V-rebplus is a 10/100m, self-adaptive, high performance, self-learning, remote ethernet bridge. Its low cost make it suitable for cost-sensitive bridging application or as a lan extender or subsection. When it is used as a extender or subsection, it can forbid filtrating to let all of the amount of traffic are transmitted in wan. Its 10 base-t interface can run in full duplex ethernet with topology and improve data throughput by eliminating the padding bit in 64 bytes frame. Variable speed up to 10mbps on the wan line is supported transparently. The line rate may be adjusted in running without any influence to v-rebplus. V-reb plus does not perform any negotiation over the link, which is specially suitable for satellites and other wireless broadcast applications.
Features:
*10/100m high fast powered self-adapting self-educated long-range ethernet bridge.
* lan according with: ieee802.3/ieee802.3u/ethernet interface: utp(rj45)
* wan interface: v.24/rs232 & v.35 optional
* wan line speed rate reaches up to 10mbps.
* speed of filtrating and transmitting is up to 30000 frame/ second. Buffer is 16m.
* it can store up to10000 mac. And mac addresses have functions of automatically learning and updating.
* ethernet utp interface has function of vlan802.1q. There have two transmitting mode to choose: data and image.
* automatically learn mac addresses on the lan to which it is connected, and forward only those frames destined for another lan.
Input Voltage 12V / 24V DC optional
Output Voltage 115V / 230V AC optional
Portable power for AC products, AC outlets for connecting multiple loads
High surge capacity for products that require more power to start
High efficiency converts virtually all of the battery's power to AC
Mounting brackets for convenient installation
Heavy duty stud-connection mounting
RS232 communication port
WIFI/BMS Optional
Overload and over temperature shut down
Low voltage and over voltage alarm/cut off
Input reverse protection
Short circuit protection
PI15 series is a pure sine wave inverter, high frequency machine solution, the product is small size, the solution is reliable and stable, the main function is to invert the DC 12VDC battery or 24VDC battery to AC 230VAC or AC 115VAC output, mainly used for emergency use Electricity, car inverter,
outdoor electricity and other occasions.
Gve(e1, g.703 to v.35, v.24 converter)
Detailed selling lead description
Features:
1) v-gve is an asic-based converter using one e1/g.703 to convert to v.35
2) can convert successive n x 64k (n=1-32) data stream into pcm signal of e1, the data rate is up to 2048kbps
3) placed in e1 frame, data user just needs necessary timeslot
4) setting timeslot is continuous and according to rate of data port
5) the data ports have v.35 and v.24/rs232c which are optional
6) the ports support external clock and become linking end line
7) v-gve satisfies the requirements of g.703, g.704&g.706 of itu
8) v-gve has local and remote loop backs. Therefore user can use circuitry-test and malfunction diagnose conveniently
Detailed product description
Features:
1) rate of data transition: n x 64kbps (n=1-31), 2, 048kbps
2) transmission mode: synchronization
3) line interface: impedance 75 ohm, physical interface bnc; impedance 120 ohm, physical interface rj45
4) transmission features: comply with g.703
5) clock: line; external
6) testing method: local analogy loopback, remote digital loopback
7) dce interface: v.35 or v.24/rs232c
8) power supply: 220v f+ 10%, 50hz; 48v dc (optional)
9) power consumption: 5w
10) volume (l x w x h): 225 x 145 x 40mm; 9" x 5.8" x 1.6"
11) temperature: 0 - 40fpc
12) humidity: 0~95%
GVE-Tplus is E1 to V.35/V.24/RS232 and Ethernet Converter. Other series interface RS449/RS530/X.21 also can be optional. E1 port can support BNC/75ohm and RJ45/120ohm optional.
This device provides an economical digital access solution for E1 and fractional E1 network services. With a adapter cable, the device can connect to other DTE device, such as router, at data rates of 64Kbps to 2048Kbps.User data is placed into the E1 frame, using only the required number of timeslots, timeslot assignment is accomplished according to the data port speed and manual setting of DIP switches. The V.35 or V.24/RS232 and Ethernet share the 2Mbps bandwidth, the total bandwidth of the 2 interfaces must be not more than 1984Kbps.GVE-Tplus is widely used in communication network, both in WAN and LAN connection field.
Features:
*Comply with ITU V.35, G.703, G.704, G.706, G.823
*Full comply with IEEE 802.3 /IEEE 802.1Q (VLAN)
*Framed (N*64Kbps) and unframed (2.048Mbps) optional
*Ethernet port 10Mbps, Full/Half Duplex mode compatible
*Frame mode support PCM30/PCM31
*Support CRC4
*Support internal clock, E1 recovery clock or V.35 line clock
*Provide analog and digital loopback and remote digital loopback test
*For E1 interface, 75ohm (unbalanced) and 120ohm (balanced) optional
*For data interface, V.35 and V.24/RS232 optional
*Comprehensive LED indicators on front panel, convenient for the diagnosis of equipment working state
*Stand-Alone and Rack-Mount available
*16-slots, elaborate cooling design and two redundant power supplies
*Support management
*-48V DC & 220V AC power supply optional
Specifications:
E1 & FE1 interface
Comply with ITU G.703,G.704,G.706,G.823
Rate:2.048Mbps;N*64Kbps(N=1~31)
Code type:HDB3
Impedance:75ohm unbalanced & 120ohm balanced optional
Physical interface:BNC coaxical for unbalanced
RJ45 twisted pair for balanced
V.35,V.24/RS232 interface
Comply with V.35,V.24/RS232 standard
Rate:2048Kbps;N*64Kbps(N=1~31)
Transmission mode:Synchronization
Data interface:V.35 or V.24/RS232
Physical interface:DB25 female jack,V.35 via external adapter
Work mode:DCE
Power supply
AC power:220V¡¨¤10%,50Hz
DC power:-48V(optional)
Power:5W
GVE-Tplus(E1/G.703 to V.35 Ehernet converter
Detaile Selling Lead Description
Features:
1) GVE-T plus can convert E1 to both V.35 interface and LAN interface
2) Bandwidth of every port can be set into N x 64kbps (N=1-31) continuous data stream, although the total bandwidth of the two ports must be no more than 31 and must be inserted into PCM time slot of E1. It supports choices of CRC4 on/off and CAS/CCS (30 & 31 time slot)
3) GVE-T plus also can distribute the whole E1 capacity to V.35 data interface, although E1 must be framed N x 64kbps (N=1-31). The work mode can be either internal clock and slave-clock, or N x 64kbps (N=1-31) external clock to achieve end- linking line
4) GVE-T plus can be set up into long-range Ethernet Bridge from V.35 to LAN interface
5) GVE-T plus has two transmission modes to choose from: data and image
6) GVE-T plus has local and remote loop backs. Therefore user can use circuitry-test and malfunction diagnosis conveniently to perform port-to-port integrity test
Detailed Product Description
Ethernet features:
1) LAN table: 10,000 automatic learning and updating
2) Filtering and forwarding: 30,000 frames / second
3) Buffer size: 64M
4) Throughput delay: 1 frame
5) VLAN: comply with 802.1Q
LAN feature:
1) Standard: conforms to IEE802.3 / Ethernet
2) Work mode: full duplex / half duplex
3) Data rate: 10Mbps
4) Physical interface: 10 BaseT (UTP), shielded RJ-45
5) WAN E1 / G.703 feature:
6) Line transmission rate: N 64Kbps (N=1-31) 2048Kbps
7) Line coding options: HDB3
8) Format of line frame: G.703 (framed / unframed)
9) Line interface: BNC; RJ45
Transmission features:
1) Comply with G.703
2) Rate of data transmission: N 64Kbps (N=1-31)
3) Transmission mode: synchronization
4) Data interface: V.35 or V.24 / RS232C DCE
5) Clock: master clock; slave clock; external clock
6) Testing methods: local analogy loopback test; remote digital loopback test
Feature:
1) Power supply: 220VACf+10%, 50Hz 48V DC (optional)
2) Power consumption: 5W
3) Volume: 225 x 145 x 40mm; 9" (L) x 5.8" (W) x 1.6" (H)
4) Temperature: 0 - 40fpC
1699 Rs232 V 35 To Ethernet Converter Suppliers
Short on time? Let Rs232 V 35 To Ethernet Converter sellers contact you.
-10/100M self-adaptive Ethernet Interface
-Support ATUO MDI/MDIX, allowing crossover cable connection or straight-through cable connection
-Selectable Baud rate between 1299bps and 921.6Kbps -Build-in WEB server, allowing users to configure their webpage easily
-Auto reconnection after a network break, ensure the reliable TCP connection for the whole network
-Support DNS, can achieve a communication using the domain name
-Compatible to SOCKET working modes (TCP Server, TCP Client, UDP and etc.), the upper layer machine software is written strictly following the SOCKET rules
-TCP modes supports multi connections, specific data sending after password verifying, allowing up to 4 user to manage a single embedded device at a same time
-Advanced security mechanisms, prevent illegal access from unauthorized visitors, provide IP verifying firewall, and up to 8 configurable IP or IP segment certifications
-Support the local and remote upgrading of the firmware;Support AT Command configuration;Support remote configuration
-16 bits ARM7 CPU;
-Ethernet: 10/100Mbps
-Protections: build-in 2KV surge protection
-Type:RS232, RS485
-Control Signals :TXD,RXD,GND
-Parity: None, Even, Odd
-Data Bit: 5, 6, 7 or 8 bits
-Stop Bit: 1 or 1.5 bits
-Flow Control: Non
-Baud Rate: 1200bps~921.6Kbps
-Compatible Protocol: Ethernet, ARP, IP, UDP, TCP, BootP
-Network Services: DHCP, DNS, PPPoE, TFTP, HTTP, UDP Broadcasting -Client/Server: Server
-Ethernet Connector: RJ-45
-Ethernet Speed/Duplex: Auto-negotiation 10/100Mbps, Full/Half duplex -Auto-MDIX: Yes -WOL: Magic Packet, Wakeup Frame, Link-Up events
-Software Tool: VSP Driver, DS Manager, Web Server
-Configuration Mode: Web browser configuration tool, Windows Hyper Terminal, Telnet, Serial port configuration
-Power Input: 3.3V DC
-Physical Size (Wí-Dí-H): 77.5í-41.7í-22.7(mm)
Potabee, a potato chip snack made from real potatoes. Potabee is cut precisely with a technology known as V-cut, which makes it crunchier and tastes better. Potabee also contains spices which make it even more delicious. Available in 7 variants: - Roasted Seaweed - BBQ - Grilled chicken - Melted Cheese Steak - Selection Salted Egg - Wagyu Beef steak Selections - Selection Black Truffle size: - 15gr x 60 pcs - 35 gr x 40 pcs - 68 gr x 30 pcs - 120 gr x 18 pcs
Potabee, a potato chip snack made from real potatoes. Potabee is cut precisely with a technology known as V-cut, which makes it crunchier and tastes better. Potabee also contains spices which make it even more delicious.
Available in 7 variants:
- Roasted Seaweed
- BBQ
- Grilled chicken
- Melted Cheese Steak
- Selection Salted Egg
- Wagyu Beef steak Selections
- Selection Black Truffle
size:
- 15gr x 60 pcs
- 35 gr x 40 pcs
- 68 gr x 30 pcs
- 120 gr x 18 pcs
1. Compatible with rs232, rs485 tia/eia standard
2. Automatically send/receive data, without external traffic control signals
3. Communication rate: 300-38400bps
4. Communication distance: 1.2km(9600bps)
5. Can connect 32pcs rs232 or rs485 devices.
Stand alone Managed 10/100/1000Base-Tx to 10/100/1000Base-Fx Media Converter
SUN Telecoms stand alone Ethernet Media Converter is offers a cost-effective product to transmit distances up to 120km (Single-mode fiber). It makes it easy to incorporate the advantages of fiber-based connection technology in a managed Ethernet/Fast Ethernet network. Integrated Auto Cross-over MDI/MDI-X and NWay capabilities make it simple to deploy within a network. Also, the í¦hot-swappableí¦ design is ideal for scaling the system up or down quickly.
Features:
Web, SNMP, Console management
Hot-swappable module
Available with ST, SC, or WDM Simplex SC single-fiber connectors
Auto MDI/MDI-X on copper port
Auto-negotiation on copper port
LED status for Link/Activity, LFS, 100, Loopback, and Full Duplex/Collision
Link-Fault Signaling illuminates to indicate link failure
Link-Fault Signaling function can boot up redundant link if network is installed with primary and redundant link
Local and remote loopback
Features:
> > 8 channel 4~20ma signal acquisition, channel to channel is isolated
> > testing accuracy> 0.05%
> > rs485/232 output, can programme the accuracy of module
> > input/output/power supply three-port isolation: 3000vdc
> > wide power supply: 8~50vdc
> > high reliability, programming convenience, easy to install.
> > users can set module address, baud rate.
> > support modbus rtu communication protocal
Applications
> > temperature signal testing/monitoring/cintrol
> > rs232/485 industrial automation control system
> > industial field signal isolation
> > process monitoring & control
> > test sensors signal
> > laboratory data acquisition
> > medical machine monitoring
> > 4~20ma signal acquisition
With the support of skilled professionals, we are able to trade and supply quality approved Remote IO Module. Sourced from our trusted vendors of the market, this IO module is made using best grade component and pioneered technology at their well-equipped manufacturing unit. Furthermore, this IO module is immensely checked by our quality experts by passing it through various quality parameters. Our prestigious clients can avail this IO module at market leading prices.
Features:
Low power consumption
Easy installation
Long service life
GVE-Tplus is an upgrade of GVE-T. It is based on the ASIC circuitry design technology. It is a multi-functional, multi-purpose E1/G.703 to V.35 and LAN three-in-one multiplexer, which is also knowns as the three-in-one interface converter.
GVE-Tplus can not only be set up into GVE-T, but also can distribute the whole E1 capacity to V.35 data interface, although E1 must be framed N*64Kbps(N=1--31). The work mode can be either internal clock and slave-clock, or N*64Kbps(N=1--31) external clock to achieve end-linking line.
GVE-Tplus can be set up into long-range Ethernet bridge from V.35 to LAN interface. With low cost, it is suitable for use in bridge connection which is sensitive to cost or use in LAN as a stretcher or subsection. It can learn automatically MAC address in the connected LAN and only transmit the aim address to frame in another LAN. There are more than 10000 addresses in its LAN table. And they can be updated automatically. The highest speed of filtrating and transmission is 30000 frame/second(line speed). The buffer size is 64M. The throughput delay is 1 frame. When it is used as a stretcher or subsection, it can forbid filtration so that all traffic can be broadcasted in WAN. 10baseT interface can run in full duplex Ethernet with topology and improve data throughput by eliminating filled blanks in the 64 bytes frames. Without any negotiation in V.35 port, it is specially suitable for use in satellites and other wireless broadcast.
The RS232 to Ethernet Converters, used for data transparent transmission. USR-TCP232-302 is a low-cost serial device server,whose function is to realize bidirectional transparent transmission between RS232 and Ethernet. USR-TCP232-302 is internally integrated with TCP/IP protocol. User can apply it to device networking communication.
Features of RS232 to Ethernet Converters
Support DHCP, automatically obtain an IP address and query IP address through serial setting protocol
Support DNS function
Set parameters through webpage
Upgrade firmware via network
Auto-MDI/MDIX, RJ45 port with 10/100Mbps
Serial port baud rate from 600 bps to 230.4 Kbps, Check bit of None, Odd, Even, Mark and Space
Work mode: TCP Server, TCP Client, UDP Client, UDP Server, HTTPD Client
Support virtual serial port and provide corresponding software USR-VCOM
Heartbeat package mechanism to ensure connection is reliable, put an end to dead link
User-defined registration package mechanism, check connection status and use as custom packet header
Under TCP Server mode, Client number ranges from 1 to 16; default number is 4
The global unique MAC address bought from IEEE, user can define MAC address
Restore factory default
Across the gateway, switches, routers
Can work in LAN, also can work in the Internet (external network)
Provide PC TCP/IP socket programming example such as VB,C++,Delphi,Android and IOS
Support customization
Application Field of RS232 to Ethernet Converters
Industrial data transmission, industrial automation
security and protection monitoring, public security
Smart home, power control, environmental monitoring, intelligent agriculture
Door check on work attendance system, POS system, rice selling system
Building automation system, power monitoring, self-service banking system, telecom machine room monitoring
USR-N540, 4 serial port Ethernet converter which can realize transparent transmission between TCP/UDP data package and RS232/RS485/RS422 interface.
Industrial Solution TI Cortex M4 Solution, -40~85C
Web Server Web socket/ Web to Serial
Modbus Gateway Modbus RTU to Modbus TCP / Modbus Pollinig
Flow Control CTS/RTS, XON/XOFF
Protection Watchdog circuit, never cash
ESD 8KV
Anti-surge
Network Network Printing
2 network links, each serial support sending data to two servers
Feature of 4 ports Serial Ethernet Converter
TI Cortex-M4 kernel,industrial working temperature range and TCPIP protocol stack.
Auto-MDI/MDIX,RJ45 port with 10/100Mbps
TCP Server,TCP Client,UDP Client,UDP Server and HTTPD Client work mode
4 ports can work independently at the same time
Can distinguish which serial port connects to the device via port number
Support virtual serial port and provide corresponding software USR-VCOM
Serial baud rate from 600bps to 230.4K bps
DNS and DHCP supported
Provide PC TCP/IP socket programming example such as VB,C++,Delphi,Android and IOS
Built-in webpage;also can customize webpage for users
The global unique MAC address bought from IEEE (begin with D8-B0-4C);user can define MAC address
Support upgrade firmware via network
Support keepalive,rapidly detect dead links
Support account and password,can be used to page login and network settings
Support one channel Websocket,realize bidirectional transparent transmission between webpage and serial 0
Support Modbus RTU to Modbus TCP
Support UDP broadcast function
Each serial can work as rs232,rs485 or rs422; Default port is RS232 BD9 male port
Four channel serial communication indicator: TX/RX, CTS/RTS, XON/XOFF
Support DC adapter and 5.08-2 terminal power supply
Reload button,one key to restore default settings
RJ45 with Link/Data indicator light,built-in isolation transformer and 2 KV electromagnetic isolation
Application Field of 4 ports Serial Device Servers
Industrial data transmission, industrial automation
security and protection monitoring, public security
Smart home, power control, environmental monitoring, intelligent agriculture
Door check on work attendance system, POS system, rice selling system
Building automation system, power monitoring, self-service banking system, telecom machine room monitoring
Serial ethernet converter USR-N510, which can realize bidirectional transparent transmission between RS232/RS485/RS422 and Ethernet. Through simple settings via webpage or setup software can assign working details, realize serial data and TCP/IP data package transparent transmission by serial ethernet converter. USR-N510 is based on ARM processor and it is internally integrated with TCP/IP protocol. User can easily realize embedded device networking.
Application Field For [Serial Ethernet Converter]
Industrial data transmission, industrial automation
security and protection monitoring, public security
Smart home, power control, environmental monitoring, intelligent agriculture
Door check on work attendance system, POS system, rice selling system
Building automation system, power monitoring, self-service banking system, telecom machine room monitoring
Character
Industrial Solution TI Cortex M4 Solution, work temp at -40~85C
Power Supply DC/Terminal type 5V~36V
Serial Port RS232/RS485/RS422, 3-in-1 serial port
Serial Signal RS232: TX/RX, CTS/RTS
RS485:A/B/G
Flow Control Software: XON/XOFF
Modbus Gateway Modbus TCP to Modbus RTU in bi-directional
Modbus Polling
Advanced Character -Network Printing
-Web socket: Serial to Webpage
-Modify MAC
-Hardware watchdog
-ARP of server domain name
Certification CE/FCC/RoHs/WEEE
Work Mode TCP Server/ TCP client/ UDP Server/UDP Client/ HTTPD Client
Built-in web page Customized web page is acceptable
Protect Surge Protection, ESD 2KV, for more harsh industrial environment
Point 1
Ethernet 10/100Mbps, support Auto-MDI/MDIX
A port can correspond to 2 Sockets
Provide PC TCP/IP socket programming examples such as VB, Andriod, IOS etc.
Point 2
Virtual serial port, provide corresponding software USR-VCOM
Baud rate: 600bpgs~230.4Kbps
Reload button to restore default settings
Support keep alive, rapidly detect dead links.
Diversified interfaces including SFP+ TO SFP+, SFP+ TO XFP, XFP TO XFP,
Supports 3r (re-generation, re-timing, re-shaping)
Fiber mode converter between fiber to fiber 10gbps equipment, or fiber repeater for long distance transmission
1310nm /1550nm/cwdm/dwdm optical wavelength conversion.
Oeo for network backbone(san, lan, man)
Support 2u rack (16 channel) and standalone use
Support jumbo frame
Transmission rate:9.95gbps-11.35gbps
Support hot plugging .
10gbps fiber to copper media converter for long distance transmission
Network management function web snmp console
Support dmi function for sfp+ fiber module
Support itut prescribed dwdm/cwdm wavelength
Media converter for network backbone(san, lan, man)
Support 2u rack (16 channel) and standalone use
Support jumbo frame
Sfp+ fiber module detection, utp cable length detection
Support hot plugging
Type: rj45 to/from sfp+.
Parameter
Specifications
Access mode
10/100mbps
Standard
Ieee802.3 10base-t ethernet, ieee802.3u, 100base-tx/fx fast ethernet, ieee802.3x flow control, ieee802.1q vlan, ieee802.1p qos, ieee802.1d spanning tree
Wavelength
850nm/1310nm/1550nm
Transmission distance
Single-fiber single-mode: 25/40/60/80/100km ; category-5 twisted pair: 100m
Port
One rj45 connector, connected to stp/utp category-5 twisted pair one fiber port: multi-mode - sc or st (fiber size: 50, 62.5/125µm) single mode - sc/fc fiber port (fiber size: 9/125µm) single-fiber single-mode - sc/fc fiber port (fiber size: 9/125µm)
Conversion mode
Medium conversion, storing and forwarding
Mac address table
I k
Buffer space
1mbit
Flow control
Full duplex state: flow control; half duplex state: back pressure mode
Delay
9.6us
Bit error rate
<1/1000000000
Mtbf
100, 000 hours
Led
Power tx link ( fiber link action ), tp link1000, tp link100, tp act ) fdx (fx full duplex mode), fx100 (fiber, with a transmission rate of 100m) tp1/2/3/4 link/act (1/2/3/4-port twisted pairs connection action) tp1/2/3/4100 (1/2/3/4-port twisted pairs, with a transmission rate of 100m)
Power
Ac220 0.5a/pc-48(builtin)
Power consumption
5w
Operating temperature
-10~55ºc
Operating humidity
5%~90%
Storage temperature
-40~70ºc
Storage humidity
5%~90% (non-condensing)
Dimensions
140mm * 111 * 30mm(in) 95 x 70 x 26mm(out)
1699 Rs232 V 35 To Ethernet Converter Suppliers
Short on time? Let Rs232 V 35 To Ethernet Converter sellers contact you.
