ES EL12 is a copper-coated, mild steel wire for submerged arc welding.
It can be combined with the following fluxes:
ES FLUX 171, ES FLUX 180
ES FLUX 181 and ES FLUX 900.
ES EL12 is especially for use in combination with ES FLUX 180 and ES FLUX 181 in the shipbuilding industry, for the butt welding in material from 10 to 30 mm thickness and especially thin plate (e.g. LPG cylinder).
ES FLUX 900 is a basic agglomerated, slightly Si- and Mn-alloying fux for submerged arc welding, specially designed for fillet welding and for the single- and multi-pass butt welding of mild, medium and high tensile steels.
ES FLUX 900 is of the aluminate basic type and, for this slag system, it has a very high current-carrying capacity on both AC and DC and very good operating characteristics.
ES FLUX 900 is ideally suited to narrow gap welding due to the excellent slag detachability and smooth side-wall blending.
ES FLUX 171 is a basic agglomerated, slightly Si- and Mn-alloying fux for submerged arc welding, specially designed for fillet welding and for the single- and multi-pass butt welding of mild, medium and high tensile steels.
ES FLUX 171 is of the aluminate basic type and, for this slag sys- tem, it has a very high current-carrying capacity on both AC and DC and very good operating characteristics.
ES FLUX 171 is ideally suited to narrow gap welding due to the excellent slag detachability and smooth side-wall blending.
ES FLUX 161 is designed for the single-wire, multi-run butt welding of mild, medium and high tensile steels with impact strength requirements down to -40C/-60C.
Due to the non-alloying effect, ES FLUX 161 is designed for use with a suitable alloying wire. ES FLUX 161 can be used on DC.
ES FLUX 900 is a basic agglomerated, slightly Si- and Mn-alloying fux for submerged arc welding, specially designed for fillet welding and for the single-and multi-pass butt welding of mild, medium and high tensile steels. ES FLUX 900 is of the aluminate basic type and, for this slag system, it has a very high current-carrying capacity on both AC and DC and very good operating characteristics.
ES FLUX 900 is ideally suited to narrow gap welding due to the excellent slag detachability and smooth side-wall blending.
Density
231 Industrial Machinery Plants Suppliers
Short on time? Let Industrial Machinery Plants sellers contact you.
ES FLUX 180 is designed for use in the single-and multi-pass butt welding of mild and medium tensile steels where moderate impact strength is required.
ES FLUX 180 is of the calcium-silicate type with a very high current-carrying capacity, even at low welding speeds with both AC and DC.
ES FLUX 180 is excellent for the butt welding of materials from 10 to 30 mm thickness and is used in the shipbuilding industry, for example.
ES FLUX 180 is specially designed for use in combination with ES EL12 or ES EM12 in single- or multi-wire systems.
ES FLUX 171 is a basic agglomerated, slightly Si- and Mn-alloying fux for submerged arc welding, specially designed for fillet welding and for the single and multi-pass butt welding of mild, medium and high tensile steels. ES FLUX 171 is of the aluminate basic type and, for this slag system,
It has a very high current-carrying capacity on both AC and DC and very good operating characteristics.
ES FLUX 171 is ideally suited to narrow gap welding due to the excellent slag detachability and smooth side-wall blending.
ES EA4 is a manganese-alloyed, copper coa-ted wire for the submerged arc welding of medium- and high-strength structural steels.
ES EA4 should preferably be used together with non-alloying or slightly alloying fuxes, such as ES FLUX 161, when high weld metal quality requirements must be met.
ES EA4 Submerged arc welding wire (SAW) for joining fine grain and high temperature resistant steels, structural steels, steels for shipbuilding, steels for pressure vessels, production of steel pipes up to grade X80, high-strength steels, etc.
ES EA4 can be combined with ES FLUX 161, ES FLUX 171 and ES FLUX 900.
ES EA2 is a copper-coated, molybdenum-alloyed wire for the submerged arc welding of non-alloyed and low-alloyed steels.
ES EA2 Submerged arc welding wire (SAW) used for joining fine grain steels resistant to high temperatures, structural steels, construction naval vessels, pressure vessels, shipbuilding steels, pipes and pipeline steels up to grade X70, etc.
ES EA2 can be combined with ES FLUX 161, ES FLUX 171 and ES FLUX 181.
ES EM12 is a copper-coated, semi-killed wire for the submerged arc and electro-slag wel ding of medium and high strength structural steels.
It can be combined with the following fluxes:
ES FLUX 171, ES FLUX 180
ES FLUX 181 and ES FLUX 900.
ES EM12 can be applied both for high-speed welding steel plate of 450-500 MPa tensile stren-gth steel (e.g. boiler, bridge, pressure vessel, and LPG cylinder).
ES FC 316LT is a fux-cored wire for the out-of-position welding of 316 and 316L type stainless steels where increased resistance to pitting corrosion is required.
This is particularly relevant when it comes to attack by chloride solutions and sulphuric acid.
The weld metal composition is such that the stabilised 321 and 347 stainless steels may also be welded.
ES FC 308LT is a rutile, fux-cored wire, speci�cally designed to operate in the vertical and overhead positions when welding 304, 304L, 308 and 308L stainless steels.
The stabilised 321 and 347 steels may also be welded.
Typical application: welding 304L and other common 18/8 stainless steels, Nitrogen bearing 304LN and titanium stabilized 321 and General fabrication including piping, tanks, and pressure vessels
ES 81T1-Ni1M is an all-positional, rutile, fux- cored wire for good toughness down to -40C.
The wire contains 1% nickel and has exceptional operating characteristics in all positions with high deposition rates. Shielding gas Ar + 20% CO2 or CO2. ES 81T1-Ni1M is designed for the all-posit-ional welding of carbon-manganese and low-alloy steels.
Typical applications: offshore fabrications, vessels and structural steel work.
ES 71T1M is a fux-cored, tubular wire designed as a truly all-positional, general-purpose wire for welding mild and medium tensile steels up to 510 MPa tensile strength.
Using either Ar/CO2 or CO2 as the shielding gas, the 1.2 and 1.4 mm sizes can be used in the vertical position on spray transfer providing for maximum deposition and time savings.
Weld pool control is easy both vertically up and downwards and slag removal is rapid. ES 71T1M is designed for a wide range of applications especially where manipulation of the work is impractical.
ES 71T1M is a Fux-cored, tubular wire designed as a truly all-positional, general-pur pose wire for welding mild and medium tensile steels up to 510 MPa tensile strength.
Using either Ar/CO2 or CO2 as the shielding gas, the 1.2 and 1.4 mm sizes can be used in the vertical position on spray transfer providing for maximum deposition and time savings.
Weld pool control is easy both vertically up and downwards and slag removal is rapid.
ES 71T1M is designed for a wide range of applications especially where manipulation of the work is impractical.
ES MIG 5356 is the most widely used welding alloy and can be classified as a general-purpose type filler alloy.
ES MIG 5356 is typically cho- sen because of its relatively high shear strength.
The 5XXX alloy base material, welded with ES MIG 5356, with a weld pool chemistry greater than 3% Mg and service temperatures in excess of 65�°C, is susceptible to stress corrosion cracking.
ES MIG 5183 is designed to provide the highest possible strength in the as-welded condition of alloy AA 5083 and similar high-magnesium alloys.
The more common ES MIG 5356 typi- cally fails to meet the as-welded tensile require- ments of AA 5083.
The alloy is typically used in marine and structural applications where high strength, high fracture toughness for impact resistance and exposure to corrosive elements are important.
The alloy is not recommended for elevated temperature applications due to its susceptibility to stress corrosion cracking. The alloy is non-heat treatable.
231 Industrial Machinery Plants Suppliers
Short on time? Let Industrial Machinery Plants sellers contact you.
