Designed for extending the range of 2.4GHz wireless radio devices, the booster amplifier is particularly effective when used with Direct Sequence or Frequency Hopping Spread Spectrum radio modems . The unit provides the transmit power gain as well as receive signal gain.
Proprietary in-house MMIC design allows sensing of input power level and protects itself against over power or reverse power operating conditions.
Feature:
• Strengthen radio signal to Increase the effective range and coverage area for Wi-Fi communication
Save wiring costs, easily build a wireless infrastructure for home or business use
Make broadband wireless application in possible coverage
No software required, easy to install
Specification
Frequency Range 2.4GHz
P1dB 33dBm
Linear Pout 26dBm (@5.5%EVM) , 64QAM
Tx Mode Turn on Power > 2dBm
Tx Gain 13~17dBm
Rx Gain 8~12dBm
Turn on Power > 2dBm
Tx Gain 13~17dBm
Rx Gain 8~12dBm
Rx Noise Figure 3.0dB
VSWR, input/output < 2
DC supply 9~12V
Operating temperature -40~+70 oC .
180*78*60 bag packing.
110 Amplifiers Suppliers
Short on time? Let Amplifiers sellers contact you.
Description:
WLAN-2300-1W is an indoor solution 1W bi-direction Booster designed for 2.4GHz wireless LANs. This unit comes with an easy plug-and-play installation, which works together with an indoor Wireless Access Point to improve its operation range and performance. In certain conditions the unit is able to double the range of the wireless device. The unit extends signal range and can eliminate the use of an additional radio with its associated data line, power outlet, signal interference, and setup headaches.
The unit is the fast and easy way to extend your signal range in any environment. The unit is ideal for use with 2.4 GHz frequency hopping or direct sequence spread spectrum radio modems and 11 mbps IEEE802.11b devices.
The amplifiers increase range by providing transmit gain as well as low-noise receive gain. This receive gain increase the receive sensitivity of wireless LAN Access poing. Full output power of 500mW is achieved with only 32 mW input into the Booster.
Specifications:
Operating range : 2400-2500MHz
Operating mode : Bi-directional, half-duplex Time Division Duplex Senses RF carrier from Transmitter and automatically switches receive to transmit mode
Connector Type: SMA Receptacle (50 ohm)
Transmit gain : 15dB (Adjustable)
Input Trigger Power: 5~20 dBm
Optimal Input Power: 9~13 dBm
Receiver Gain: <12 dBm
Noise Figure: 3.5dB typical
Frequency Response: ¡À 1dB over operating range
Power Adaptor: 5~7V /DC 105~240V for AC Adapter
Operating Temperature: -20 to 70 ¡ãC
Operating Humidity: Up to 95% relative humidity
Material: Cast Aluminum
Package Weight: 560g.
Due to the diversity of specifications, it is impossible to display all products. If you have requirements for parameters such as frequency, power consumption, insertion loss, connector type and size, please visit our website, including product images, design drawings, testing machine reports, etc. In addition, in order to save your precious time, you can contact us directly to tell us the parameters and requirements of the products you want to customize. We will recommend a variety of customization schemes for you to choose according to the process and cost.
The Satellite Phone Indoor Amplifier Device is a device let your Inmarsat or Thuraya satellite phone can normally use in the room. (used in the boat, vehicle, building etc). Install this device with our special outdoor antenna and omni indoor antenna, making you keep in touch with others freely even in the room, you can call out and receive the incoming call even in the room, no need go out to search the satellite signal and wait for register, and at same time, the device can support up to 100 sets satellite phone communication at same time in the room which cover up to 120 square meters.
The basic principle of this device is that the outdoor antenna receives the downlink signal from the satellite (Inmarsat or Thuraya), through high selectivity band-pass filter to well isolate the passband signal, after amplifying by integrative power amplifier, then transferred by indoor antenna, meanwhile, on the way of uplink path, signal of satellite phone in the coverage area is transmitted to the satellite after disposing by uplink amplifying link path by same working mode.
For the Inmarsat and Thuraya satellite network system, downlink signal including: satellite and GPS L1 2 signal. The device has Automatic Level control ( ALC )System, automatic control the gain according to the circumstance.
Features:
-Keep your Satellite phone on communication status even in the room. Avoid miss coming call when you are in the room. And also you no need going outdoor for searching the satellite signal.
-The device can suitable for Inmarsat Isatphone Pro, Thuraya SO-2510, SG-2520, Thuraya XT etc models, and also GPS.
-Keep your satellite phone can move freely, unlike Fixed Satellite phone which canâ??t move, and also you can freely hand carry your satellite phone when need go out.
Application Range:
Boat driving room;
Emergency Vehicles;
Remote mine;
Earthquake or other emergency response administration;
Remote country where there dont have GSM mobile phone signal areas.
EDFA Optical Amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). Integrated VOA can be automatically adjusted to achieve smooth gain spectrum. It can amplify the C-Band signal with or w/o middle stage access (MSA), which brings great flexibility for the network application.
FUNCTIONï¼?
C-band optical signal overall amplification
Covering the wavelength range of 1528 ~ 1565nm
Support systems to achieve different cross-section radio repeater transmission
HIGHTLIGHT:
Wide operating wavelength range:1528nm~1565nm
Three Optical Amplifier C-Band applications: Booster , In-line, Pre-amplifier
Low noise figure: typical: 5dB
Excellent gain flatness
Multiple operating modes:
AGC adjustable Gain
APC output is adjustable
ACC voltage adjustable
Mid-stage access for DCM or OADM
Optional OSC channel for remote management
MON port, on-line monitoring optical power and OSNR
Many model options serve all the traditional amplifier applications in an extended optical link: booster, in-line, and pre-amplifier.
A booster amplifier operates at the transmission side of the link. It features high input power, high output power, and medium optical Gain . Boosters are designed to amplify aggregated optical input power for reach extension.
An in-line amplifier operates in the middle of an optical link. It features medium to low input power, high output power, high optical Gain , and a low noise figure. In-line amplifiers are designed for optical amplification between two network nodes on the main optical link.
A Pre-amplifier operates at the receiving end of an optical link. It features medium to low input power, medium output power, and medium Gain. Pre-amplifiers are designed for optical amplification to compensate for losses in a demultiplexer located near the optical receiver.
Some EDFA Models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss. The design of these models maximizes the DCM benefits to increase deployment flexibility. New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology.
HTF launched SOA series optical amplifier products can be 1290nm ~1320nm wavelength range to achieve amplification. It can be easily used in 100G transmission system, the maximum can support 160G/s rate. SOA optical amplifier can be used for booster amplification, pre-amplification and other occasions.
O-band optical signal overall amplification
Covering the wavelength range of 1290 ~ 1320nm
100G 1310nm signal amplification
Support O-band, 1290 ~ 1320nm band amplification
Output power up to 10dBm
100G 1310nm signal amplification
Support APC
Low noise, high gain
One board supports up to 2 channels of signal amplification
EDFA optical amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). This is a highly integrated EDFA, and the large module supports Dual amplifier with two independent gain units .
Wide operating wavelength range:1528nm~1565nm
Dual amplifier contains two independent gain units
Low noise figure: typ 5dB
Excellent gain flatness
Multiple operating modes:
AGC adjustable Gain
APC output is adjustable
Optional OSC channel for remote management
MON port, on-line monitoring optical power and OSNR
EDFA optical amplifier module provide multi-function, low noise, Erbium-Doped Fiber Amplifier (EDFA) solutions, The amplifier module can be operated at constant gain (Automatic Gain Control AGC), constant output power (Automatic Power Control, APC). This is a highly integrated EDFA, and the large module supports Dual amplifier with two independent gain units .
Wide operating wavelength range:1528nm~1565nm
Dual amplifier contains two independent gain units
Low noise figure: typ 5dB
Excellent gain flatness
Multiple operating modes:
AGC adjustable Gain
APC output is adjustable
Optional OSC channel for remote management
MON port, on-line monitoring optical power and OSNR
With the application of long-distance systems becoming more and more extensive, our company's self-developed middle stage access (MSA) EDFA, middle stage access (MSA) EDFA can effectively solve the insertion loss caused by DCM and OADM, offset the DCM and OADM bands. The resulting insertion loss reduces the additional degradation of the system OSNR.
C-band optical signal overall amplification
Covering the wavelength range of 1528 ~ 1565nm
Support systems to achieve different cross-section radio repeater transmission
Wide operating wavelength range:1528nm~1565nm
Low noise figure: typ 5dB
Excellent gain flatness
Multiple operating modes:
AGC adjustable Gain
APC output is adjustable
ACC voltage adjustable
Mid-stage access for DCM or OADM
Offset the insertion loss introduced by DCM
Reduce the additional degradation of system OSNR
Optional OSC channel for remote management
MON port, on-line monitoring optical power and OSNR
Middle stage access (MSA) EDFA models include an additional mid-stage port designed for insertion of a Dispersion Compensation Management (DCM) unit without its inherent insertion loss.
The design of these models maximizes the DCM benefits to increase deployment flexibility.New placement options require fewer amplifiers in the link, and they can open the door to applications that were not possible with older technology.
Single Fiber Bidirectional EDFA Amplifier models include a Red and a blue port designed for single fiber DWDM Solution. The design of these models is used for single-fiber DWDM transmission systems.
C-band optical signal overall amplification
Covering the wavelength range of 1528 ~ 1561nm
Support systems to achieve different cross-section radio repeater transmission
Operating wavelength range:
Blue: 1528nm~1543nm
Red: 1547nm~1561nm
Low noise figure: typ 5dB
Excellent gain flatness
Multiple operating modes:
AGC adjustable Gain
APC output is adjustable
ACC voltage adjustable
Mid-stage access for DCM or OADM
Offset the insertion loss introduced by DCM
Reduce the additional degradation of system OSNR
Flexible insertion of DCMs at different distances
Optional OSC channel for remote management
MON port, on-line monitoring optical power and OSNR
Single fiber bidirectional EDFA amplifier include an Red and blue port,
Red optical amplifier include an blue out port and blue in port, Red optical amplifier Amplify red optical signal, blue out port and blue in port are used to access the amplifier to amplify the blue optical signal.
Blue optical amplifier include an red out port and red in port, Blue optical amplifier Amplify blue optical signal, red out port and red in port are used to access the amplifier to amplify the red optical signal, Blue: 1528nm~1543nm. Red: 1547nm~1561nm.
