy resin rod products be exported to European Countries like France, Romania, Hungary and United Kingdom, and other countries like Vietnam.
Specification
Dimeter of rounded rod: D16, D18, D20, D24, D26, D28, D30, D32, D34, D36, D40, D46, D50,D53, D55, D60, D68, D70, D80, D90, D96, D100, D110, D150 and so on
Length of Round rod: 200mm to 6000mm, itâ??s depend on customer's request.
Also, can open new mould according to customer's demand.
Specification Item
Density 2.1g/cm3
Water Absorption <0.05 %
Tensile Strength 1200 Mpa
Bending Strength 900 Mpa
Flexural Strength in thermal state 300 Mpa
Water Diffusion Test (12 KV)1min <1 mA
Dye penetration pass after 15mins
The hollow fiber ultrafiltration membrane we offer adopts modified PVDF as raw material. The PVDF is processed with hydrophilization treatment; our HF membrane for ultrafiltration has higher water flux and better antifouling property. MEMFILL has various types of membrane which has different molecular weight cut off (MWCO) up to ~100,000 Dalton; Our product can be used for the removal of microorganism, colloids, algae and other impurities that may cause turbidity
Good anti-fouling performance, high water flux, stable permeate water production, long service life;
Outside-in filtration or Inside out type is possible, it can stand bad water quality condition
Combined air and water backwash together, high flux recovery rate, so easy to clean
Excellent chemical stability and high antioxidant ability
Low-pressure operation; save electricity and energy. Operation pressure 0.30 MPa
The hollow fiber ultrafiltration membrane we offer adopts modified PES as basic raw material. The PES is processed with hydrophilization treatment; our hollow fiber membrane for ultrafiltration has higher water flux and better antifouling property. MEMFILL has various types of membrane which has different molecular weight cut off (MWCO) up to ~ 100,000 Dalton; our product can be used for the removal of microorganism, colloids, algae and other impurities that may cause turbidity
Suitable commercial cartridge with high performance
Higher output flux with low pressure operation
Easy to clean with low cost operation
As a pre-filter which is highly suitable for commercial RO plant
Easy back wash process
Permeate rate is from 100 to 200 LPH
FRP-03
Description
Specification Item
Density 2.1g/cm3
Water Absorption <0.05 %
Tensile Strenth 1200 Mpa
Bending Strenth 900 Mpa
Flexural Strength in thermal state 300 Mpa
Water Diffusion Test (12 KV)1min <1 mA
Dye penetration pass after 15mins
characteristics
1. Light weight, high strength, corrosion resistant
FRP is a good corrosion resistant material, and has good resistance to air, water, acid, alkali, salt and many kinds of oils and solvents.Has been used in all aspects of chemical corrosion protection, is replacing carbon steel, stainless steel, wood, nonferrous metal and so on.
2. Good electrical performance
It is an excellent insulating material used to make insulators.High frequency can still protect good dielectric property.Microwave transmittance is good and has been widely used in radome.
3. Good thermal performance
FRP has low thermal conductivity and is 1.25~ 1.67kj /(m�· H �·K) at room temperature. It is only 1/100~1/1000 of metal. FRP is an excellent thermal insulation material.It is an ideal thermal protection and ablative material under the condition of instantaneous super high temperature, which can protect the space vehicle from the erosion of high-speed airflow above 2000â??.
4. Good design ability
(1) according to the needs, flexible design of a variety of structural products, to meet the use of requirements, can make the product has a good integrity.
(2) can be fully selected materials to meet the performance of the product, such as: can be designed to corrosion resistance, resistance to instantaneous high temperature, a direction of the product has special high strength, good dielectric, and so on.
Application: Electrical insulation
Technique:Pultrusion
Material: Fiberglass Yarn and Expoy Resin
Color: Any
Size: S22.5mm,S25mm,S28mm,S32mm,S36mm and length as customer's request.
E-glass Also Known as Electrical Glass is the
Standard Glass Composition Used for Most Glass
Fibers. It is Made From the Oxides of Silicon,
Aluminum, Calcium, Magnesium, and Boron.woven Roving is a Bidirectional Fabric Made by
Interweaving Direct Roving. Woven Roving is
Compatible With Many Resins, Such as
Polyester, Vinyl Ester and Epocy Resins. Woven
Roving is a High-performance Reinforcement
And Widly Used in Processes Such as in Hand
Lay-up, Molding, and Pultrusion for the
Production of Boats, Automotives Parts,
Furniture, Sport Facilities and Other Frp
Products
