Consistent control is available by always maintaining the standard time in application of GPS receipt for compensating the present time to the electronic Guard Lamp switch, and this product does not require a separate compensation because the light On/Off time according to the region is compensated automatically.
Consistent control is available by always maintaining the standard time in application of GPS receipt for compensating the present time to the electronic Guard Lamp switch, and this product does not require a separate compensation because the light On/Off time according to the region is compensated automatically.
The front panel of this device consists of the subject part, an output screen, and the power supply. It is a lamp controller that has a programmable date (year, month, day, hour, and minute)to find the sunrise and sunset time. You can adjust various data in real time while seeing the LCD display.
This device is a lamp controller that has a programmable date (year, month,day, hour, and minute) to find the
Sunrise and sunset time. In cases in which the area of the controlled region is narrow or the number of Streetlamps to be controlled is small, it is economical to use due to its automatic switches.
2606 Electronic Switches Suppliers
Short on time? Let Electronic Switches sellers contact you.
Detector Switches is applied to low current circuit (Secondary circuit) push switch
used for electronic equipment.
Appearance of the Switch shall have good finishing and shall have no rust, crack of plating failures.
Terminal Strength of a static load of 3N(306 gf) shall be applied to the tip of terminal in a desired direction for 1 minute. The number of test shall be once per terminal.
Hook Switch is applied to low current circuit hook switch for electronic equipment.
The standard test conditions shall be 5~35 in temperature, 45~85% RH and 860~1060 m bar.
Storage temperature range : 30 degree Celsius to 80 degree Celsius, however 96 hours maximum for continuous storage over a range
Tact Lever Switches is applied to low current circuit push switch for electronic equipment.
Appearance of the Switch shall have good finishing, and no rust, crack or plating failures.
Operating force of a static load shall be applied to the tip of actuator in operating direction.
Robustness of terminal of a static load of 2N(200gf) shall be applied to the tip of terminal
in a desired direction for 1min. the test shall be done once per terminal.
Tact Switch MT 1101 SE is applied to low current circuit tactile switch for electronic equipment.
Storage temperature range 96 hours maximum for continuous storage over a range
The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
Micro Switch action is PUSH-ON TYPE S.P.D.T
Contact resistance measurements shall be made with a 1KHz ± 200Hz max
DC 5V 1A contact resistance meter.
Insulation resistance measurements shall be made following application of DC 500 V potential across terminals and across terminals and frame for one minute.
The travel distance for the plunger to come to a stop shall be measured
Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Snap-in type, can be mounted directly on PC board.
Some of output terminals can be also used as jumper leads, thus making circuit arrangement easy.
Available with anti-ESD ground terminal.
Although the recommended PC board thickness is 1.6mm, the models which can be mounted on PC boards of thickness 0.8 to 1mm are also available upon request.
Tact Switch MT 1101 S is applied to low current circuit tactile switch for electronic equipment.The standard test conditions shall be 5 ~ 35 degree Celsius in temperature.
45 ~ 85% RH and 860 ~ 1060 m bar in atmospheric pressure.
Should any doubt arise in judgement, tests shall be conducted at 20±2 degree Celsius, 60±5% RH
Tact Switches MT 1102 VS is applied to low current circuit tactile switch for electronic equipment .Contact resistance measured DC 5 V 1 A or by ohmeter allowing a small current at 1 kHz with a load of twice of the Actuating force
Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
Tact Switches MT 1101 U is applied to low current circuit tactile switch for electronic equipment.
Contact resistance measured DC 5V 1A or by ohmeter allowing a small current at 1 kHz with
a load of twice of the Actuating force
Insulation resistance DC 100V is applied between terminals and between terminals and cover for 1 minute ± 5 seconds
250A1-HS-H04M To FH25001-02(R,430MM)/ FH25001-02(L,140MM)
250A1-HS-H04M FH25001-02(R,430MM)/FH25001-02(L,140MM)
2.50MM 4P To 2P/2P UL10530 26AWG N PVC Free(TPE)
Jinsung Electronics, founded in 1995, manufactures RF/Flexible PCB, which are the most basic main board of electronic products that are closely related to our daily life.
Jinsung Electronics produced flex and rigid-flex printed circuit boards that assisted physicians and healthcare professionals to offer more functions, operational easiness, and smaller size packages through innovation and collaboration with customers.
3D modulator is electronic polarized modulator that electronically switches the polarization angle of light passing through it.
In optimization with Silver screen and single-lens 3D stereoscopic projector, this filter provides high brightness and low crosstalk using inexpensive passive 3D eyewear.
2606 Electronic Switches Suppliers
Short on time? Let Electronic Switches sellers contact you.
