Shenzhen Anyk Technology Co., Ltd.

Industrial 10/100BaseTX to 100BaseFX Media Converter is a costeffective solution for the converting 10/100Base-TX (Auto MDI/MDIX) to 100Base-FX cabling. It provides the two power inputs that can be connected simultaneously to the DC power sources. If one power input fails, the other one acts as a backup.Industrial 10/100BaseTX to 100BaseFX Media Converter also provides relay alarm outputs to warn when the port link failure, so the technician can respond quickly with appropriate emergency operation procedures.Also, there are DIP- switches to set the operation mode for relay alarm,Fiber ports, link loss forwarding function, and UTP operation mode.

Features
UTP to Fiber Media converter
Auto Negotiation Speed and Half/Full Duplex
Support 12 to 48VDC power inputs
TX port support Auto MDI/MDI-X
Relay alarm output for port link failure
IEEE 802.3x flow control support
Flow control on full-duplex
Back pressure on half-duplex
Built-in Link Lose Forwarding Technology
DIN-Rail or wall mountable
DIP-switches to set the operation mode and Link- Lost-Forwarding function.
Redundant dual DC power Inputs

Physical Dimension
Industrial 10/100BaseTX to 100BaseFX Media Converter dimension (W x H x D) is 54mm x 135mm x 105mm

10/100/1000m fiber media converters

Main features

Auto negotiation function allows utp ports to auto select 10/100/1000m and full duplex or half duplex.
The utp port supports the connection of mdi/mdi-x auto crossover.
Multimode fiber: the max distance up to 224m/ 550m
Singlemode fiber: the max distance up to 100km
Supporting the max 1536 byte ethernet packet
Supporting flow control
Adopting internal power supply

Technical specifications

Operating standards: ieee802.3z/ab, 1000base-t and 1000base-sx/lx
Mac address table: 4k
Data buffer: 256k
Connector: utp: rj-45, 10/100/1000mbps; fiber: sc, 1000mbps
Cable :
Utp cable: cat 5e or cat 6 (the max distance up to 100m)
Fiber : multimode : 50/125, 62.5/125ª8m (the max distance up to 550/224m)
Singlemode : 8.3/125, 8.7/125, 9/125ª8m (the max distance up to 100km)
Flow control
Full duplex: ieee802.3x
Half duplex: back pressure.
Power: ac 220v(170-260v) 50hz; dc 5v¼2a
Ambient temperature¦0 ½ +50µ
Storage temperature¦-20 ½ +70µ
Humidity¦5% ½ 90%
Dimensions ¦40 (high) x 110 (width) x 140 (length) mm

DaShi ANYK-R17 Rack System is a configurable media converter rack that can host 16 slots of media converters and 1 slot net manage card.A wide range of media converters is available depending on your variety of network cabling environment. These optional media converters include UTP to multimode or single mode fiber cable. The Chassis provides a central power supply to the converters and serves as a converter center and wiring concentrator.
1. Hot Swappable
The design of the power system is based on an idea of providing maximum flexibility and redundancy. In this way, you may remove any of the two power supplies without turning off the system.
2. Redundancy
During operation, both power supplies are switched on and share the current load. In case that one of them should fail, the other will instantaneously take 100% of the load without any loss. Similarly, if one power supply is removed from servicing, it can be switched off and removed while the chassis continues 3.functioning.
3. Protection System
The power of each converter bay comes from the two shared power supplies. Each bay is isolated from each other under a certain protection mechanism, so that it is free from any problem that might occur to the power supplies or faulty converter bay. This is the best solution to protect your investment in media converters.
4. Media Converters
The functions of all 16 slots in ANYK-OaxxH-x-1-1M are identical. 2U Media Converter Moule series can work independently and be installed into any available slot of ANYK-OAxxH-x-1-1M;
Parameter:
shape size: 426mm*278mm*88mm* (internal power supply )
weight: 5KG
power source: 100v-275VAC, 50-60Hz ,100A
Operation Temperature:0ípC-60ípC
Humidity:5%-95%
Storage Temperature:-10ípC-70ípC
Application: WAN and LAN system( FTTB,FTTH ) ISP suppliers

ANYK Series 10/100M Singlemode Single Fiber Converter is the conversion equipment of Ethernet optical-electronic signals between 10/100M UTP interface (TX) and 100M Fiber interface (FX). The traditional 10/100M Fast Ethernet can be extended to the distance of 90km through Single Optical Fiber link. The performance and quality of the products are excellent because of adopting latest IC from Taiwan. It must be used in couples,because the transmitted optical differs from the receive optical in wavelength. 6 Group LED indicated lights could fully monitor the working conditions of Converters. It is easy for end-users to observe the conditions of network. The Series product with reasonable price is especially designed for network end-users.
Main features

Auto negotiation function allows UTP port to auto select 10M or 100M, and Full Duplex or Half Duplex;
UTP port supports MDI/MDI-X auto crossover;
Support link fault pass through function(LFP),with indicator function of link fault: When optical fiber or UTP is at fault, the converter could stop all the link;
Support far end fault function;
Multiple Optical Transceiver could be chosen: SC, ST or FC, singlemode / multimode;
Supporting 1600 bytes packet for management;
Converter working mode could be chosen: Store and forward switch mode, Modified cut-through switch mode, or Converter mode;
Internal Circuit of prevented thunder could greatly reduce damage of the converter caused by thunderbolt induction;
Internal or External switching power: for users to choose.
Technical Specifications
Operating standard: IEEE802.3u, 10/100Base-TX and 100Base-FX
Built in 128Kb RAM for data buffer;
Connector: UTP: RJ-45,10/100Mbps; Fiber: SC,100Mbps
Cable:
UTP: Cat. 5 UTP (the max distance up to100m)
Fiber ( Singlemode): 8.3/125, 8.7/125, 9/125, 10/125ª¦m(the max distance up to 90km)
Flow control
Full Duplex:IEEE802.3x
Half Duplex:back pressure
LED: Power, FX Link/Act, FX SD(Signal Detect), TX 100, TX Link/Act, TX FDX.
Power : AC 220V(170-250V),50Hz; DC: 5V,1A
Ambient temperature:0 - +50íµ
Storage temperature:-20 - +70íµ
Humidity:5% - 90%
Dimensions:
Power external: 26 (high) x 70 (width) x 94 (length) mm
Power internal type: 30 (high) x 110 (width) x 140 (length) mm

14 slots media converters

Ain features
The power of the rack can be supplied by the type of single power or dual power. Adopting dual power supply, the load of each power can be reduced and the life of the power would extend. When one power supply is at fault, the other one can still work independently. It would enhance the reliability of the rack.
Supplying the converters or powers to be plugged and played.
It is possessed of stable performance, large capacity of power supply, and ease for management and maintenance
2u high: 19-inch standard design

Technical specifications

Capacity : 14 slots available
Power: input: ac 100 ½ 260v, 50½60hz
Output: dc +5v 12a
Power protection: protection from over voltage, over current and short circuit
Working temperature¦0½50µ
Storage temperature¦-20µ½70µ
Relative humidity¦5%½95%
Dimensions: 485 (wide) ß 245 (length) ß 90 (high) mm

ANYK series Fiber Media Converters can convert Optical-Electric Ethernet signals between 10/100M UTP interface (TX) and 100M optical fiber interface (FX). It can extend traditional 10/100M fast Ethernet to the distance of 120km through optical fiber link. It possesses stable performance and good quality by adopting latest IC packages from USA and Taiwan. 6 Group LED indicated lights could fully monitor the working conditions of Converters. It is easy for end-users to observe network operation. ANYK series external power supply Converters could be used alone, or inserted to 14 slots Converters Rack supplied by DaShi Corp. suitable for the use of Network Centre.

Main features
Auto negotiation function allows UTP port to auto select 10M or 100M, and Full Duplex or Half Duplex;
UTP port supports MDI/MDI-X auto crossover;
Support link fault pass through function(LFP),with indicator function of link fault: When optical fiber or UTP is at fault, the converter could stop all the link;
Support far end fault function;
Multiple Optical Transceiver could be chosen: SC, ST or FC, singlemode / multimode;
Supporting 1600 bytes packet for management;
Converter working mode could be chosen: Store and forward switch mode, Modified cut-through switch mode, or Converter mode;
Internal Circuit of prevented thunder could greatly reduce damage of the converter caused by thunderbolt induction;
Internal or External switching power: for users to choose.

Technical Specifications

Operating standards:IEEE802.3u,10/100Base-TX and 100Base-FX;
Data buffer: Built-in 128Kbyte RAM.
Connectors: UTP Connector: RJ-45, 10/100Mbps; Fiber Connector: ST/SC/FC, 100Mbps
Cable:
UTP: Cat. 5 (the max distance up to 100m)
Fiber ( Multimode): 50/125, 62.5/125ª¦m(the max distance up to 2km or 5km)
Fiber ( Singlemode): 8.3/125, 8.7/125, 9/125, 10/125ª¦m(the max distance up to 20 - 120km)
Flow Control
Full Duplex: Supporting standard IEEE802.3x
Half Duplex: back pressure
LED: Power, FX Link/Act, FX SD(Signal Detect), TX 100, TX Link/Act, TX FDX,.
Power Requirement: AC 170 - 240V, DC 5V.
Ambient Temperature: 0 - 50íµ
Storage Temperature: - 40 - 70 íµ
Humidity: 5 - 90%
Dimensions: Internal power: 30í-110í-140mm
External power: 26í-70í-94mm

4 high-powered RJ-45í»s port of 10/100Mbps self-adaptive (Auto MDI/MDIX)
1 100M(single-mode/multi-mode)optic port
Providing table top and frame type install
Support VLAN and Trunking
Buffering:1M
Address table filtrate:1K

Follow the fast Ethernet standard of IEEE802.3 10BASE-Tí»s Ethernet and IEEE802.3u 100BASE-TX
Support all protocol in public, eg: TCP/IP, IPX, XNS, Appletalk, Vines, DECnet, ARP, DECLAT and Lansoft etc.
4 10/100Mbps self-adaptive ports (Auto MDI/MDIX)
1 100M(single-mode/multi-mode)optic port
The self-diagnostic function can obviate network mal-function
Providing table top and frame type install
High speed cascade connection port used to link higher layer Switch or other device
The dynamic buffering equipped by equalizing network load and to prevent the f blockage from losing
All ports possess self-adaptive and full /half-duplex ability
The face plate indicator lights keep watch on the work state, hence overall SmartWatch function can simplified the solving of malfunction
Choose fast storage, transmit and directness transmit mode automatically in order to reduce the delay
Provide the maximum bandwidth to 1Gbps, 100% transmit data rate
Filter broadcasting storm
Line speed is filtrate / transmit
Support VLAN and Trunking
The dynamic bandwidth equipoise
Automatic MAC address learning function
The entire compatibility standard of Ethernet application
Specification:
Network standard:
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
Network protocol:CSMA/CD
Data transmit speed:
Ethernet: 10Mbps(half-duplex) 20Mbps(full duplex)
Fast Ethernet: 100Mbps(half-duplex)200Mbps(full duplex)
Topology:Star
Line type:
10BASE-T: unshielded twist pair (UTP) 3,4,5 (max length:100 m)
EIA/TIA-568 100 ohm screens twisted pair (STP) (max length:100 m)
100BASE-TX:Not screen the twisted pair (UTP) 5 (max length:100 m)
100BASE-FX:Single-mode/Multi-mode fiber(max length:80m)
Port:4 10/100Mbps auto-negotiate ports plus 1 100M fiber port(choice Single-mode/Multi-mode )
Physical and the environmental
specification:
Input voltage:5V DCIA outside general power
Power consumption:5W
The work temperature:0-50íµ
The storage temperature:-25-+55íµ
Environment humidity:5 % - 90% non-condensing
Size:171mm x 98 mm x 27.8mm
Table mini type
Performance index:
Swap mode:storage transmit and end to end
Buffering:1M
Address table filtrate:1K
Transmit/-filtered rate:line speed, 148,800 bps ( 100Mbps ) per port
MAC address table:Self-study, self-refresh
MAC address aging time:10-1000000 seconds (default 300)

Anyk-s4008 8 ports fast ethernet switch

8-port 10/100Mbps-TX or 100Base-FX auto-negotiating Switch
Provide Dedicated Bandwidth in Half or Full-Duplex Modes.
Support port-based Virtual LANs (VLANs).
2.0 Gbps aggregate bandwidth with speeds of up to 200Mbps per port.

Description:
The ANYK-S4008 Fast Ethernet Switch provides the power of switching with the ease of use and affordability of traditional shared hubs. Truly Plug-and-Play, the ANYK-S4008 Fast Ethernet Switch automatically learns about the devices on your network and configures itself, without complicated setup procedures. Dramatic improvements in performance can easily be seen, with speeds of up to 200Mbps per port. Since full bandwidth capability is achieved on each individual port, the congestion problems of shared hubs are easily avoided.
Employing a Buffered Store-and-Forward transmission method with Back Pressure and Flow Control ensures maximum reliability. For added sturdiness, these switches are housed in steel casings and can be rack mounted using the included Rackmount kit. ANYK-S4008 Fast Ethernet Switch comes with 8-switched RJ45 or fiber optical ports. Powerful enough to run your networkí»s backbone, yet so easy they can be used in place of your desktop hubs, let DaShi Crop. and the versatile ANYK-S4008 Fast Ethernet Switch bring the power of switching to you.

Features:
Ideal for Integrating the 10/100Mbps or 100BaseFX Ports. Provide Dedicated Bandwidth in Half or Full-Duplex Modes
NWAY Technology Detects Cabling Type, Speed, and Duplex mode
Transparent transfer all protocols such as TCP/IP, IPX, XNS, Appletalk, Vines, DECnet, ARP, DECLAT and Lansoft etc.
Compatible with All Major Network Operating Systems
Advanced Store-and-Forward Packet Switching Optimizes Data Transfers
Full wire-speed layer 2 switch on all ports
Support port-based VLANs
1M Buffer Memory
Internal 1k MAC address table
- Auto address learning
- Auto address aging (default 300 Seconds)
Supports both Full/Half duplex ports
Flow control capabilities
Automatic Transmit delay control capabilities and maximum delay guarantee
Broadcast flood filtering
Filtering/Forwarding/Learning Rates
2.0 Gbps aggregate bandwidth with speeds of up to 200Mbps per port
Support Comprehensive At-a-Glance LEDí»s
Specification:
Standard
IEEE 802.3 10BASE-T
IEEE 802.3U 100BASE-TX, 100BASE-FX
IEEE 802.1Q VLAN
IEEE 802.1p Priority Queue
IEEE 802.1x
System:
Power Supply:90 / 220 V
Power Consumption:< 30 Watts
Dimension:440mm x 220mm x 44.4mm
1U rack-mount
Temperature:0 to 50C
Humidity:5% to 95% non-condensing
Storage Temp.:-25 to +55 C

Media converter

Parameter
Specifications
Access mode
10/100mbps
Standard
Ieee802.3 10base-t ethernet, ieee802.3u, 100base-tx/fx fast ethernet, ieee802.3x flow control, ieee802.1q vlan, ieee802.1p qos, ieee802.1d spanning tree
Wavelength
850nm/1310nm/1550nm
Transmission distance
Single-fiber single-mode: 25/40/60/80/100km ; category-5 twisted pair: 100m
Port
One rj45 connector, connected to stp/utp category-5 twisted pair one fiber port: multi-mode - sc or st (fiber size: 50, 62.5/125µm) single mode - sc/fc fiber port (fiber size: 9/125µm) single-fiber single-mode - sc/fc fiber port (fiber size: 9/125µm)

Conversion mode


Medium conversion, storing and forwarding

Mac address table


I k

Buffer space


1mbit

Flow control


Full duplex state: flow control; half duplex state: back pressure mode

Delay


9.6us

Bit error rate


<1/1000000000

Mtbf


100, 000 hours

Led


Power tx link ( fiber link action ), tp link1000, tp link100, tp act ) fdx (fx full duplex mode), fx100 (fiber, with a transmission rate of 100m) tp1/2/3/4 link/act (1/2/3/4-port twisted pairs connection action) tp1/2/3/4100 (1/2/3/4-port twisted pairs, with a transmission rate of 100m)

Power


Ac220 0.5a/pc-48(builtin)

Power consumption


5w

Operating temperature


-10~55ºc

Operating humidity


5%~90%

Storage temperature


-40~70ºc

Storage humidity


5%~90% (non-condensing)



Dimensions


140mm * 111 * 30mm(in) 95 x 70 x 26mm(out)