Product Introduction SANDI AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-750VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface (Optional)
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc (�±10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80�°C. When the DC panel has a temperature over 100�°C, the module will stop working; when the DC panel has a temperature below 90�°C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Supplier: Led bulb, tube light, panel light, decoration light, wall light, steel wires, steel plate, stainless steel plate, twisted wire rods, galvanized wires, wire mesh, site fencing, mosquito mesh, thread rods, rebar, twisted rods, t bar, nuts and bolts, hardware, pvc pipes, upvc pipes, api pipes, melamine, mdf board, plywood, film faced, shuttering, packing, core veneer, face veneer, hdf molded door skin, door filler, tubular particle boards, pvc boards, wpc boards, doors, block board, hard board, gypsum board, canopy, carpet, flooring wooden, bamboo, laminated engineering, tiles, granite tiles, granite blocks, black galaxy, wash basin, water closets, washbasins, ss sinks, faucets, furniture, pvc edge bending, crew, locks, pvc seals, silicone cartridges, shower enclosures, shower door hinges, handles, knobs, brackets, slides, nails, solar panels, flexible solar panels, solar power station, battery, inverters, rechargeable fans, lights, spring, 3ply disposable face mask, oxygen concentrator ,
Services: Buying office, oem, components sourcing, value added services
Buyer: In shell pecan nut, macadamia nut
SANDI SERIES charging module is for electric vehicle charging station. With single-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. Functional details 1. Hot plug Plug technology is applied to the charging module to provide convenience for installation and maintenance. The access of the charging module to the system shall not disturb the output voltage of the system. 2. Advanced current sharing technology Under constant voltage working mode, the charging modules can share current automatically within 10S, with degree of unbalance less than �±0.5A. 3. Control of input limited power Refer to Fig. 1-10 for the relation between the output power and input voltage of the charging module. When the input voltage is within 360 Vac ~ 450 Vac (return difference is less than 5V), the module can output the maximum power of 20 KW; when the input voltage is within 260 Vac ~ 320 Vac, the module can still work normally under limited power mode. 4. Control of output constant power When there is a rated input voltage, the output power of the module is 20 KW. Refer to Fig. 11 for the relation between the output voltage and the output current of the module. The SD75050 module uses two operating modes with output voltage ranges of 50 to 750V. The module only selects the operating mode based on the value of the received demand voltage, and does not select the operating mode based on the actual output voltage. 5. Temperature limited power 6. Regulation of output current limiting point 8. Regulation of output voltage The output voltage of the module can be regulated constantly through the external monitoring module, with regulation range of 50Vdc ~ 750Vdc and minimum regulation step of 0.1 Vdc. 9. Fan control The built-in processor of the module can regulate the speed of the fan according to the internal temperature and output current of the module. 10. Protection of input overvoltage/ voltage shortage 11. Output overvoltage protection The overvoltage protection point is 260Vdc ~770Vdc ( +10 Vdc). Default is 778Vdc.The module can be started after manual intervention upon overvoltage protection. 12. Over-temperature protection The environmental over-temperature protection point is 80 C. When the DC panel has a temperature over 100 C, the module will stop working; when the DC panel has a temperature below 90 C, the module will automatically work again. 13. Protection of internal bus fault When the internal bus voltage of the module is beyond the overvoltage/ voltage shortage protection point, the module will be powered off automatically. At this time, there is no output from the module and the fault indicator light is on. 14. Short circuit protection In case of short circuit of the module, it will be subjected to protective shutdown and the red indicator light of the panel is on, and this condition will be transmitted to the monitor of the "module fault".
Product Introduction SAND AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-1000VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface
Product Introduction SAND AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module. Unique function High efficiency over the full load range, full load efficiency greater than 95.5% Wide output voltage range, 100-1000VDC, suitable for a wide range of Lithium and lead acid battery 5-inch LCD touch screen, easy to operate Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate Main features Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc. Three phase active power factor correction technology, reduces the harmonic interference to the grid Dual DSP design, achieve the full digital control, less components means high reliability Wide input voltage range, allows operation in most poor grid conditions Soft start charging and soft shutdown minimize the impact on the battery. Input, output have protective circuit breaker switch Module adopts hot pluggable design, which is convenient for maintenance. CAN/RS485 interface
VRLA batteries are including three main types Absorbed Glass Mat AGM and Gel batteries and Tubular battery They are frequently utilized in uninterruptible power supply UPS systems emergency lighting installations and telecommunication equipment where continuous and hasslefree functionality is imperative Additionally VRLA batteries find extensive application in electric vehicles renewable energy systems and other contexts that necessitate a reliable and secure energy storage solution Advantages MaintenanceFree Operation Sealed Construction Enhanced Safety Versatile Applications Long Service Life Improved Efficiency Environmental Friendliness Higher Voltage Output Faster Recharge Rates Slower Discharge Rates Higher Capacity Range Economical
Characteristics: Rated voltage: 3.6/3.7/3.8/3.85 V Standard discharge continuous current: 0.2C Maximum continuous discharge current: 0.5C Working temperature: Charging: 0-45 Degree Discharge: -20~60 Degree Finished product internal resistance:
Characteristics: Rated voltage: 3.6/3.7/3.8/3.85 V Standard discharge continuous current: 0.2C Maximum continuous discharge current: 0.5C Working temperature: Charging: 0-45 Discharge: -20~60 Finished product internal resistance:
Characteristics Rated Voltage:1.2V Charging Voltage:1.4-1.45V Termination Voltage:0.9-1.0V Energy/weight:60-120 Wh/kg Energy/Volume140-300 Wh/L Power/Weight:250-1000 W/kg Selfdischarge Rate: Generally 20-30% per month Charging and Discharging efficiency:66% Number of Charging and Discharging cycles: 500-5000 Times Advantages:High Energy Density, Efficient at Highrate Discharges, Long Cycle Lif,e Wide Temperature Usage Range, Stable Electrochemical Characteristics, Pollutionfree Green Battery, No Memory, Effect Lower Costs, Good Safety Performance. Applications:Solar Lighting Emergency, Lighting Hightemperature Lamps, Car mounted TBOX, Car OBD, ECALL system Electric Tools, Medical Equipment, Vacuum Cleaner Shaver, Electric Toothbrush, Electric Toy Battery, Game Console Handle.
