DATA SHEET FOR EPOXY EPOXY COATING :- INTRODUCTION - EPOXY COATING (HYB) is a two part high solids solvent free epoxy phenolic resin based coating system designed for hard wearing, smooth surface finish for floors, walls and on steel structures. Nonskid surface finish can be achieved on floor, if required. FEATURES: 1) Hard Wearing 2) Non Dusting 3) Excellent Surface Finish 4) Non Smelling 5) Good Aesthetics 6) Highly Chemical Resistant APPLICATION: 1.Stir well before mixing Part A and Part B and mix in the prescribed ratio. 2.Apply one coat of EPOXY primer on the clean and dry surface. 3.EPOXY COATING (HYB) should be applied on the surface by brush or roller within 24 hrs. After application of primer coat it should be allowed to air dry for min. 4 hrs. Preferable in a dust free atmosphere. 4.Apply min. 2 coats with the intercoat interval of 6-8 hrs. PRODUCT SPECIFICATIONS: Application - Brush, Roller Mixing Ratio - As Directed on Packing Port Life - 30 Mins. Drying Time - Touch Dry- 30 Min, Hard Dry 6 Hrs. - Intercoat Interval 6-8 Hrs. Min. - Dry Film Thickness 125-150 Microns/per coat - depending on porosity Covering Capacity - 6-8 sq.met/kg per coat depending on porosity, roughness & method of application. Color Shades - All Standard Shades RECOMMENDED USES: 1) Food & Pharmaceutical 2) Work Shop 3) Clean Room Application 4) Chemical Resistant Coating for Concrete& Steel 5) Petrochemical, Fertilizer plants METHOD OF APPLICATION: SURFACE PREPARATION The long-term durability of the applied Epoxy coating (HYB) epoxy coating is dependent on the adhesion between sub-base and coating material. It is most important therefore, that the substrate surfaces are correctly prepared prior to application. 1.Before application of the Epoxy coating (HYB) surface should be free from loose partials, rust, oils, grease or earlier coatings and should be totally dry. 2.New concrete or cementations surface should be placed at least 28 days and have a moisture content of less than 5% before application of Epoxy coating (HYB) 3.After surface is dry, all repair work like sealing of joints, cracks filling of cavities and crevices should be carried out. HEALTH & SAFETY - Keep the containers tightly closed when not in use. Avoid contact with skin & eyes. It comes in contact with the body, wash affected parts with plenty of water and contact a doctor. Other known sector for Epoxy floor lining, Epoxy garage floor lining, Concrete epoxy lining, Concrete floor epoxy lining, Epoxy pipe lining, Marine epoxy lining, Sub marine epoxy lining, Basement lining epoxy floor shield, Louisiana, Oregon, Chip lining color epoxy floor, Aviation lining epoxy interior.
Product Description
Place of Origin Guangdong, China (Mainland)
Brand Name EASY ON
Capacity 567ML/can, 12cans/ctn, 2320ctns/20gp container. 4900ctns/40HQ'
Feature Eco-friendly
MOQ 1x20' FCL
Applications To iron the clothes, fabricsï¼? keep the clothes stiff and wrinkle removal
Validity 2 years
OEM OEM service offered & welcomed
Features:
1. Makes ironing easier;
2. Easily removes wrinkles for a crisp;
3. Keep clothes away from wrinkle;
4. No harm to skin and clothes;
5. Highlights all colors;
6. Easy to be absorbed by fabric.
Direction For Use:
1) Shake well before use.
2) Hold can 6-10 inches away from fabric & spray at 45�°angle.
3) Do not spray upside down, which will cause gas pressure lost.
4) Allow enough time for spray to penetrate fabric before ironing.
5) Spray fabric with an even sweeping back and forth motion.
6) Repeat spray for additional crispness.
FAQ
Q1.Are you a factory?
Yes, we are a historical factory for household chemical products and established in 2004.
Q2.Where is your factory located? Can I visit ?
Our factory is located in Shanwei city, about 400 Kilometers away from Guangzhou city , in order to facilitate people to visit us, we set office in Guangzhou city to welcome customers from all over the world to talk business.
Q3. What is the minimum order quantity?
Generally speaking, our MOQ is 1*20GP container, If you have different demand in quantity, we could further discuss it.
Q4.Do you accept OEM, ODM?
� � Yes, we totally accept it. We have professional external packaging designers , customizing private label product is supported, we have a lot of customization experience.
Q5. What are your advantages?
� � � We are manufacturer. Procurement from the source, eliminating the need for middlemen. � We have a long history of production and have our own research and development capabilities. We offer one stop solution and can quickly meet customer needs.
About US
Established in 2004, GuangDong Dream Fine Daily Chemical Co., Ltd is a professional enterprise of daily chemical series products such as insecticide spray, mosquito coil, ironing speed starch, air freshener,etc. We offer one stop solution of research and development, production and sales.Ã?Â
With advanced equipment, high standard of production workshop with automatic packing machines, we can offer high-quality products and close after-sale service. So far, Dream Fine has established trade relationship with customers from many countries in Africa, Middle Asia, South America etc. We are your reliable supplier to support stable superior quality product.
Multi-purpose Spray Paint designed for interior & exterior application.
High Gloss and Quick Drying
Weatherproof, waterproof, rust proof
Acrylic Paint
Solid color and metallic color available
Primer and Lacquer
OEM Private Label acceptable
400ML Capactiy
Standard packing: 12pcs/box
Metal cutting fluid In actual production, even high-quality metal cutting fluids must be added with a certain amount of bactericidal and algae-removing agents to extend the service life and increase the utilization rate. PSC80626, whether used as a metal cutting fluid additive, a settling agent or a water-based cutting fluid, can accelerate the sedimentation of metal chips, accelerate the separation of water and oil in the cutting fluid, effectively reduce the growth of bacteria, and extend the life of the metal cutting fluid. PSC80626 is used in fully synthetic metal cutting fluids for water machines, and the amount is very small, and the additive formula can be adjusted flexibly. As a settling agent, it is basically consistent with Buckman's Busan 77 in terms of theoretical map test data, which can completely replace this type of product and has a significant effect in actual use.
1, With very good adhesion, can dissolve much iron oxide in metal surface, makes very strong combination with metal body.
2, Can be combined with cover coat in high level.
3, With very good elasticity and compressive strength. Prevent and decrease damage due to mechanical stress.
4, With less viscosity and surface tension, its good for escape of gas when firing. Reduce bubbles on cover coat. To ensure the smooth surface of enamel products.
5, With suitable expansion coefficient similar as steel plate.
ABOUT US
vitreous enamel coating porcelain enamel steel grates enamel glaze fritHunan Noli Enamel Co., Ltd
is the leader manufacturer of enamel frits & inorganic pigment in China.
Now we have 30,000 M/T enamel frits and 2,000 M/T inorganic pigments annual capacity, 10,000 M/T RTU(Ready to use) powder and electro static powder.
Our main products of enamel frits including ground coat, cover coat, transparent frit , matt enamel, direct on black frits and various cast-iron frits. High temperature inorganic pigment including Red& yellow, blue, green, black Oxide etc, widely used in porcelain enamel, ceramics, glass, coating,painting etc.
As an ISO9001:2008 certified manufacturer, we have strict quality control in the whole production process to guarantee the quality of products. We are supplying the best service for customer.
100% of Our goods are exporting to USA, Europe, Middle East, Southeast Asia, South America, & Africa.
FAQ
Q1. Are you factory or trading company ?
We are a factory.
Q2. Whats the MOQ ?
Inorganic pigment MOQ is 25kg, enamel frit, RTU powder and electronic static powder MOQ=200kg.
Q3. What is your principle for the samples ?
We offer free samples if you are willing to pay the shipping cost.
Q5. How about your delivery time?
A: Generally, it will take 15 days after receiving your advance payment.
Q6. What information should I let you know if I want to get a quotation?
A: Your base material, your application area (best to send your finished product picture), the physical parameters you require(acid resistance, adherence, color, etc) the quantity you need. If possible, you can send me your samples and we customize for you.
Q7.Why choose us?
1. Reaching a production capacity of 30,000 Tons/Year for Enamel frit, 10,000 Tons/Year for RTU & electronic static powder, 2,000 Tons/Year for Inorganic pigment.
2. 60% frits & pigment exported to US, Netherlands, Indonesia,Thiland, Vietanam, Korea, Chile etc 30 country.
3. Having over 30 technical experts of frits & pigment from domestic & overseas, focusing on technical development & product improvement.
4. Having complete quality control system, Strong technical supporting team is focusing on customer service in this world.
AT-66 is a kind of synthetic emulsion of styrene acrylic copolymer. It is good at water, alkali and scrubbing resistance. It has excellent performance in adhesion with the base materials. Therefore, it is very suitable for interior and exterior wall paints.
Polymer Type Styrene acrylic copolymer
Appearance Milky white liquid
Solid Content 48±0.5%
pH Value 7.0-9.0
Viscosity 800-2000 cps(Brookfield Viscometer , 3#/60rpm/25)
Average Particle Size 0.1 - 0.2 micron
Glass Transition Temperature About 25
Minimum Film Temperature About 18
Ionic Character Anionic
Applications
AT-66 can be used for interior and exterior wall paints.
At-3202A is a kind of styrene acrylate copolymer synthetic latex, without APEO and plasticizer, with good cement compatibility, water resistance, alkali resistance and excellent elongation AT break, especially suitable for the preparation of high-performance JS waterproof coating.
Appearance :milk white liquid
Solid content:54.5%-55.5%
PH: 7.0-9.0
Viscosity:500-2000 cps(3#60 rpm/25 centigrade)
Particle size :0.2-0.3 micron
Tg:-16 centigrade
MFT:0 centigrade
Ion features:anion
Use :make high performance JS water proof coating ,flexible putty.
At-3128 is a kind of vinegar tertiary acrylate copolymer, which is used to produce synthetic latex of water-borne metal antirust primer coating, and has good compatibility with antirust agent and antirust pigment.The products have excellent adhesion with metal substrate, resistant to water, salt water, salt fog, acid and alkali resistance.It has high weather resistance and yellowing resistance, suitable for metal rust - proof primer.
Appearance:milk white liquid
Solid content: 39%-41%
PH: 7.5-8.5
Viscosity: less than 1000 cps(3#60rpm/25 )
Particle size:0.0-0.2 micron
Tg:23
MFT:10
Ion feature :anion
Excellent weather resistance;
Excellent light retention and color retention. Good chemical resistance and water resistance;
With appropriate primer, good adhesion;
Fast drying, good leveling, strong covering power;
Wide range of application, good matching, can be matched with a variety of primers and used for a variety of material surface.
1424 Paints Coatings Suppliers
Short on time? Let Paints Coatings sellers contact you.
