A high solid two pack, epoxy- polyamide resin system in combination with zinc phosphate pigment giving excellent drying, adhesion, anti-corrosive, flexibility
and great surface tolerance against strong impact.
Exterior Wood Stain is based on translucent pigments dispersed in suitable solvents and in turn protect exposed exterior surface from sunlight, rain, fungal attack.
It shows excellent detailing of the wood substrate and increases the life of clear topcoat
A two-pack polyurethane quick drying primer cum surfacer with excellent filling & sanding
properties for application on wood (hard & soft) & wood substitutes like particle board,
veneer, plywood etc. The formulation contains mixed isocyanate hardeners, inert &
smooth sanding extenders. When used in combination with Maxiwood 2 PK PU Topcoat,
the product gives an extremely rich finish. Presence of plasticizer in the formulation of
Maxiwood 2 PK PU Primer Surfacer make the product flexible enough to withstand woods
dimensional variation thus enhancing adhesion.
A quick drying two pack polyurethane super gloss topcoat for application over wood & wood substitute with excellent gloss & finish.This is a higher solid formulation hence a single coat application over sealer is adequate for low grain profile substrate. On full
cure the product forms a very hard & flexible film with outstanding light fastness, chemical resistance & mechanical properties including mar /scratch resistance guaranteeing a long-term protection of wood.
A quick drying two pack polyurethane clear silk-matt /matt topcoat for application over wood & wood substitute with excellent smooth & silky finish. On full cure the product forms a very hard & flexible film with outstanding light fastness, solvent & chemical
resistance & mechanical properties including mar /scratch resistance guarantying a long-term protection of wood.
A quick drying two pack polyurethane sanding sealer for application over wood & wood substitute with excellent sealing & sanding property. The product has high penetrating power & superior filling property enabling it to perform as filler cum sealer Single coat application is adequate for low grain profile substrate. On full cure the product forms a tough flexible film with outstanding chemical resistance & mechanical properties & can withstand dimensional variation of wood due to moisture ingress. When used in combination with Maxiwood PU Gloss, Silkmatt/Matt Topcoat the system gives a very rich finish with excellent resistance properties.
A quick drying nitrocellulose primer cum surfacer designed for wood or wood substitutes. The product has excellent filling & sanding property in addition to its protective value. Quicker drying feature along with superior filling & sanding properties make it ideal for high out-put requirement as well as rich finish when
used in combination with Maxiwood NC pigmented topcoat.
Two-component Air Drying Acrylic Aliphatic, Non Yellowing polyurethane finish coating.
Recommended Use :-
This product has excellent weathering resistance additionally it offers excellent resistance to various industrial chemical fumes and splash. This product is recommended as topcoat with suitable primers and undercoats for use in High Chemical & Saline atmosphere for better aesthetics and corrosion resistance in Chemical, Fertilizers, Petrochemical, industrial plants and also for premium industrial equipments. Not recommended for immersion application.
Physical Data
COLOUR : Industrial Shades
FINISH : Glossy / Semi-glossy
SOLIDS BY VOLUME : 40 + 3% (Depends on shade)
THEORETICAL SPREADING RATE : 13.33 sq.mt / ltr @ recommended DFT of 30
FLASH POINT : Base : Above 23 C Hardener : Above 23C
DRYING CHARACTERISTICS (At 300 C & 65% Relative Humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being a topcoat, which is applied over, primer or intermediate coats, the surface should be free from oil, moisture, dust and dirt. Aged epoxy / PU coating should be roughened by emery paper grade 400 / 600 for better bonding.
Application Data :-
MIXING RATIO : Base: Hardener - As per our recommendations
APPLICATION : By Brush / By Conventional Spray / By Airless Spray
THINNER : Type 290
POT LIFE : 4 hours min at 30C
RECOMMENDED DFT : 30- 40 .
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Recommended Use :-
This product is a topcoat along with recommended undercoats for use in chemical plants, fertilizer plants, petrochemical and pharmaceutical complex, power plants, cement plants, steel plants, heavy chemicals and off-shore and on-shore industries.
It is recommended for very high chemical resistance and for areas not exposed to direct sunlight. Product is also recommended for application over suitable primer for OEM industry.
Physical Data
COLOUR : Assorted shades
FINISH : Glossy / Semi glossy / Matt
SOLIDS BY VOLUME : 40 ± 3% (Depends on shade)
THEORETICAL SPREADING RATE : 13.33 sq.mt / lt at recommended DFT of 30 µ
FLASH POINT : Base : Above 23 C Hardener : Above 23 C
DRYING CHARACTERISTICS (At 30�° C and 65% Relative humidity) : SURFACE DRY : 30 minutes max HARD DRY : Overnight FULL CURE : 7 DAYS.
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
The surface of primer or intermediate coats, over which this product is applied as topcoat, should be free from oil, moisture, dust and dirt. Aged coatings should be roughened by emery paper grade 400 / 600 for better bonding.
Application Data :-
MIXING RATIO : Base : Hardener (As per our recommendation)
APPLICATION : By Brush / By Conventional spray / By Airless Spray
THINNER : Type 290
POT LIFE : 3 hours min at 30 C
RECOMMENDED DFT : 30-40 µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be applied over Epoxy and Polyurethane primers, intermediate coats and topcoats.
Recommended Use :-
Recommended over putty / primer applied surfaces for better gloss retention and aesthetics in topcoats.
Physical Data :-
COLOUR : Grey, White
FINISH : Egg Shell to Matt
SOLIDS BY VOLUME : 40 �± 3%
SPREADING RATE : 13.3 sq.mt / ltr at recommended DFT of 30 �µ
FLASH POINT : Base : 23�°C Hardener : 23�°C
DRYING CHARACTERISTICS (At 30�°C & 65% Relative Humidity) : SURFACE DRY : 20-30 minutes. HARD DRY : Overnight. FULL CURE : 7 Days
SHELF LIFE : BASE : 6 months HARDENER : 6 months
Surface Preparation
This being intermediate, it is applied either over primer. The surface should be free from moisture, oil and dust before application. In case of aged epoxy / PU coating or exceeded over coating, the surface should be sufficiently roughened prior to painting.
Application Data :-
MIXING RATIO : Base: Hardener ( As per our recommendation)
APPLICATION : By Brush/ By Conventional Spray / By Airless Spray
THINNER : Type 290
POT LIFE : 4 hours min at 30�° C
RECOMMENDED DFT : 30 -35 �µ.
OVERCOATING INTERVAL : MIN : 8 hours MAX : 24 hours
COMPATIBILITY : Can be top coated by PU, epoxy, Chlorinated rubber and synthetic enamel paints. Compatible with Epoxy and zinc rich primers.
SAFFRO MELLOW COATINGS & RESINS MELLOWTEX RUSTIC/DHOLPURI/BUBBELS is a textured finish composed of high quality durable acrylic modified resin specially designed as an intermediate coating. RUSTIC imparts a super premium look to the walls.
BENIFITS :-
Hides Fine Cracks
It hides surface undulations and fine cracks.
Tough Textured
The tough texture finish lasts for long and ensures low maintenance.
Plaster Protection
It increases the life of plaster by protecting it from wind driven rain.
UV Resistance
It has excellent UV resistance and adhesion.
Anti-algal Formula
It resists fungal and algal growth when applied as system, with the recommended top coat.
Technical Information :-
Drying time: Surface dry time 30 - 60 min.
Flash point IS101/1987 Part 1, Sec 6: NA.
Coverage :-
Pre-painting Steps
Plaster New masonary surfaces must be allowed to cure completely. It is recommended to allow 28 days as the curing time for new masonary surfaces.
Cleaning
Surface should be free from any loose paint, dust or grease. Growths of fungus, algae or moss should be removed by wire brushing and water. When the underlying surface exhibits chalkiness, in spite of thorough surface cleaning, use Saffroâ??s Exterior Primer.
How To Apply :-
On normal masonary surface by a trowel spatula to obtain an even coating of 1 to 1.5 mm ,2 coats 2 to 2.5 sq.ft/kg**
(**Actual coverage may very from the quoted coverage due to factors such as method and condition of application and surface roughness and porosity.)
Filling For Holes & Dents :-
In case of dents and holes use Saffro Mellow Coatings & Resins SUMO Acrylic Wall Putty or white cement and fine sand in the ratio 1:3.
Saffro Mellow Coatings & Resins,MELLOW TEX RUSTIC should not be applied on surfaces / substrates that are subjected to continuous seepage or dampness.
Enhance your space with our professional-grade acoustic spray, designed to reduce noise and control reverberation in open or irregularly shaped areas. Ideal for ceilings and walls in commercial, industrial, or residential settings, this seamless sound-absorbing coating blends effortlessly with any architecture.
Our company specializes in the production of Ceramic tile adhesive and water-resist paint/waterproof glue, we have tile adhesive waterproof Acrylic Emulsions and Putty powder
Hope to establish a cooperative relationship with you.
Odorless, acrylic-based primer, antibacterial, antifungal, penetrates deep into the surface, strengthens the outer layer. Reduces paint consumption, as the ability of the surface to absorb paint decreases. Used for painting and puttying.
Per canister 10L
4S Spray Paint is a multipurpose use Spray Paint available in different colors with quick dry technology & gives perfumed glowing finish & can be easily used on any office equipment, household appliances, glass, furniture, car, bike, etc. to give them new look.
