Model Number:
Portable Air Conditioner ((WT-F26 gray)
Power Type: DC
Use: Room
Condition: New
After-sales Service Provided: None
Warranty:1 year
Type: PORTABLE
Certification:CB, ce
Cooling/Heating:Cooling Only
Application:Car, Commercial, Garage, Hotel, Household, Outdoor, RV
Power Source:Electric, usb
Remote Control: Yes
App-Controlled: Yes
* PURPOSE
customers using FBC boilers (Particularly underbed feed FBC boilers) for the protection of inbed coils against erosion potential by applying highly abrasive resistant refractory on inbed coils above fuel feed system.
BACKGROUND
* Two of such actions are providing special alloy studs on inbed coils and applying highly abrasive resistant refractory on the outer bottom loops of inbed Coils which are above the fuel feed nozzles.
* GANESHAS has taken number of approaches to identify the key factors affecting erosion rates with an objective to enhance the life of inbed tubes as well as implementing the corrective action to reduce the erosion rates.
Phosphate coatings are often used to protect steel parts against rusting and other types of corrosion
* Erosion of inbed coils in fluid bed combustor is unavoidable phenomenon however the rate of metal wastage and thus the life of tubes depends on various factors like ash & fuel properties, design of Combustor / feeding system, flue gas velocities operating conditions etc. It has been also observed that maximum erosion prone inbed coils are those which come above fuel feed nozzles and an area of approximately 1 to 1.5 mts around fuel feed systems are badly affected.
APPLICATION
Phoscast-90 XR can be applied by ramming with wooden mallet having adequately large head @" dia x 5" length x 10â?? Jong handle). The desired lining or repair thickness is built up in several courses while ramming the mass to uniform thickness. Phoscast refractory should never be trawled to obtain smooth surface; ramming only should finish surface. Any excess mass is to be sliced off with trowel edge and then finished by ramming again for bed coil. Tube application of AFBC boiler, the material pasty mass should be finger pressed into the studs of the tube with maximum force. Finish should be given by pressing the hand palm against material applied, using surgical type thin rubber hand gloves.
Features:
• 2 ~ 3 mm stainless steel hairline finish faceplate.
• Position indicator display for floor, up/down direction and overload message.
• Optional interphone button and emergency light.
• Safety buttons :
Alarm button
Door open button
Door close button
• Service buttons includes :
Stop switch (es)
Attendant switch (ats)
Fan switch
• Powder coated ms box.
• Display option :
Standard 7 segment
Dot matrix
We are a company in Shaanxi province provide all series elevator parts such as PCB, Comb plate, guide rail, guide shoe, buttom, swith, oil can, door vane, wheel etc for Fuji, Selcom, LG-OTIS, KONE, SCHINDLER, MITSUBISHI and other famous brand.
TECHNICAL SPECIFICATIONS
DC-PWM driver without limit switch
220 V AC supply voltage
24 V DC brushed motor
Double channel (A,B) 100 ppr encoder
Clear opening dimension (700mm~900mm)
The number of opening/closing cycles per year
600.000
Multiple electronic settings
Size, length and velocity parameters
Door power that can be adjusted separately on
opening and closing directions
Compatibility with variation of open/close
command signals (24 V DC-220 V AC)
Ability to operate with single (close) signal
Adjustment of short circuit types as NO/NC
Multiple mechanic adjustments
Practical assembly
Panel adjustment in 3 axes
Adjustability of clear opening
Places of use
Low traffic building and houses
TECHNICAL SPECIFICATIONS
CE locking system
Modular sales and assembly option
Compliant with EN 81-58
Central 2 Panel (uninsulated) E 120 EW 20
Telescopic 2 Panel (uninsulated) E 120 EW 20
Telescopic 2 Panel (insulated) E 120 EI 45 EW 60
Multiple mechanic adjustments
Panel adjustment in 3 axes
Lock position adjustment
Spring stiffness adjustment
Mechanism position adjustment
TECHNICAL SPECIFICATIONS
CE locking system
Modular sales and assembly option
Compliant with EN 81-58
Central 2 Panel (uninsulated) E 120 EW 20
Telescopic 2 Panel (uninsulated) E 120 EW 20
Telescopic 2 Panel (insulated) E 120 EI 45 EW 60
Multiple mechanic adjustments
Panel adjustment in 3 axes
Lock position adjustment
Spring stiffness adjustment
Mechanism position adjustment
