Bitumen 60/70 is a penetration-grade paving bitumen widely used in road construction, asphalt production and infrastructure projects. It is a dark, viscous petroleum-derived binder with a penetration range of 60 - 70 dmm, providing a practical balance of hardness, flexibility and temperature resistance for general pavement applications. The material can be supplied in new steel drums, jumbo bags or bulk tanker shipments according to project requirements. It is suitable for asphalt concrete, road surfacing, pavement maintenance and waterproofing applications. Each batch can be tested for penetration, softening point, ductility, flash point and other relevant parameters to ensure conformity with agreed specifications and destination-market requirements.
Key Specifications
Product Type: Penetration Grade Bitumen
Grade: 60/70
Penetration at 25 Degree C: 60 - 70 dmm
Appearance: Black to dark brown
Form: Semi-solid / viscous material
Softening Point: Typically around 48 - 56 Degree C, subject to applicable standard
Ductility: According to applicable specification
Flash Point: According to applicable standard
Commodity : Bitumen 50- 70
Type : Eastern European
Penetration : at 25°C (50-70)
Softening Point : at 0°C (46-54)
Resistance to Hardening : at 1630c
Change of Mass % : Max -0.5
Retained Penetration : Min -50
Softening Point After Hardening : Minimum Deg. C-48
Flash Point Minimum : Deg. C230
Solubility Minimum : %99
Kinematic Viscosity : at 135 Deg. C, Minimum mm2/s 295
Delivery : CIF Paranagua Port
Quantity : 200 Metric Ton (MT) Spot for Test ?? Extension 2000 MT Contract for 12 mos.
Specifications: HMS No.1 complies with ISRI 200-202, and HMS No.2 complies with ISRI 203-206, consisting of a minimum of 80% HMS1 and a maximum of 20% HMS2.
The goods are:
Free from toxic chemicals, radioactive materials, explosives, organic matter originating from animals or plants, epidemic disease risks, or medical waste.
Free from bombs, arms, ammunition, mines, shells, cartridges, gas cylinders, or any other form of explosive material.
Free from oil, lubricants, grease, rubber, plastic, asphalt, wood, chemicals, or any non-metallic content or impurities
Bitumen Penetration Grade 80/100 is a standard penetration grade Bitumen usually used as a Paving Grade Bitumen suitable for road construction and for the production of asphalt pavements with superior properties. This grade of Bitumen is mainly used in the manufacture of hot mix asphalt for bases and wearing courses. Penetration Grade Bitumen supplied by ASI GLOBAL TRADE is petroleum grade bitumen, manufactured from fractional / vacuum distillation of crude oil. The Bitumen supplied by ASI GLOBAL TRADE is produced from vacuum residue (short residue) feedstock. Penetration Grade bitumens are specified by the penetration and softening point test. Designation is by penetration range only. The penetration grade bitumens have a thermoplastic property which causes the material to soften at high temperatures and to harden at lower temperatures. This unique temperature/ viscosity relationship is important when determining the performance parameters such as the adhesion, rheology, durability and application temperatures of bitumen.
SPECIFICATIONS :
CHARACTERISTIC TEST METHOD UNIT MIN. MAX.
Specific gravity at 25 C ASTM D70 C 1.01 1.05
Penetration at 25°C ASTM D5 mm 80 100
Softening Point ASTM D36 C 42 52
Ductility at 25 C ASTM D113 Cm 100-
Loss on heating ASTM D6 % 0,5
Flash Point ASTM D92 °C 225
Solubility in Trychloroethyelene ASTM D2042%99
Performance after RTFOT Method Test to ASTN D1754:
-Change in mass (m/m) ASTM2872%-0.5
-Retained Penetration 25C, 100g, 5s (% of original) ASTM D5 %50-
-Increase in softening point ASTM D36 C8
-Softening point after hardening ASTM D36 C45-
LEGAL NOTES
The information, and, in particular, the recommendations relating to the application and end-use of ASI GLOBAL TRADE products, are given in good faith based on ASI GLOBAL TRADE current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with ASI GLOBL TRADE recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchant-ability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the productâ??s suitability for the intended application and purpose. ASI GLOBAL TRADE reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.
Bitumen 60/70Test methodUnitSpecification
Specific gravity @ 25 CASTM D70Kg/cm31.01/1.06
Penetration @ 25 CASTM D5mm/1060/70
Softening point CASTM D36 C49/56
Ductility @25 CASTM D113cm100 min
Loss on heating(wt) %ASTM D6wt %0.2 max
Drop in penetration after heating %ASTM D5-D6%20 max
Flashpoint °CASTM D92C232 min
Solubility in TrichloroethyleneASTM D2042wt %99 min
Spot testA.A.S.H.O.T102Negative
ASI GLOBAL TRADE guarantees that the Bitumen Grades supplies under its offers is produced in compliance to and is in conformity to Standard AASTHO M20-70 and ASTM D946/D946M and meets the following specification requirements.
Bitumen 80/100 Test method Unit Specification
Specific gravity @ 25 ASTM D70 Kg/cm3 1.01/1.06
Penetration @ 25 ASTM D5 mm/10 80/100
Softening point ASTM D36 42/50
Ductility @25 ASTM D113 cm 100 min
Loss on heating(wt) % ASTM D6 wt % 0.2 max
Drop in penetration after heating % ASTM D5-D6 % 20 max
Flash point ASTM D92 250 min
Solubility is CS2(wt) % ASTM D4 wt % 99.5 min
Spot test A.A.S.H.O.T102 Negative
Bitumen 80/100 Test method Unit Specification
Specific gravity @ 25 ASTM D70 Kg/cm3 1.01/1.06
Penetration @ 25 ASTM D5 mm/10 80/100
Softening point ASTM D36 42/50
Ductility @25 ASTM D113 cm 100 min
Loss on heating(wt) % ASTM D6 wt % 0.2 max
Drop in penetration after heating % ASTM D5-D6 % 20 max
Flash point ASTM D92 250 min
Solubility is CS2(wt) % ASTM D4 wt % 99.5 min
Spot test A.A.S.H.O.T102 Negative
Bitumen 120/150Test methodUnitSpecification
Specific gravity @ 25CASTM D70Kg/m31000-1050
Penetration @ 25CASTM D5mm/10120/150
Softening point CASTM D36C38 min
Ductility @25 CASTM D113Cm100 min
Loss on heating(wt) %ASTM D6wt %0.5 max
Drop in penetration after heating %ASTM D5-D6%20 max
Flashpoint CASTM D92C218 min
Solubility in TrichloroethyleneASTM D2042wt %99 min
Spot testâ??Negative
Bitumen 60/70 Test method Unit Specification
Specific gravity @ 25° ASTM D70 Kg/cm3 1.01/1.06
Penetration @ 25 ASTM D5 mm/10 40/50
Softening point ASTM D36 52/60
Ductility @25 ASTM D113 cm 100 min
Loss on heating(wt) % ASTM D6 wt % 0.2 max
Drop in penetration after heating % ASTM D5-D6 % 20 max
Flash point ASTM D92 250 min
Solubility is CS2(wt)ASTM D wt % 99.5 min
Spot test A.A.S.H.O.T102 Negative
Bitumen 40/50 Test method Unit Specification
Specific gravity @ 25° ASTM D70 Kg/cm3 1.01/1.06
Penetration @ 25 ASTM D5 mm/10 40/50
Softening point ASTM D36 52/60
Ductility @25 ASTM D113 cm 100 min
Loss on heating(wt) % ASTM D6 wt % 0.2 max
Drop in penetration after heating % ASTM D5-D6 % 20 max
Flash point ASTM D92 250 min
Solubility is CS2(wt)ASTM D wt % 99.5 min
Spot test A.A.S.H.O.T102 Negative
Bitumen 30/40 Test method Unit Specification
Specific gravity @ 25° ASTM D70 Kg/cm3 1.01/1.06
Penetration @ 25 ASTM D5 mm/10 40/50
Softening point ASTM D36 52/60
Ductility @25 ASTM D113 cm 100 min
Loss on heating(wt) % ASTM D6 wt % 0.2 max
Drop in penetration after heating % ASTM D5-D6 % 20 max
Flash point ASTM D92 250 min
Solubility is CS2(wt)ASTM D wt % 99.5 min
Spot test A.A.S.H.O.T102 Negative
Bitumen 10/20 Test method Unit Specification
Specific gravity @ 25° ASTM D70 Kg/cm3 1.01/1.06
Penetration @ 25 ASTM D5 mm/10 40/50
Softening point ASTM D36 52/60
Ductility @25 ASTM D113 cm 100 min
Loss on heating(wt) % ASTM D6 wt % 0.2 max
Drop in penetration after heating % ASTM D5-D6 % 20 max
Flash point ASTM D92 250 min
Solubility is CS2(wt)ASTM D wt % 99.5 min
Spot test A.A.S.H.O.T102 Negative
