Cm-8y semiautomatic bottle blow molding machine is suitable for producing pet plastic containers and bottles from 10-2000ml. It is widely used to produce the carbonated bottle , mineral water, carbonated drink bottle, pesticide bottle oil bottle cosmetics, wide-mouth bottle etc.
Adopting double crank to adjust mould , heavy locking mould, stable and fast , adopt infrared oven to heat the perform , the perform rotated and heated equally.
The air system has been divided into two parts: pneumatic action part and bottle blow part to meet the different requirements for the action and blow .It can provide sufficient and steady high pressure for blowing large irregular shaped bottles.
The machine is also equipped with muffler and oiling system to lubricate the mechanical part of the machine.
The machine can be operated in the step-by-step mode and the semi-auto mode.
The machine is small with low investment, easy and safe to operate .
Main parameterú¦
Type item unit parameter
Container product material / pet pp pe
Volume l 0.1-2
Theoretical output pcs/h 1200-1600
Preform length mm 15-350
Preform inner diameter mm ª)5-38
Moulding max.Mould plate dimenstion(l x w) mm 350x380
Max.Mould thickness mm 180
Clamping force kn 45
Mould opening stroke mm 16
Machine size and weight main machine (l x w x h) cm 160x60x161
Main machine weight kg 500
Heater (l x w x h) cm 187x63x145
Heater weight kg 250
Power kw 17.5
Cm-a4 full automatic blow molding machine is suitable for producing pet/pe and pp plastic containers and bottles in all shapes. It is widely used to produce the carbonated bottle, mineral water, pesticide bottle oil bottle cosmetics, wide-mouth bottle and hot fill bottle etc.
Reasonable design, full automatic control, save power and labor. Adopt high quality components,
Feeding system carries the performs by robot automatically.
Infrared oven heater adopts the quartz lamp to heat the pet tube.
Fully automatic process with low investment, high efficiency , quick and safe operation , easy for trouble -shooting , maintenance and other benefits.
We have perfect service after sales .
Main parameterú¦
Model cm-a4 cm-a4
Output depend on bottle design 3200-4000pcs/h
+µµ+¦µ+± body diameter 20mm-100mm
Height 50mm-350mm
Neck diameter 15mm-38mm
Mould cavity 4cavity
Mould thick ness 240mm
Mould 500x500mm
Main machine power electrical source power 380v/220v 3phase 50/60hz
Powe r 49kw
Really use power 14kw
Air source lp air compressor 1.6m3/min 1.0mpa 1set(7.5kw)
Hp air compressor 1.0m3/min 3.0mpa 2set(each set 11kw)
Air dryer 2.0m3/min 3.0mpa 1set
Cooling water cooling water 15l/min
Main machine size líßwíßh 1908íß1858íß1920mm
Main machine weight 3600kg
Auxiliary equipment
Pre-form unscrambler is equipped líßwíßh 276íß106íß186mm
Weight 250kg
Rotary blowing method: professionally designed robot sends preform and takes bottle out automatically and accurately.
Convenient operation system: through touching screen operation, it can be changed frequently to adjust the parameter and have the widely operation.
Automatic controlling: adopting precise and swift plc controlling, it has the features of high precision and swift reaction.
Blowing air system: specialized designing of three-work-place and multi-work-place combination valve makes blowing and pulling steady and precise and also keep the blowing effect in a pace all the time.
Mould and replacement: specialized designing of enough tons of lock-mould system and swift load-load-mould structure.It has reliable installation and swift replacement .
Heating device: the intelligence numerical control, feeds back the compensation system automatically, it can show enough the degree and quality of preform heating and keep the bottle mouth protection and cooling heating interchange horizontal line in accordance all the time. Namely ensure the product quality and reduce the production consumption thoroughly
Low noisy sound :reducing-sound machine system, which is designed of circle close and single-path
Baling machine with its trait
1. the machine is suitable for plastic industry, it will prcess the plastic film and plastic bottle ,press it and make solid shape ,it will be convenient to transportation
2. the machine is drived by hydraulic .
3. the machine with independent feeding mouth .it is easily to operate .the feeding mouth with safety protect service ,with high lock quality
4. the machine with automatic discharge system, the baling product will be come out automaticly
Main parameter of baling machine
Baling machine with its trait
1.The machine is suitable for plastic industry, it will prcess the plastic film and plastic bottle ,press it and make solid shape ,it will be convenient to transportation
2.The machine is drived by hydraulic .
3.The machine with independent feeding mouth .it is easily to operate .the feeding mouth with safety protect service ,with high lock quality
4.The machine with automatic discharge system, the baling product will be come out automaticly
1781 Injection Moulding Machinery Suppliers
Short on time? Let Injection Moulding Machinery sellers contact you.
Single shaft plastic shredder character:
1. this machine is suitable to treat the big size of plastic product ,such as big diameter plastic pipe ,pressing plastic film and others
2. The blade base and blade on the rotary roller can be disassembly .it is easy to clean and maintenance.
3. The rotary blade adopt the V design, It can decrease the noise and decrease energy consumption.
4. Each rotary blade with 4 cutting knife edge, when the rotary blade is wear, it can be rotated to 90 degree, then the blade can continues use.
5. Each fixed blade with 2 cutting knife edge, when the fixed blade is wear, it can be rotated to 180 degree, then the blade can continues use.
6. The main axis is drive by gearbox, its running very stably, low noise and strong power.
7. the material push feeding system is hydraulic ways , ,its running very stably
the machine is control by PLC system ,.the blade can rotated in opposite direction ,and also can close automatic if something unexpected happen , with very high safety service
From 160t~420t. This series is rotary table type two injection units and two cores pulls models, suitable for two-component clear-cut products and heterogeneous material products.
1. Energy Saving: greatly reduce cost consumption, lower water and electric costs.
2. High efficiency: high efficiency power system design, quick response, even low speed
has high efficiency performance.
3. High stable operation: closed-loop control system, it is very suitable for precision molding.
4. Quiet: low noise
T series: from 60t~2000t. This series is suitable for all kind dimensions product in high speed molding, such as cap, cup, chair, bucket, large bucket products.
V Series: This series is suitable for mid/ high end general products.
E Series: This is a best selling Series and suitable for precision electronic product, ultra-thin product and ultra-high speed injection molding.
T Series: This series is suitable for all kind dimensions product in high speed molding, such as cap, cup, chair, bucket, large bucket products.
R Series: This series is rotary table type two injection units and two cores pulls models, suitable for two-component clear-cut products and heterogeneous material products.
D Series: This series is suitable for electronic product and is easy to measure, easy for setting. It can last longer life.
ES Series: A newly developed high-tech intelligence model, suitable for high end precision products. This design can accomplish energy-saving, high efficiency, high stable operation and quiet working environment
V Series: This series is suitable for mid/ high end general products.
E Series: This is a best selling Series and suitable for precision electronic product, ultra-thin product and ultra-high speed injection molding.
T Series: This series is suitable for all kind dimensions product in high speed molding, such as cap, cup, chair, bucket, large bucket products.
R Series: This series is rotary table type two injection units and two cores pulls models, suitable for two-component clear-cut products and heterogeneous material products.
D Series: This series is suitable for electronic product and is easy to measure, easy for setting. It can last longer life.
Our plastic rigid flat net machine is dedicated equipment for producing hard plastic flat net with polyethylene (PE) as major raw material, and may manufacture multiple structure and specification products by converting orifice module and sizing device. The equipment is designed and manufactured by our plant upon combining advanced foreign technology with practical domestic situations, which has reasonable structure design, stable and credible performance, and easy operation and maintenance. Hard plastic flat net products from the equipment are widely applied for mattress interlayer, dike landslip-preventive net, subgrade strengthening, plant support net, building safety net, mine canopy guard net, pocket net, as well as packaging net for melon and fruit and vegetables, so it is also called universal net.
Model Unit YZPW-2000 YZPW-2500 YZPW-3000 YZPW-4000
Applicable Material PE,PP PE,PP PE,PP PE,PP
Pressing Machine 65/28 90/25 120/25 150/25
Product Width m 2 2.5 3 4
Power kw 68.4 86.4 180 225
Dimension (Length*Width*Height) m 9.6*2.9*3.4 12*3.1*3.5 16*3.8*4.2 18*5.2*4.8
Note:Special requipment is subject to the agreement of the parties.
Max film width(mm):700 900 1200
Max output(kg/h):90 110 130
Screw diameter(mm):íT45 íT55 íT65
Screw & barrel material:38crmoala
Main motor power(kw):11 15 22
