Features:
1. Compact size with high reliability.
2. Output signal strength indicators available.
3. Support antenna isolation detection.
4. Automatic gain control.
5. Intelligent mode setting, automatically set the values.
6. Auto shut off function available to avoid the damage and interference in unusual signal conditions.
7. Built-in service antenna, whole kit available.
8. Easy installation & maintenance.
Power supply Ac:110~240v; dc: 6v/2a
Operating temperature -10¡æ~50¡æ
Environment conditions ip30
Dimensions (d x w x h ) 103.5*83.5*49.4mm
Weight ¡ü800g
Specification te-8050 te-8060 te-8070
Frequency range uplink 824-849 mhz
Downlink 869-894 mhz
Gain ( db) uplink gp45 db gp55 db gp65 db
Downlink gp50 db gp60 db gp70 db
Export power (po) 15dbm 15 dbm 15 dbm
Pass band ripple 5db 5db 5db
Guard band rejection "¿bw-60db42mhz ,
¿bw-70db45mhz "
I/o impedance 50+/n connector
I/o return loss -20db
Noise figure 7db
Intermodulation attenuation (po=13dbm) -34dbc -34dbc -33dbc
Transmission delay 0.58s
Ambient temperature -10µ½50µ
Power supply ac110½220va10% 45½55hz
Size 97ß84ß28mm 97ß84ß28mm 97ß84ß28mm
Reliability to the gb6993-86 standard
Electromagnetic compatibility to the ets300 694-4 standard
Function "a) power supply led denote
B) export power led denote"
The device featured by easy installation & operation and no interference. It is the ideal device for boost mobile phone signal. A mobile phone repeater could also improve indoor magnetism environments, protract cellular battery life and reduce radiation of cellphones.
Features
l High gain, easy installation and operation.
l Full-duplex, single-port design, build-in power supply.
l Use ALC technology, adjust extent automatically
l LED Light Working & Signal Condition Indicators
l Big linear power, control intermodulation & saturation stably
l Dependability stand by GB6993-86 standard
l Compatibility of electromagnetism according with ETS300 609-4
a) Power supply LED denote
b) Export power LED denote
coverage area
3000 m2
Installation Approaches
Fix up outdoor antenna reception on housetop and point to signal tower.
Connect outdoor antenna to â??outdoorâ?� port in repeater machine through cable.
Connect indoor antenna(s) to â??indoorâ?� port in repeater machine through cable also.
Plug power adaptor into AC power socket and finish installation.
Technique Supporting
If still no signal receipt after activated repeater, please check if outdoor antenna point to signal tower or elsewhere have strong signal and check if strength achieve -70DBM.
If cannot call out, please adjust the direction of outdoor antenna.
If strength is not steady, please check if outdoor & indoor antennas are too close. Please ensure the outdoor and indoor antennas have distance of 20
Accessories
Selection Outdoor antenna use 7 unit yagi type antenna, indoor antenna use board or rooftop antenna and signal wire use coaxial-cable.
Packing list
Main unit 1pc
Power supply 1pc
User manual 1pc
Frequency range:up link:890f+915mhz downlink: 935f+960mhz
Export power:up link:10 dbm downlink: 10 dbm
Gain:up link:50 db downlink: :50 db
Function:a) power supply led denote b) export power eld denote
I/o impedence:50¬+/n connector
Noise figure:6db
Transmission delay:0.5»s
Ambient temperature:-15f¦f+55f¦
Power supply:ac/220vf+10% 45f+55hz dc·ª12v
Size:134mmf-95mmf-28mm
Electromagnetic compatibility:to the ets300 694-4 standard
Reliabilityto the gb6993-86 standard
Pass band ripple:1.8db
Coverage area:200sqm
í±High system gains.
í±Full duplex and double-end design,external power supply,and convenient installation.
í±ALC technology with auto-steady function adopted.
í±Provide power indication and uplink and downlink indications.
í±With the amplified linear power,the intermodulation and spuriousness are suppressed effectively.
í±The reliability conforms to GB6993-86 standards.
í±The electromagnetic compatibility conforms to ETS300 609-4 standards.
Specification
Dual Band (GSM+DCS) Signal Booster
Specification TE9018A TE-9018B TE-9018C
Frequency range Uplink GSM 890-915 +DCS1710-1785(MHz)
Downlink GSM 935-960 + DCS1805-1880(MHz)
Gain
(dB) GSM Uplink Gpí¦55 Gpí¦65 Gpí¦45
GSM Downlink Gpí¦60 Gpí¦70 Gpí¦50
DCS Uplink Gpí¦50 Gpí¦55 Gpí¦45
DCS Downlink Gpí¦55 Gpí¦60 Gpí¦50
Gain adjustable range MGCí¦30dB
Output power(dBmú¬ í¦17 í¦20 í¦17
Pass band ripple GSM í_4dB
DCS í_15dB
Guard band rejection GSM (BW-60dB)í_42 MHz (BW-70dB)í_45 MHz
DCS (BW-60dB)í_104MHz (BW-70dB)í_107 MHz
I/O impedance 50ª+/N Connector
I/O return loss í_-10dB
Noise figure í_-8dB
Intermodulation attenuation
(Po=13dBm)
í_-40dBc
Transmission Delay í_0.5ª¦s
Ambient temperature -10íµí½50íµ
Power supply AC110í½220Ví+10% 45í½55Hz
Size 148mmí-106mmí-33mm
Reliability To the GB6993-86 standard
Electromagnetic compatibility To the ETS300 694-4 standard
Function a) Power supply LED denote
b) Export power LED denote
835 15Dbm Mobile Signal Repeater Booster Suppliers
Short on time? Let 15Dbm Mobile Signal Repeater Booster sellers contact you.
í±High system gains.
í±Full duplex and double-end design,external power supply,and convenient installation.
í±ALC technology with auto-steady function adopted.
í±Provide power indication and uplink and downlink indications.
í±With the amplified linear power,the intermodulation and spuriousness are suppressed effectively.
í±The reliability conforms to GB6993-86 standards.
í±The electromagnetic compatibility conforms to ETS300 609-4 standards.
Specification
PCS Band Selective Signal Booster
Specification TE-9102A-XP TE-9102C-XP
Frequency range Uplink :1850-1910 MHz
Downlink:1930-1990MHz
Gain ( dB) Uplink Gpí¦55 Gpí¦45
Downlink Gpí¦60 Gpí¦50
Gain adjustable range MGCí¦30dB
Export power (dBm) í¦17 í¦17
Pass band ripple í_-15dB
Guard band rejection í+200k>5dB í+400k>10dB
í+600k>20dB í+1M>46dB
í+5M>50dB í+10M>52dB
I/O impedance 50ª+/N Connector
I/O return loss í_-8dB
Noise figure í_8dB
Intermodulation
Attenuation(Po=13dBm) (9KHzí½1GHz)í_-30dBm
(1í½12.75GHz)í_-30dBm
Transmission Delay í_0.5ª¦s
Ambient temperature -10íµí½50íµ
Power supply AC110í½220Ví+10% 45í½55Hz
Size 228mmí-106mmí-33mm
Reliability To the GB6993-86 standard
Electromagnetic
compatibility To the ETS300 694-4 standard
Function a) Power supply LED denote
b) Export power LED denote
Say The í¦Xí¦ in type means bandwidth be selected
í±High system gains.
í±Full duplex and double-end design,external power supply, and convenient installation.
í±ALC technology with auto-steady function adopted.
í±Provide power indication and uplink and downlink indications.
í±With the amplified linear power,the intermodulation and
spuriousness are suppressed effectively.
í±The reliability conforms to GB6993-86 standards.
í±The electromagnetic compatibility conforms to ETS300 609-4 standards.
Specification
GSM Full Band Signal Booster
Specification TE-9102A TE-9102B TE-9102C
Frequency range Uplink 890ú¡915MHz
Downlink 935ú¡960MHz
Gain ( dB) Uplink Gpí¦55dB Gpí¦65dB Gpí¦45dB
Downlink Gpí¦60dB Gpí¦70dB Gpí¦50dB
Gain adjustable range MGCí¦30dB
Export power (Po) í¦23dBm í¦23 dBm í¦20 dBm
Pass band ripple í_5dB
Guard band rejection ú¿BW-60dBú¬í_42MHz ,ú¿BW-70dBú¬í_45MHz
I/O impedance 50ª+/N connector
I/O return loss í_-8dB
Noise figure í_8dB
Intermodulation
Attenuation(Po=13dBm) í_-40dBc
Transmission Delay í_0.5ª¦s
Ambient temperature -10íµí½50íµ
Power supply AC110í½220Ví+10% 45í½55Hz
Size 148mmí-106mmí-33mm
Reliability To the GB6993-86 standard
Electromagnetic
Compatibility To the ETS300 694-4 standard
Function a) Power supply LED denote
b) Export power LED denote
Product description
Gsm signal repeater including broad band repeater, band selective repeater; frequency selective repeater; fiber opital repeater; frequency shifting repeater.
Today we draw your attention to our gsm frequency shifting repeater.
*system
1)frequency range:
Uplink 890~915mhz(6m, 19m, 25m are available)
Downlink 935~960mhz(6m, 19m, 25m are available)
2)transmission delay: <10us
Technical features:
1)receiving and sending separation, low require for ant isolation, making it convenient for installation.
2)mini design with metal cavity filters technology inside.
3)full-duplex & dual-port design, and built-in power supply, making it convenient for installation.
4)allowing for continuous gain adjustment 31db by 1db step.
5)alc technology be used to provide auto amplitude fixing.
6)module structures, making it convenient for installation, debugging and maintenance.
Welcome to contact us to know more details and thanks for your business opportunity.
Cdma signal repeater including full band repeater, band selective repeater; frequency selective repeater; fiber opital repeater; frequency shifting repeater.
Today we draw your attention to our cdma band selective repeater.
Technical features:
1)receiving and sending separation, low require for ant isolation, making it convenient for installation.
2)mini design with metal cavity filters technology inside.
3)full-duplex & dual-port design, and built-in power supply, making it convenient for installation.
4)allowing for continuous gain adjustment 31db by 1db step.
5)alc technology be used to provide auto amplitude fixing.
6)module structures, making it convenient for installation, debugging and maintenance.
Welcome to contact us to know more details and thanks for your business opportunity
This Mobile phone signal jammer (signal isolator/breaker) product is suitable for where forbid to use mobile phone.
CDMA 870-880 33 8dBm/30KHz
GSM 930-960 33 5dBm/30KHz
DCS 1805-1880 33 2dBm/30KHz
PHS 1900-1990 33 2dBm/30KHz
3G TD-SCDMA 2010-2025 33 2dBm/30KHz
3G WCDMA and CDMA2000 2110-2170 33 2dBm/30KHz
Power Consumption :36W
Size : 251*140*52MM
Power supply: AC: 110-240V DC: 4.2V 8A
Jaming Range :2-50(diameter) meters (according to the mobile operatorsí» signal condition )
Work Temperatureú¦-40degree to +55 degree
Application:
Audio-visual areas: theater, cinema, concerts, library, studio, auditorium, etc.; Security Privacy: prison, court, examination room, meeting room, funeral parlor, government agencies, financial institutions, embassies, etc.; health and safety: industrial plant and production shop, gas station, gas stations, hospitals, etc.
1. Conference room, autitoriums, law court, library, exam room, school, cinema, theater, and hospital, etc.
2. Oil Station, gas filled station, oil field, oil depot, etc.
3. At places where using mobile phone is prohibited such as government, military, finance, security, police and command center, etc.
4. Channel types can efficiently provide shield for mobile signals from CDMA, GSM, DCS and PHS.
Function :
1.4-Channel type can efficiently provide shield for mobile signals from CDMA, GSM, DCSú¼3Gú¼WCDMA and CDMA2000.
2. It only shields the signals from mobile phone and does not affect the normal operation of other electronic devices.
3. Switching on, it can work stably for a long time.
5. Slow start-up circuit can avoid sparkling caused by mechanical switch.
Power Consumption :36W
Size : 251*140*52MM
Power supply: AC: 110-240V DC: 4.2V 8A
Jaming Range :2-50(diameter) meters (according to the mobile operatorsí» signal condition )
Work Temperatureú¦-40degree to +55 degree
Keeps you away from noise or disturbance of unexpected cellular phone calls. It can paralyze cellular phone signals within an effective area. And all the specified frequency bands will be blocked simultaneously. It can be applied at meeting room, conference room, museum, gallery, theater, concert hall, church, temple, restaurant, classroom, training center, factory, bank, train, and bus, for some locations of special purpose such as hospital, and gas station. It is easy to install and operate the device. No adjustment is needed. If not well paralyze happened, please change the installation location or position or to check if any cellular control stations or repeaters installed just in nearby.
Product description
We professional manufacturer followings products since 1995:
*gsm fullband/band selective signal booster,
*cdma fullband/band selective signal booster,
*dcs fullband/band selective signal booster,
*gsm&dcs dual band signal booster
*pcd fullband/band selective signal booster,
*wcdma fullband/band selective signal booster
Today, we would like to introduce gsm&dcs dual band signal booster:
*technical features:
1)high system gains.
2)full duplex and double-end design, external power supply, and convenient installation.
3)alc technology with auto-steady function adopted.
4)provide power indication and uplink and downlink indications.
5)with the amplified linear power, the intermodulation and spuriousness are suppressed effectively.
6)the reliability conforms to gb6993-86 standards.
7)the electromagnetic compatibility conforms to ets300 609-4 standards.
Welcome to contact us to know more details or check following parameters
Product Description
Perhaps everyone has run in with the pesky things at least one time. You are on a phone having a deep conversation, and all of a sudden, the person on the other end is no voice anymore. Have you ever wondered what actually causes dropped calls Maybe the phone is too far away from the cell tower, or you are using a phone inside a car or a building, or the bad weather condition, or you are in a dead zone. Whatever, today the dual band mobile phone signal repeater could solve your all problems.
The cell phone signal booster is receiving the signals from base station and transmitting it to our cell phone. This can amplify a wide range of mobile phone signal which up to 1000 square meters. And this device is an effective equipment which design to pick up the outdoor. Connect to the device you can improve the signal of your mobile phone. The uplink and downlink are GSM800 and PCS1900 signals. There are lots of reasons to use this booster, just check out the product specifications and product notes as below. It will be your best choice.
Notes:
Long range Mobile Phone Signal Repeater! Up to 1000 square meters!
This device is for CDMA800 and PCS1900 signals only. Please check frequency your country uses before purchasing
Specifications
Frequency range:
-Up link CDMA 824-849/PCS1850-1910(MHz)
-Downlink CDMA 869-894/PCS1930-1990(MHz)
Coverage: Up to 1000m2 (Distance will be reduced when obstacles are in the way i.e. surrounding walls)
Gain (dB):
-CDMA/PCS Up link 65/53
-CDMA/PCS Downlink 70/58
Gain adjustable range MGCâ?¥30dB
Pass band ripple:
-CDMA:4 dB
-PCS:15 dB
Power supply: AC110220V±10% 4555Hz
Dimensions: Signal Booster: 158 x 136 x 37 mm (L x W x D)
Reliabiity: To zhe GB6993-86 standard
Electromasnetic compatibility: To zhe ETS300 694-4 standard
Color:White
Accessories:
Signal Booster
Indoor Antenna
Outdoor Antenna
Power Adapter
Coaxial Cable 2M
Coaxial Cable 10M
Indoor Antenna Accessories and Screws
The signalwing's j3f-a-20 is specially designed for small or medium sized indoor area, such residential, offices, inner large building or suburb low traffic location with poor connection. Elegant in it's design, it's one of the best cost effective solutions.
The j3f-a-20 mini repeater works sufficiently and reliably to optimize cell phone reception for any relevant system in gsm, cdma, wcdma or 4g lte. System status is clearly visible by led indicators. The light weight and compact size makes it ideal for easy installation. The coverage of j3f-a is ranging from 500~1500 square meters due to different
5. Automatic gain control and manual gain control.
6. Intelligent mode setting, automatically set the values.
7. Auto shut off function available to avoid the damage and interference in unusual signal conditions.
8. Easy installation & maintenance.
9. Extend cell phone battery life.
Power supply Ac:110~240v; dc: 9v/4a
Operating temperature -10¡æ~50¡æ
Environment conditions Ip30
Dimensions (d x w x h ) 186*122*65mm
Weight ¡ü2kg
n control.
5. Intelligent mode setting, automatically set the values.
6. Auto shut off function available to avoid the damage and interference in unusual signal conditions.
7. Easy installation & maintenance.
8. Extend cell phone battery life.
Power supply Ac:90~265v; dc: 9v/4a
Operating temperature -10¡æ~55¡æ
Environment conditions Ip30
Dimensions (d x w x h ) 191*296*76mm
Weight ¡ü5.5kg
Features:
1. Superb linear performance.
2. High output power with water-resist housing.
3. Designed for outdoor application.
4. Automatic gain control and manual gain control.
5. Easy installation & maintenance.
6. Extend cell phone battery life.
Power supply Ac:110~220v; 50/ 60 hz
Operating temperature -25¡æ~50¡æ
Environment conditions Ip65
Dimensions (d x w x h )453.6*357.8*159.7 mm
Weight ¡ü22kg
Product Description
Are you seeking a cell phone booster in the market for your home, office, or car? Are you looking for information on the different types of cell boosters, which brands are the best, and how to install and operate your cell signal booster? There is a dual band mobile phone signal booster available for use with dual band phones.
A mobile phone repeater will allow you mobile phone to be a true wireless device. Once you get a booster, you will be able to throughout you whole house without having worry about dropped calls and little sound volume. That is capable of improving the signal strength of the GSM900 and DCS1800 phone through signal amplification up to an area of 1000 square meters. That means the cell phone booster help you to achieve long distance and more reliable communication.
Having a dual band cellular phone booster youll get a perfect connection and communication. If you are in a weak signal area, the mobile phone signal booster can enhance the signal strength. It is worth to possess, you deserve it.
Notes: Long range Mobile Phone Signal Repeater! Up to 1000 square meters!
This device is for GSM900 and DCS1800 signals only. Please check frequency your country uses before purchasing
Specifications
Frequency range:
-Up link GSM 890-915/DCS1710-1785(MHz)
-Downlink GSM 925-960/DCS1805-1880(MHz)
Coverage: Up to 1000m2 (Distance will be reduced when obstacles are in the way i.e. surrounding walls)
Gain (dB):
-GSM/DCS Up link 65/53
-GSM/DCS Downlink 70/58
Gain adjustable range MGC30dB
Pass band ripple:
-GSM: 4 dB
-DCS:15 dB
Power supply: AC110220V±10% 4555Hz
Dimensions: Signal Booster: 158 x 136 x 37 mm (L x W x D)
Reliabiity: To zhe GB6993-86 standard
Electromasnetic compatibility: To zhe ETS300 694-4 standard
Color:Grey
Accessories :
Signal Booster
Indoor Antenna
Outdoor Antenna
Power Adapter
Coaxial Cable 2M
Coaxial Cable 10M
Indoor Antenna Accessories and Screws.
ECG cables also referred to as an ECG patient cable, is a type of cable connection designed for non-invasive heart monitoring, typically used to help diagnose potential heart issues. The ECG cable connects to electrodes which are positioned at specific locations on the patient�¢??s body to detect and record heart muscle electrical activity. The cables then transmit the electrical activity back to the ECG device for analysis and diagnosis by medical professionals.
ECG Cable Feature
[Multiple Leads]: ECG cables usually have several leads placed in specific areas on the patient�¢??s body, such as the chest, arms, and legs, to measure the heart�¢??s electrical activity from different angles.
[Durability]: ECG cables are constructed from top-quality, sturdy materials that can endure repeated bending, tugging, and
twisting without sustaining any damage. This ensures that the cables can withstand the rigors of frequent use and remain reliable over time.
[Shielding]: ECG cables are shielded to block out external electrical signals, which can interfere with the accuracy of the
readings.
[Connector Compatibility]: The ECG cables are available with various connector types, including snap, clip, and banana, to fit different types of ECG machines.
[Safety]: ECG cables are designed to meet strict safety standards and regulations to ensure patient safety. This helps to ensure that patients are protected from any potential harm during the monitoring process.
[Cleaning and Disinfecting]: The ECG cables are easy to clean and disinfect to maintain hygienic conditions, as they come into contact with the patient�¢??s skin.
ECG Cable Advantages
[Excellent Performance]: ECG cables are built to withstand the rigors of twisting and bending, and have been thoroughly tested to ensure optimal performance. The cables are also equipped with electrical shielding to protect the signal integrity, ensuring accurate readings.
[Non-Invasive]: ECG cables are non-invasive, which means that they do not require any incisions or invasive procedures. This reduces the risk of infection and makes the monitoring process much safer for patients. Instead, the cables are simply attached to the patient's skin, making it a quick and painless process.
835 15Dbm Mobile Signal Repeater Booster Suppliers
Short on time? Let 15Dbm Mobile Signal Repeater Booster sellers contact you.
