The CORI is the product for the direct reduction unit:
First, it will be stored in product passivation silos, its transportation by conveyors. After that, it will be stored in the warehouse for further use.
Production rate fo312 T/H. Assuming 8,000 hours of annual
operation, this equates to in annual production of 2,500,000 tonnes.
-IRON: (Rod a Benton):Hot-rolled product in multipurpose steel for high-adherence construction, weldable in RB 500 grade. NA 8634(2015) and ISO 6935-2 (2015). Diameter:
A wide range of diameters: 8,10,12, 14, 16,20,25,32,40 mm.
Length :12m (-0mm +100mm) with the possibility of making specific lengths of less than 12m according to customer demand for diameters ranging from 8mm to 16mm.
12m to 18m for diameters ranging from 16mm to 40mm.
Marking :
A specific AQS marking is engraved on the rebar bars for the diameters: 8,10,12,14,16mm And the identifying code AQS-diameter-RB500 for the diameters: 16,20,25,32,40mm
- Portland Cement 42.5 (Bags, Bulk)
-Wire rod: of round section with a diameter varying between 5.5 mm to 14 mm, of high quality.
The round and smooth wire rod is obtained by hot rolling in accordance with the Algerian standard an 8634 and according to international standards.-The Fields Of Use Of Wire Rod Are As Follows:- Drawn Wire-Welded Mesh-Nail, Tie Wire, Galvanized Wire- Gabions- Barbed Wire-Spring Wire- Bolt-Nut-Screw- Paperclips-Pickup Wire-Welding Wire
-BILLET: A billet is a section of metal used to roll into bars and shapes. It can be produced with ingots or directly by continuous casting. Billets are used as raw materials or for extrusion, forging, rolling and other metal processing operations.
Rockwool, also known as mineral wool, is an insulation material made from natural stone or mineral fibers. The density of Rockwool refers to the mass of the material per unit volume, and it is commonly expressed in kilograms per cubic meter (kg/m�³) or pounds per cubic foot (lb/ft�³).
The density of Rockwool can vary depending on the specific product and its intended application. Common densities for Rockwool insulation products range from approximately 40 kg/m�³ (2.5 lb/ft�³) to 200 kg/m�³ (12.5 lb/ft�³) or more. The choice of density often depends on factors such as thermal performance requirements, structural support needs, and the specific application of the insulation.
* PURPOSE
customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system.
BACKGROUND
* Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles.
* GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates.
Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion
* Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected.
APPLICATION
Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
