We Al Rayhan Exports Group are the manufacturer and exporter of the Ball Valves, Gate Valves, Globe Valves, Check Valves, Pipe Strainers, Industrial Valves, Safety Relief Valves, Pressure Reducing Valves and Digital Pressure Relief Valve. Our factory is Located in Ahmedabad,Gujarat.Factory visit also available for the buyer.We are commited to provide best quality and services.
All types of Valves are available with extremely high-quality raw materials which can be offered in varied sizes, shapes, and surface finishes, and all our products are shipped with assured quality and authenticity checks. Types of valves : Ball valve, Butterfly valve, Industrial valve, Needle valve, Manifold valve, Monoflange valves, Knife gate valves, Gate valve, Globe valve, Check Valve, Plug Valve, and more on demand
A butterfly valve is a shut-off valve with a relatively simple construction. In closed position, the disc blocks the valve bore while in open position, the disc is turned to allow flow. A quarter turn takes the valve from fully open to fully closed position, or opposite, and thus the butterfly valve allows for quick opening and closure. Butterfly valves can be used for a broad range of applications within water supply, wastewater treatment, fire protection and gas supply, in the chemical and oil industries, in fuel handling systems, power generation etc. Some of the advantages for this type of valve are the simple construction not taking up too much space, and the light weight and lower cost compared to other valve designs. The valves can be operated by handles, gears or actuators according to any specific need.
Check valves are basically the type of valves which prevent the backflow of the fluid or gas traveling through that specific pipeline. The liquids or gases flowing through non-return valves flow in single direction mainly. These poppet check valves consist of two openings which mainly allows the fluid or gas to enter from one end and leave from the other end. If the flow turns and no check valve is installed, water hammer can occur. Water hammer often occurs with an extreme force and will easily damage a pipeline or components. Check valves are used in many different applications. For example they are often placed on the outlet side of a pump, to protect the pump from backflow. Centrifugal pumps are not self-priming, and therefore check valves are essential for keeping water in the pipes. Also, check valves are very often used in HVAC-systems (Heating, Ventilating and Air Conditioning-systems).
A globe valve is a linear motion valve used to stop, start, and regulate the fluid flow. The globe valve disk can be removed entirely from the flow path, or it can completely close the flow path. During the opening and closing of the valve, the disc moves perpendicularly to the seat. Leakage from the globe valve seat is less as compared to the gate valve, mainly due to right angle contact between the disc and seat ring, which allows tighter seal between seats the disk. Globe valves consist of a movable disk-type element and a stationary ring seat in a generally spherical body. The valve stem moves a globe plug relative to the valve seat. The globe plug can be at any position between fully opened and fully closed to control flow through the valve. The globe and seat construction gives the valve good flow regulation characteristics. Turbulent flow past the seat and plug, when the valve is open, results in a relatively high pressure drop, limited flow capacity, and low recovery.
A gate valve is generally used to completely shut off fluid flow or, in the fully open position, provide full flow in a pipeline. Thus it is used either in the fully closed or fully open positions. A gate valve consists of a valve body, seat and disc, a spindle, gland, and a wheel for operating the valve. A gate valve can be defined as a type of valve that used a gate or wedge type disk and the disk moves perpendicular to flow to start or stop the fluid flow in piping. A gate valve is the most common type of valve that used in any process plant. It is a linear motion valve used to start or stop fluid flow. Therefore, there is little pressure drop or flow restriction through the valve. Gate valves are used in many industrial applications including the oil and gas industry, pharmaceuticals, manufacturing, automotive, and marine. Gate valves are not suitable for throttling purposes.
A knife gate valve is a component that utilizes a blade to cut through clogging of heavy liquids; whereas a slide gate valve is a component utilizing a slide plate in order to better manipulate or control the flow of dry bulk material. The Knife Gate Valve provides reliable shut-off for both dry and wet line fluids. The bonnet-less valve equipped with a heavy-duty gate to cut though both dry and wet line fluids. The valves find application in paper and pulp, minerals and metals, steel plants, thermal power plants and chemical/ petrochemical industries. The versatile metallic and resilient seats for bidirectional and unidirectional applications. The versatile metallic and resilient seats for bidirectional range is available in wafer, lugged and flanged configurations.
Monoflange valves are used as an alternative to a system which has multiple valves. They are designed specially to provide a compact installation for transmitter and gauge instruments. In an application where a monoflange is used, it is used toreplace other equipment. For instance, rather than having one valve and relying on it to close so that you can isolate the transmitter, two different valves can be used. In such case, a monoflange valve would replace two different valves perfectly. With this, you won't need to have two different valves but a single one. This is because the monoflange is composed of two different closed valves as well as a vent which is opened so as to limit the pressure which is between them. It also has a reduced weight as well as minimal leak paths thereby providing a higher integrity system
Ball Valves are used in a wide variety of high pressure applications. Two factors make them popular. First, a full unrestricted flow that allows no product restrictions through the valve. Second, the three piece design and the removal of a minimal number of bolts allow service to be performed without removing the complete valve from the line. We offers a range of high pressure valves that are also great for use as blowdown valves. Our product range also includes ball valve components and a variety of valve parts that ensure quick assembly, repair and use of your fittings. Two way ball valves manufactured by us will be various Sizes, End connections and Pressure Ratings as per customer requirements. Manual and Pneumatically actuated valves are also manufactured by us.
The manifold valves are manufactured to endure all differential pressure and liquid level application needs. Manifolds Valve is designed for static pressure and liquid level applications. These manifolds are available in traditional and compact body designs. Manifold connections include female tube fittings, pipe ends (NPT and ISO 228/1), and flanges (MSS SP-99) in 1/2 and 3/4 in. and 12 mm sizes The units are available in 2 valve manifold, 3 valve manifold, and 5 valve manifold product designs.The 2 valve units are designed to withstand static pressure in an industrial setting. The 3 level and 5 level valve units are expressly designed for the purpose of surviving and maintaining the differential pressure applications. The units have been designed with a temperature rating with operating parameters which range up to 232 C with packing of PTFE and optional 428 C with packing of graphite. The units are designed and manufactured to withstand a pressure parameter rating of up to 6000 PSIG.
Needle valves are usually used in flow-metering applications, especially when a constant, calibrated, low flow rate must be maintained for some time, such as the idle fuel flow in a carburetor. Needle valves sometimes referred to as plunger valves. A needle valve has a relatively small orifice with a long, tapered seat, and a needle-shaped plunger on the end of a screw, which exactly fits the seat. These needle valves are an ideal option for isolating or throttling applications. The self centering, non rotating stem ensures perfect seating. The rigid design gives repetitive bubble tight shut off, easy.s. Our range of needle valves has been designed with durability and performance in the spotlight. These needle valves are available in a variety of sizes (1/4, Â½, 1/8 inch). Our range of needle valves has been designed with durability and performance in the spotlight. These needle valves are available in a variety of sizes (1/4, Â½, 1/8 inch).
Zeal Consultants is your one- stop destination for Industrial valve. We are manufacturing of these valves using cut-edge technology, latest methodologies and best equipments. We always offer new and best range of products to our clients
We take this opportunity to introduce Shree Bhadra Abrasives & Accurate Marketing as one of the leading specialized TEAM OF ENGINEERS, manufacturer & Supplier of Industrial Products Our Main Promoter having practical experience in DESIGN & MAINTENANCE Department in his service period PRODUCTS:- BALL VALVE , GATE VALVE, SAFETY VALVE, BUTTERFLY VALVE, PNEUMATIC BUTTERFLY VALVE , CHECK VALVE , Y STRAINER , FOOT VALVE , TANKER VALVE , FLOAT VALVE These Valves and Cocks are used in water, oil, gas, petrochemical, steam and many other industrial segments and have gained high potential from our customers. Our product range available in screw & flange end meets the standard ISI , IBR , BS , ISO , DIN , ASME , BIS
Ball Valves Screwed / Socket Weld / Butt-weld / Flanged Ends : Ball valves are designed and manufactured to provide maximum service life and dependability. Three Piece and Two Piece design Ball Valves ensure efficiency, reliability and economy. Pneumatic Operated Ball Valves and Electrical Actuated Ball Valves are maintenance friendly and suitable for on-line maintenance . Butterfly Valves High Performance Butterfly Valve 150LB/300LB/600LB ,wafer type with integrally moulded elastomeric body sleeve are designed for longer life and trouble free performance. Gate Valves ATSIPL distributes a full line of Gate Valves, including Wedge Gate Valves, Knife Gate Valves, Lined Gate Valves, Resilient Seated Gate Valves and more. Gate Valves are available from 1/2â?³ through 24â?³ and larger in various material options.
Approx. Price: Rs 250 / Unit We are a renowned name in offering a wide assortment of Intervalve Rubber Lined Butterfly Valves.