Model name: H1.3D1
3-channel with built-in 2in-3out, DSP is fm Germany.
channel-1: 250W@8ohms, 500W@4ohms; RMS
channel-2: 1200W@8ohms, 2300W@4ohms;RMS
channel-3: 120W@8ohms, 2300W@4ohms;RMS
Size:150mm X 431mm X 70mm (WXLXH)
Please check detail pictures on our website http://www.ad-power.cn.
The vp series power amplifier offers clean, reliable power in a durable enclosure. If you need professional amplification performance, the vp series is perfect for delivering pure, consistent wattage night after night.
With six models power upto 1200 watts, the vp series is ideal for powering pa systems and dj rigs. To ensure seamless, reliable performance, the amp features variable-speed cooling fans for thermal stability, along with short-circuit, thermal, over current, thermal protection.
For connecting convenience, the vp series boasts xlr and speakon &banana binding post outputs. The unit also provides front panel indicators for signal, limit, protect and power, plus level controls for channels 1 and 2. Selectable modes for stereo and mono bridge give you even more flexibility.
Selectable output power range to drive professional loudspeakers without clipping
Variable-speed cooling fan for thermal stability and reliability
Xlr balanced inputs and speakon &banana binding post outputs
Limiter indicator for amp output protection
Stereo and mono bridge
Variable speed fan for low noise
Comprehensive front panel indicators including signal, limiter, protect and power
Dc output protection and short circuit protection
Frequency response 10hz c 50khz at 1.5 db
Total harmonic distortion: less than 0.05%
Input sensitivity & impedance: 0.775v
Signal to noise (20 hz - 20 khz) > 95db
CATV amplifier
Features:
With push pull with return path options
Forward : 47-862/65-862
Return: 5-25/30/42/65 w
Rf gain: 20-30-34-40 db versions
Output level: 116-118-123 dbuv versions( en norms apply )
F-type connections.
GaAs-ET , Push pull
In house power supply
In 20pcs/pack.
Dimensions :
35*45*55 cm
Weight app :
32kgs/pack.
WSPS-2450-5000 Solid State Power Generator is specially designed for ISM application. It provides higher than 5kW RF Power, and it can work at CW(Continuous Wave) and pulse status. The features of this product are:Accurate output power adjustment from 10-5000W. Accurate output phase adjustment from 0-360 degree.Accurate duty cycle adjustment under pulse mode. PLL phase-locked technology ensure a high frequency stability Built in circulator and load enable the SSPG adapt to kinds loads that have different VSWR Reasonable protection circuit guarantee a reliable operation.
Long Pulse Single Frequency PM Fiber Amplifiers for DWDM transmission system
We will try our best to provide products similar to keopsys fiber amplifier like CEFA-C-WDM-LP fiber amplifier and CVFA fiber amplifier, NKT Photonics fiber amplifier like X15/E15/C15/Y10 signal-frequency lasers, NP Photonics fiber amplifier like the Rock Fiber Laser Module and the Rock Table- Top Fiber Laser Source, IPG Photonics fiber amplifier like GLR CW green fiber laser, VLM visible fiber laser and Yeetrbium CW fiber laser, and BKtel Photonics fiber amplifier.
You probably see us at following exhibitions: SPIE Photonics West in USA, Photonica in Russia, OPTO Taiwan, LASYS in Germany, OPIE in Japan and so on.
Parameter unit Specification
Min Typ. Max
Part No CKLIA-1550-M-SF-LP
Center wavelength nm 1540 1550 1565
Peak power W - - 500
Pulse energy uJ 100
Pulse width ns 200
Repetition rate kHz 20
Output average power W 2.0 - -
Beam quality M2 1.3 1.5
Output power stability1
ï¼?8hoursï¼? % - 1 2
Output isolation dB 35 - -
SMSR dB 20 35
Input signal average power uW 30 100
Power supply VDC 24
Operating temperature -35 - 65
Storage temperature -40 - 85
Output fiber type PLMA-GDF-25/300-M
Core NA 0.09
Output fiber length m >0.3
Output fiber connector FC/APC or collimator
3-port circulator On request
Dimension mm 300(L)X170(W)X25(H)
1. The output power stability is measured under 25ï¼?30 minutes after warm-up;
2. For more information about integrated 3-Port Optical Circulator, please contact
with us
