Find Verified Industrial Pumps Suppliers, Manufacturers and Wholesalers

Pressure:
Maximum pressure: 35 MPa (350 bar)
Rated pressure: 21 MPa (210 bar)
Max. Control pressure: 3.5 MPa (35 bar)
Refueling pressure: 0.8-2.0 MPa (8-20 bar)
Max. Shell pressure: Constant 0.25 MPa (2.5 bar), Peak 0.5 MPa (5 bar)
Speed/Flow:
Max. Output per minute: 69.8 cm
Max. Rotational speed: 2810 min
Min. Rotational speed: 500 min
Rated speed: 1500 min
Weight :78kg

Falcon Premium 200 mm (8) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure and rigidly locked in stainless steel stator shell.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- SS-304 Grade investment casting bowl and SS-304 grade impeller in radial flow series
- 20 Mtr. Head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting pad with carbon plate) to with stand axial thrust
loads
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Special designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures services feasibility
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS Pumps are available

Specification
Direction of Rotation : Counter clockwise from driving end -1ph : Electrically Reversible -3ph
- Power Range : 7.5 kW to 75 kW (10 HP to 100 HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Thrust Load : 7.5 kW -30 kW -10000 lbs
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 440 Mtr.
- Discharge Range : 2400 LPM to 300 LPM
- Outlet Size in Inch : 4.0" & 5.0"
- Degree of Protection : IP 58
- Minimum Cooling Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : Star Delta (SD)
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

The V8 DRS Solar Pumping System is a configurable solar-powered water-lifting solution designed for agricultural irrigation, livestock watering, and remote water-supply applications. It is intended to support efficient water delivery from suitable water sources while reducing dependence on conventional electricity. Depending on the selected configuration, the system may incorporate a surface or submersible pump, solar-compatible motor, and dedicated controller. Its practical arrangement supports installation flexibility, routine maintenance, and reliable daytime operation. Available with different motor powers, flow capacities, pumping heads, and electrical configurations, the V8 DRS series can be supplied to meet specific project requirements for farms, gardens, reservoirs, and rural infrastructure.

Key Specifications
Specification Details
Product Type V8 DRS Solar Pumping System
Model / Series V8 DRS
Pump Design Surface or submersible pump, depending on model
Power Source Solar photovoltaic power system
Motor Type Solar-compatible electric motor
Pump Material Stainless steel, cast iron, or engineering-grade materials, depending on model
Color Metallic, blue, or manufacturer-specific finish
Construction Compact, solar-compatible pumping assembly
Motor Power Available in different HP / kW configurations
Voltage Available in different AC or DC configurations, depending on model
Frequency 50 Hz or as specified for the selected configuration
Flow Capacity Available in different discharge options
Pumping Head Available in different head configurations
Solar Panel Capacity Selected according to pump power and operating requirements

Salient Features
Highly efficient 3-Phase Water Filled Motor
- 100% EC grade copper winding
- Easily Rewindable
- Motor Designed with Higher Cooling Effect Ensures Longer Life
- Sustainable uniform performance for years
- Ensures long life durability
- Optimized Hydraulic & Mechanical Design
- Improved efficient performance
- Excellent output in Low Radiation
- Dynamically balanced design
- Zero maintenance

Product Specification
Power Range : 3.0 HP to 10.0 HP
Operating Speed : 0 - 2890 RPM
Operating Frequency : 0 - 50 Hz
Input Solar DC Power Range : 3000 Wp, 10000 Wp
Input Solar DC Voltage Range : 330 Vmp , 600 Vmp
Head Range : 10 Mtr , 50 Mtr
Discharge Range : 126000 LPD , 425000 LPD
Type of Duty : S1

Material Of Construction
Part Grade
Oil Seal : Nitrile butyl rubber
Motor Shaft : SS - 420
Motor Body : Cast Iron / J4
Motor Bush : LTB-4 / Teflon
Thrust bearing assembly : SS - 420 & Carbon
Base : Cast Iron
Bracket : Cast Iron
Flange : Cast Iron
Casing : Cast Iron
Impeller : Cast Iron

The V8V9 MRS Solar Pumping System is a configurable water-lifting solution designed for agricultural irrigation, livestock watering, and remote water-supply applications. The V8V9 MRS designation can be used for a model series covering different pumping capacities and configurations. Depending on the selected version, the system may incorporate a surface or submersible pump, solar-compatible motor, and dedicated controller. Its modular arrangement supports efficient water delivery, convenient installation, and flexible project sizing. Suitable for farms, gardens, reservoirs, and rural infrastructure, it can be supplied with different motor powers, flow rates, pumping heads, and electrical configurations to meet buyer-specific requirements.

Key Specifications
Specification Details
Product Type V8V9 MRS Solar Pumping System
Model / Series V8V9 MRS
Pump Design Surface or submersible pump, depending on model
Power Source Solar photovoltaic power system
Motor Type Solar-compatible electric motor
Pump Material Stainless steel, cast iron, or engineering-grade materials, depending on model
Color Metallic, blue, or manufacturer-specific finish
Construction Compact, solar-compatible pumping assembly
Motor Power Available in different HP / kW configurations
Voltage Available in different AC or DC configurations, depending on model
Frequency 50 Hz or as specified for the selected configuration
Flow Capacity Available in different discharge options
Pumping Head Available in different head configurations
Solar Panel Capacity Selected according to pump power and operating requirements

Product Specification
Power Range : 1.0 HP to 2.0 HP
Operating Speed : 0 - 3100 RPM
DC Power Range : 900 Wp - 2000 Wp
DC Voltage Range : 70 Vmp - 110 Vmp
Head Range : 30 Mtr - 90 Mtr
Discharge Range : 8000 LPD - 30000 LPD
Type of Duty : S1

- Zero Running Cost
- Less Maintenance
- Eco-Friendly
- Simple Installation
- Pollution Free

Material Of Construction - Motor
Part Grade
Mechanical Seal : Graphite Ceramic
Motor Shaft : Stainless Steel
Motor Body Pipe : SS-304
Lower Hosing : Aluminum
Diaphragm : High Nitrile butyl rubber
Top Cap : Stainless Steel
Bottom Plate : Stainless Steel
End Cap : Stainless Steel

MATERIAL OF CONSTRUCTION SCREW (HELICAL) PUMP
Part Grade
Outlet : SS-304
Suction : SS-304
Outer Shell : SS-304
Rotor Screw : Stainless Steel
Stator : Rubber Coated Alloy
Material Of Construction Centrifugal Pump
Part Grade
Check valve housing : SS-304
Check valve : PC
Suction : SS-304
Outer Shell : SS-304
Impeller : POM
Bowl : PC
Pump Bush : NBR
Pump Sleeve : Stainless Steel
Pump Shaft : Stainless Steel
Coupling / Pump Couple : Stainless Steel

The AC Solar Pumping System - Surface Pump is a reliable solar-powered water-lifting solution designed for irrigation, agricultural water transfer, and other clean-water applications. It combines a surface-mounted AC pump with a solar-compatible power system to deliver dependable water flow without requiring continuous grid electricity. The system is suitable for farms, gardens, livestock facilities, and remote water-supply projects where access to conventional power may be limited. Its practical design supports easy installation, routine maintenance, and flexible system configuration. Available with different pump capacities, solar power requirements, and control options, it offers an efficient solution for reducing operating costs and improving water availability.

Key Specifications
Specification Details
Product Type AC Solar Pumping System - Surface Pump
Pump Design Surface-mounted centrifugal pump
Power Source Solar photovoltaic power system
Motor Type AC electric motor
Pump Material Cast iron, stainless steel, or engineering-grade materials, depending on model
Color Metallic, blue, or manufacturer-specific finish
Construction Compact, surface-mounted pump assembly
Motor Power Available in different HP / kW configurations
Voltage Single-phase or three-phase AC, depending on model
Frequency 50 Hz or as specified by buyer
Flow Capacity Available in different discharge options
Pumping Head Available in different head configurations
Solar Panel Capacity Selected according to pump power and operating requirements
Controller Solar pump controller / inverter-compatible system

V5 Borewell Submersible Pumpset
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are
assembled under pressure and rigidly locked in stainless steel stators shell.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles.

Salient Features
- SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series)
- 9 Mtr. Head Per Stage In Radial Flow Series.
- Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads.
- Dynamically balanced roating parts ensure minimum vibration and longer life
- Motor Portion covered with corrosion resistant S.S. J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS pumps are available in (GRS - Series)

Specification
- Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply
(Single Phase available in 3 HP to 5 HP)
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 640 Mtr.
- Discharge Range : 690 LPM to 80 LPM
- Outlet Size in Inch : 1.5 , 2.0" & 2.5"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2
kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star
Delta (SD) upto 9.3 kW
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure.

Pump Liquids
- Clean
- Thin
- Non-Aggressive
- Non-Explosive
- Clear
- Cold
- Fresh water
- Without abrasives
- Solid particles

Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series
- 60 feet head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads.
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Additional intermediate bearing in higher stage pumps
- Fully SS pump set are available in SS - 304 Grade

Specification
- Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V,
50Hz AC Supply.
- Speed : 2900 RPM
- Head Range : 12 Mtr. To 600 Mtr.
- Discharge Range : 1080 LPM to 170 LPM
- Outlet Size in Inch : 2.0, 2.5 , & 3.0
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct
Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW
- Maximum Starts Per Hour : 20 Times

Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5

V8 URC

V6 STD. FMC

V6 STD NRS

V6 Fully SS

V6 FMC

V6 3PCS. URC

V5

V5 GRS

V5 FMQ

V4 UT

V4 Slim Submersible Pumpset