For different industrial applications. Ranging from 0 to 500 volts dc output And 25000 amps. Capacity - suitable for Both h.T. & l.T. Input supply. - electroplating / anodizing - hydrogenation - dc. Drive and other electrochemical processes Depends upon capaicty
We can supply Distribution transformer from the range 10 Kva to 3000kva 33 kv class and power Transformer from 1000 kva to 5000kva 33 kv Class Depend supon capacity
10 kva to 3000 kva capacity, 3 - phase, 50 hz. For different industrial applications. Input voltage range : 300 to 500 volts or as per Customers requirement Output voltage : 380/ 400/415 + 1% Depen upon caapcity
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Characteristics: Rated voltage: 3.2 V Working voltage: 3.0-3.3V Minimum discharge voltage: 2.0-2.8 V Maximum charging voltage: 3.60-3.65 V Volume energy density: 325 Wh/L Weight energy density:>90 Wh/kg Specific power: 200 W/kg Time durability:>10 years Cycle durability: 2750-12000 cycles Advantages: Higher safety Better service life and cycle life Environmental protection Fast charging Wide working temperature range Low energy density Application: Energy storage equipment Electric tools Light electric vehicles Small electrical appliances Start the power and move power supply
VRLA batteries are including three main types Absorbed Glass Mat AGM and Gel batteries and Tubular battery They are frequently utilized in uninterruptible power supply UPS systems emergency lighting installations and telecommunication equipment where continuous and hasslefree functionality is imperative Additionally VRLA batteries find extensive application in electric vehicles renewable energy systems and other contexts that necessitate a reliable and secure energy storage solution Advantages MaintenanceFree Operation Sealed Construction Enhanced Safety Versatile Applications Long Service Life Improved Efficiency Environmental Friendliness Higher Voltage Output Faster Recharge Rates Slower Discharge Rates Higher Capacity Range Economical
Characteristics Rated Voltage:1.2V Charging Voltage:1.4-1.45V Termination Voltage:0.9-1.0V Energy/weight:60-120 Wh/kg Energy/Volume140-300 Wh/L Power/Weight:250-1000 W/kg Selfdischarge Rate: Generally 20-30% per month Charging and Discharging efficiency:66% Number of Charging and Discharging cycles: 500-5000 Times Advantages:High Energy Density, Efficient at Highrate Discharges, Long Cycle Lif,e Wide Temperature Usage Range, Stable Electrochemical Characteristics, Pollutionfree Green Battery, No Memory, Effect Lower Costs, Good Safety Performance. Applications:Solar Lighting Emergency, Lighting Hightemperature Lamps, Car mounted TBOX, Car OBD, ECALL system Electric Tools, Medical Equipment, Vacuum Cleaner Shaver, Electric Toothbrush, Electric Toy Battery, Game Console Handle.