Introduction to Lubricant oil additive PIBSA Mn=1000
PIBSA-1000 is polyisobutylene succinic anhydride that prepared by high-activity polyisobutylene (Mn=1000) and maleic anhydride, can be used for the preparation of fine performance ashless
dispersant, can also be used to produce other additives.
Technical Index of Lubricant oil additive PIBSA Mn=1000
Item Typical Value
Appearance Viscous Transparent Liquid
Kinematic Viscosity(100),mm2/s 500-650
Saponification Value,mgKOH/g 90
Free Acid Value,m% 1
Ethylene glycol (IUPAC name: ethane-1,2-diol) is an organic compound with the formula (CH2OH)2. It is mainly used for two purposes, as a raw material in the manufacture of polyester fibers and for antifreeze formulations. It is an odorless, colorless, sweet-tasting, viscous liquid.
Ethylene glycol is a high-production-volume chemical; it breaks down in air in about 10 days and in water or soil in a few weeks.It enters the environment through the dispersal of ethylene glycol-containing products, especially at airports, where it is used in de-icing agents for runways and airplanes. While prolonged low doses of ethylene glycol show no toxicity, at near lethal doses(â?¥1000 mg/kg per day) ethylene glycol acts as a teratogen. "Based on a rather extensive database, it induces skeletal variations and malformations in rats and mice by all routes of exposure." This molecule has been observed in outer space.
Commodity
Ethylene Glycol
Production batch number
3703W7120620
Inspection date
20201218
Items
Unit
Result
Standard
1.Polyethylene glycol series products can be used in pharmaceuticals. Polyethylene glycol with low relative molecular weight can be used as solvent, co-solvent, O/W emulsifier and stabilizer, used to make cement suspensions, emulsions, injections, etc., and also used as water-soluble ointment matrix and suppository matrix, solid waxy polyethylene glycol with high relative molecular weight is often used to increase the viscosity and solidification of low molecular weight liquid PEG, as well as compensate other drugs; For drugs that are not easily soluble in water, this product can be used as a carrier of solid dispersant to achieve the purpose of solid dispersion, PEG4000, PEG6000 is a good coating material, hydrophilic polishing materials, film and capsule materials, plasticizers, lubricants and drop pill matrix, for the preparation of tablets, pills, capsules, microencapsulations, etc.
2.PEG4000 and PEG6000 are used as excipients in the pharmaceutical industry for the preparation of suppositories and ointments; It is used as a finishing agent in the paper industry to increase the gloss and smoothness of paper; In the rubber industry, as an additive, it increases the lubricity and plasticity of rubber products, reduces power consumption during processing, and prolongs the service life of rubber products.
3.Polyethylene glycol series products can be used as raw materials for ester surfactants.
4.PEG-200 can be used as a medium for organic synthesis and a heat carrier with high requirements, and is used as a moisturizer, inorganic salt solubilizer, and viscosity adjuster in the daily chemical industry; Used as softener and antistatic agent in the textile industry; It is used as a wetting agent in the paper and pesticide industry.
5.PEG-400, PEG-600, PEG-800 are used as substrates for medicine and cosmetics, lubricants and wetting agents for rubber industry and textile industry. PEG-600 is added to the electrolyte in the metal industry to enhance the grinding effect and enhance the luster of the metal surface.
6.PEG-1000, PEG-1500 is used as a matrix or lubricant and softener in the pharmaceutical, textile and cosmetic industries; Used as a dispersant in the coating industry; Improve the water dispersibility and flexibility of the resin, the dosage is 20~30%; The ink can improve the solubility of the dye and reduce its volatility, which is especially suitable in wax paper and ink pad ink, and can also be used in ballpoint pen ink to adjust ink viscosity; In the rubber industry as a dispersant, promote vulcanization, used as a dispersant for carbon black filler.
7.PEG-2000, PEG-3000 are used as metal processing casting agents, metal wire drawing, stamping or forming lubricants and cutting fluids, grinding cooling lubricants and polishes, welding agents, etc.; It is used as a lubricant in the paper industry, etc., and is also used as a hot melt adhesive to increase rapid rewetting capacity.
INTRODUCTION
The product is a high molecular 30 TBN Calcium Sulphonate. The increased oil solubility of the organic portion of this Sulphonate enables the product to provide rust protection and acts as a dispersant for graphite and molybdenum disulfide. It can be used as an additive in lubricating oils, greases, rust inhibition, antiwear and hydraulic fluids.
SPECIFICATION
Test Method Minimum Maximum
Appearance Visual Brown liquid Brown liquid
Colour ASTM D 1500 2 5
Sp. Gravity @ 15.6 C ASTM D 1298 0.95 1.05
Flash Point C (COC) ASTM D 92 175 -
Viscosity @ 100 C, cst ASTM D 445 40 70
Avg. Molecular wt. ASTM D 3712 1000 1100
TBN (mg KOH/gm) ASTM D 974 28 35
Calcium Content %[w/w] GL EDTA 1A 2.8 3.0
FORMULATION
The product is recommended for use at 0.5% to10.0%wt. In suitable base stocks to provide
detergency & anti-rust performance characteristics to oils. It is compatible with mineral base oils, white oils, and synthetic base stocks.
APPLICATION
Imparts excellent rust prevention, detergency and Anti oxidant Properties.
Corrosion inhibitor in mill oils, short-term rust preventatives, coatings and greases.
Dispersant and corrosion inhibitor in engine oil.
Provides excellent resistance to coated Cold Rolled Steel for antirust applications.
Works in extremely hostile conditions like highly acidic environment as well as highly humid atmosphere.
It is non-staining having detergent, dispersant properties.
Environmental Friendly, Biodegradable without side effect.
HANDLING AND STORAGE
Calcium Sulphonate is normally handled at room temperature. For general purposes, the following storage and handling temperatures are recommended: Storage Handling 50-70C
(122-158F).
For more extensive information on the safe handling and use of this product, see the Material
Safety Data
An additive intermediate prepared from highly active polyisobutylene (molecular weight=1000).
The products can be used for producing various types of polyisobutylene succinimide and boronized dispersants. It can also be used for the production of emulsifiers and processing aids for petrochemical plants. The recommended addition is 2 % - 10 %.
85 Pibsa 1000 Polyofene Butadiacin As Dispersant Suppliers
Short on time? Let Pibsa 1000 Polyofene Butadiacin As Dispersant sellers contact you.
Linear Alkybenzene Sulfonic Acid (sometimes referred to as Dodecylbenzene Sulfonic Acid or DDBSA) is a light yellow to dark brown colored liquid. LABSA is widely used in household products like detergents, shampoos, and hair conditioners, as well as in numerous industrial applications like as a catalyst for the esterification of fatty acids to produce biodiesel, and also for the synthesis of quinoxaline derivatives. LABSA is also used as a dopant for conducting polymers, a wetting agent, a dispersant, a foamer, a paraffin inhibitor, acidizing agent and an emulsion breaker.
Linear Alkylbenzene Sulfonic Acid (LABSA)
WC Code: 04-073-003
Sales Specification
Appearance: Viscous Amber Liquid
Active Matter (Mws: 322): 96.0 % MIN
Unsulfated Organic matter: 2.0 %MAX
Free Sulfuric Acid: 1.50 % MAX
Color, Klett (5% AM soln): 40 MAX
Acide Value: 182.0 to 188.0
Packing
PIBSA1000 is a lubricant additive intermediate prepared from high reactive polyisobutylene (Mn=1000) by thermal adduction process. The ashless dispersant produced from PIBSA1000 possesses fine detergency and favourable low temperature sludge dispersion.
2.SPECIAL FEATURES
Free of chlorine
3.APPLICATIONS
Used for preparation of polyisobutylene diene and polyene succinimide and bononize ashless dispersant.
Used for preparation of emulsifying agents for emulsion explosives.
Used for preparation of processing aids for petroleum chemical plant
4.CHARACTERISTICS
ITEM TYPICAL VALUE TEST METHOD
Appearance Reddish brown viscous liquid Visual
Flash point (COC), â?? â?¥180 GB/T3536
Kinematic viscosity (100â??),mm2/s â?¥800 GB/T265
TAN, mg KOH/g â?§90 Q/YHT012
The enterprise standard Q/JTH012-2008
5.STORAGE
The packing,marking,transportation,storage and delivery acceptance should meet the requirement of SH/T1064.Store in dry,clean and ventilating warehouses.
6.PACKING
The product is packed in 200 liter metal drum(net weight:170kg/drum).
Specifications
Products Calcined Kaolin
Use Industrial Use
Color White to Super White
Form Powder
Packing Type Plastic Bags
Packaging size 25kgs
Whiteness: 90-94%
Calcined Kaolin is an anhydrous aluminium silicate produced by heating hydrous china clay after water washing to high temperatures in a rotary kiln. The clacination process gives an increase in the original hardness of kaolin and alters the morphology of the kaolin particles completely. When calcination process is done at around 700 deg C, the dehydrogenate of the kaolin is complete, forming a partially crystalline meta kaolin. Fully calcined kaolin products with an amorphous structure are formed around 1000 deg C.
Fully Calcined kaolins can be surface modified with functionalised coupling agent Silane to give a particle coating capable of chemically bonding with the polymer. After surface treatment the dispersion of filler is also improved. In view of the reduced surface activity, calcined kaolins give good reinforcement and permanent set properties, at the same time maintaining very good processing conditions.
The processing techniques at PEEKAY MINERALS ensures consistent quality, low specific gravity, good whiteness and freedom from impurities at pocket friendly costs.
Application:
Rubber & PVC Cable insulation
Paints & Pigments
Paper & Boards
Printing Inks
Ultramarine Blue
Pharmaceutical seals & Gaskets
Rubber Hoses
Rubber Footwear
Speciality plastic films
Engineering thermoplastics
Thermosetting plastics
Features:
Free from impurities
Unique particle size
Lower finish costs
Improving brightness and opacity
Low Bulk Density
Very good process ability
This car shampoo is a biodegradable new high foam formula that remove tough dirts, road grimes and contaminants. Perfect for all type of paints including clear coats. It gently rinses, leaving a brilliant shine, repels water while leaving a dry surface with an excellent shine to your car without the use of any additional waxes or polish. It is very suitable to be use on all type of vehicles including commercial buses, vans, lorries etc as it has a rich advanced formula that will easily wash off the toughest dirts while uplifting the paint of your car with an excellent shine.
Product attributes:
-gently foam away dirts
-excellent suds
-sodium chloride free formula
-leaves a brilliant shine
-2 in 1 formula wash & shine
-biodegradable formula
-repels water
Rinse the surface of your vehicle with water, dilute 30 - 60 ml (1 to 2 caps) in a bucket and add 2.5l of water. Mix the water so as to disperse the car shampoo liquid. Apply with on cold surfaces of your car with a sponge and clean by rubbing. Rinse with clear water to remove any suds and foam after every wash.
Attention:
Keep out of reach of children. Avoid contact with the eyes.
compressed air filter
1). Separator filter (HF9)
For bulk liquid removal plus a 3 micron coalescer (5ppm w/w maximum remaining oil content)
Two-stage filtration
* First stage: two stainless steel orifice tubes provide 10 micron mechanical separation
* Second stage: in-depth fiber media captures solid and liquid particles to 3 micron
2). Air line filter (HF7)
For removal of liquid water and oil; removes solid particles to 1 micron (1.0 ppm w/w maximum remaining oil content)
Corrosion resistant inner and outer cores
Two-stage filtration
* Firt stage: captures larger particles with alternate layers of fiber media and media screen
* Second stage: coalesces aerosols and captures solid particles with multiple layers of epoxy bonded, blended fiber media
3). High efficiency oil removal filter (HF5)
For coalescing fine water and oil aerosols; removes solid particles to 0.01 micron (0.01 ppm w/w maximum remaining oil content)
Corrosion resistant inner and outer cores
Two stage filtration
* First stage: multiple layers of bonded, blended fiber media for fine coalescence
* Second stage: multiple layers of bonded, blended fiber media for fine coalescence
Outer coated, closed cell foam sleeve
4). Ultra high efficiency oil removal filter (HF3)
For coalescing ultra-fine oil aerosols; removes solid particles to 0.01 micron (0.001 ppm w/w maximum remaining oil content)
Corrosion resistant inner and outer cores
Two stage filtration
* First stage: coated, closed cell foam sleeve acts as pre-filter and flow disperser
* Second stage: multiple layers of matrix blended fiber media for ultra-fine coalescence
Outer coated, closed cell foam sleeve
5). Oil vapor removal filter (HF1)
For removal of oil and hydrocarbon vapors normally absorbable by activated carbon; removes solid particles to 0.01 micron (0.003 ppm w/w maximum remaining oil content)
Corrosion resistant inner and outer cores
Two stage filtration
* first stage: stabilized bed of finely divided carbon particles removes the majority of the oil vapor
* Second stage: multiple layers of fiber media with bonded micro fine carbon particles remove the remaining oil vapor
Multiple layers of fine media prevent particle migration
Outer coated, closed cell foam sleeve prevents fiber migration
Designed life is 1000 hours under rated conditions.
1.High-shear dispersing impellers, good dispersion effect and safety, good dispersion effect by shearing strength around the gear plate, enabling products to be wet and dispersed efectively.
2. The products are accelerated in radial directioin via dispersion plate, flow to the top and bottom part on the inner wall of the cylinder and return to dispersion plate, enabling materials to be well stirred.
3. Uses latest frequency inverter, giving various speed control.
4. Manual control for rotation through 300 degrees, so that material barrel of different directions and positions can be mixed simultaneously(Optional).
5. Bracket structure, giving more safety while mixing(Optional)
Nanolin dk series of nanoclay introduced by fcc inc are made from high purified smectite that exhibit ultra-fine phase dimensions. The size of nanolin dk series of nanoclay are typically in the range of 1-100 nm while been fully dispersed, the average fully dispersed thickness of platellite is around 25 nm; the aspect ratio is 100-1000.
Calcite Powder is a naturally occurring form of Calcium Carbonate (CaCO3) with an extremely high degree of whiteness, purity. Calcite Powder is extensively utilized as a filler in the manufacturing of plastics owing to its low oil absorption, high dispersibility, smooth surface finish, high impact resistance, easy processing, unmatched dimensional stability, and its compatibility with other complex polymers and organic additives.
Price : INR 11,500 - 15,000 per Metric Tonne (1000 kg)
Packaging : 20kg, 25kg, 30kg, 38kg and 40kg
Product Type:White / Off White
Minimum Order Quantity : 5 Metric Tonne (5000 kg)
Transport : Cargo (by ship), Road, Train
Our horizontal mixers are suitable for mixing of various resins (pvc, pe, pp, and modified ptfe) with additives, auxiliary chemicals and fillers, dispersion, coloring, drying and homogenizing as well as for the removal of volatile components and drying of engineering plastics such as avs and pc before processing. Rational allocation for clients as per requirement, or individual purchase)
Model no.: srlw200/500, srlw300/1000, srlw500/1600, srlw800/2000, srlw800/2500, and so on.
Special features:
1) uniform and fast mixing
2) precision temperature control
3) high automatic degree
4) easy operation
5) packing: refer to international standard of export packing
T154A Polyisobutylene Succinimide
Specification : 200L/drum
Packing and handling : Metal drum
Transportation : Transport by road, sea or rail
Description : T154A is an ashless dispersant prepared from high reactive isobutylene by thermal adduction proce...
Description
T154A is an ashless dispersant prepared from high reactive isobutylene (=1000) by thermal adduction process. With better detergency capability, it can inhibit the carbon deposit and the formation of varnish. It doesn't contain chlorine.
Special features
Good detergency & dispersion effects
Free of chlorine
Applications
Used for blending medium and high grade diesel engine oils
Used for blending medium and high grade gasoline engine oils
Used for blending marine cylinder oils for low-speed crosshead engine
Particularly suitable for blending environment-friendly engine oils
The dosage: 2.0-4.0%
Characteristics
Item
Specification
Test method
Density, kg/m3, at 20oC
890.0 ~ 935.0
ASTM D1298
Flash point (COC), oC
¡Y 180
ASTM D92
Kinematic viscosity, mm2/s, at 100oC
130.0 ~ 180.0
ASTM D445
Nitrogen, mass%
1.20 ~ 1.40
ASTM D3228
Base number, mgKOH/g
15.0 ~ 30.0
ASTM D2896
The enterprise standard Q/JTH 007-2009
Points for Attention
It is packed in 200 litre metal drums. Store in dry, clean and well ventilated warehouses.
For the details of health and safety precautions, please see the related Material Safety Data Sheet.
Key Feature
1>.2-way full rang Line Array system
2>.500w, with single 2inch HF compression driver horn loaded;2 x 10inch LF cone driver
3>.Supported with a full range of flying accessories
4>.For portable use or permanent inatallation
5>.Pro circuit provides HF driver protection
6>.Distant directivity 72H x 10 V dispersion
7>.Bi-Amplifier or singal-Amplifier .
Application
1>. Medium and small arenas
2>. Ballrooms and clubs
3>. Stadium and pavilions
4>. Theatre live music
5>. Auditoriums and corporate centre .
Specification
* Frequency Response (+3 dB): 55 Hz - 20 kHz
* Sensitivity (1w/1m): 104 dB SPL
* Long-term SPL: 126 dB
* Maximum SPL: 132 dB
* Nominal Impedance: 4 ohms
* Power rated: 500 watts
* Peak Power handling: 1000 watts
* Nominal Dispersion: 72H x 10V
* Crossover Frequency: 1.8 KHz
* Dimensions (H x W x D): 320 mm x 820 mm x 550 mm
* Enclosure Material: 18mm birch polywood
* Surface Finished: black catalyzed polyurethane paint
* Grille: 1.5mm black perforated steel framed
* Net weight: 38 kg
* Low Frequency Driver: 2X10"cone driver
* High Frequency Driver: single 2"compression driver horn-loaded
* Input Connectors: Neutrik NL4MPX4.
Wl-156 is an anionic hydroxylated styrene acrylic copolymer emulsion. It is recommended to use with amino resins for baking coatings, which requires high gloss, good hardness and outstanding solvent resistance. Biocide: CMIT/MIT 3:1 49ppm, and MIT 240ppm.
Properties
1. Excellent resistance to boiling water
2. High gloss, high hardness
3. Excellent solvent resistance
4. Excellent recoatabilit
Note:Be sure to adjust the pH of WL-156 over 7 with the pH adjustment in use.
Characteristic data* Property Value Unit Method
Appearance Translucent to milky white
Weight Solids 47�±1 %
pH 3.5-5.5 GB 6920-1986
Viscosity 10-1000 mPs Brookfield,LV,62#,30rpm,25C
MFFT 40-42 C GB/T 9267-2008
OH content 1.3 % Calculated on solid resin
Density 1.04 g/cm3 GB/T 4472-2011
Rutile Type Titanium Dioxide TiO2 MBR9666 is an inorganic(SiO2,Al2O3) and special organic chemicals surface treated rutile grade titanium dioxide. It combines with high whiteness,high gloss,excellent tinting strength and weather durability, low oil absorption and ease of dispersion in both water and solvent based system.The quality is at the high level of china market and the price is very competitive which welcomed by both domestic and overseas customer.
Specs:
TiO2 Contents % 94 min
Rutile content % 98 min
Whiteness(Compare with standard sample) 96.5% min
Medium particle size: um 0.27
Tinting-strength (Reynolds number) 1880 min
Oil Absorption g/100g 20 max
PH 6.5-7.5
Residue 45um % 0.01 max
105°Volitile % 0.5 max
Water Soluble % 0.5 max
Applications: It is widely used into paints, coating, print ink, paper industry, plastic, synthetic fiber, textile, printing and dyeing,PVC pipe, Master batch etc and it is designed as an multifunction application used white pigment.
Treatment: Al2O3,SiO2 and organic treatment
Classifications: ISO591-1 2000(E): R2
ASTM D 476-00 V
CAS NO: 13463-67-7
Package: Packed by paper bag with net weight 25 Kg, 500 Kg and 1000 Kg or as per customer’s choice.
CALCINED SUPER WHITE AND FINE KAOLIN
Material: Calcined super white and fine kaolin
Grade: CK/92/96
Description: CK series kaolin are produced from highly refined kaolin through grind, calcination and classification. it has high purity and the quality is stabled.
It offers superfine particle and with excellent anti-settling property; It can easily disperse in water based systems;It is inert to most acids and alkaline at ambient temperature and offers good anticorrosive capabilities.
CAS NO.: 1332-58-7
H.S. CODE: 2507001000
Specs:
ITEM
CK92
CK-96
Brightness(T457)
92%min
=93.5%
SiO2
52+/-2
52+/-2
Al2O3
45+/-2
45+/-2
Particle Size (0-2micron)%
60+/-5
80+/-2
Particle Size (0-10micron)%
97%
100%
Refractivity
1.62
1.62
Screen residue (325 mesh %)
0.003max
=0.005
Oil Absorbency (g/100g)
50+/-5
60+/-5
pH
5.5-7.0
5.5-7.0
Moisture (%)
0.5max
=0.5
Applications: As MBCK series calcined kaolin pigment can be applied in latex paint, powder coating and electrophoresis coating, filing, paper making industry, ceramic, rubber, and plastic.
Package: Packed by paper bag with net weight 25 Kg, 500 Kg and 1000 Kg or as per customer's choice.
85 Pibsa 1000 Polyofene Butadiacin As Dispersant Suppliers
Short on time? Let Pibsa 1000 Polyofene Butadiacin As Dispersant sellers contact you.
