Used 2.5m (100”) wide 2.25m (88")trim paper machine by gorostidi and bruderhaus. Producing mg papers, completely overhauled in 2004. Producing 18 to 140 gsm basis weight grades at a maximum design spe
A very versatile Board Machine, operating width 4200 mm, maximum speed is 450 m/min, producing
fluting, liner, plasterboard liner, brown board and other grades. Grammage produced 110 to 600 gsm.
Commissioned in 1988, latest upgrades in 2000-s.
Installed production capacity is up to 450 t/day and the mill produced in excess of 110,000 t/year.
3 Stock Preparation Lines
Line 1 – bottom layer.
Horizontal pulper, 200 TPD, equipped with ragger, waste paper conveyor, two stock pumps with motors,
stock chest, two more stock pumps with motors, three HD cleaners, secondary sorting pulper (200TPD),
stock chest, two pumps, twin pressure screen (holes diameter 4 mm), rejects to chest, rejects pump, two
vibrating screens (holes 6 mm), stock chest, stock pump, deflaker, twin disc refiner, stock chest with
agitator, machine stock chest. All Polish and Russian built.
Line 2 – middle layer.
Horizontal pulper, 200 TPD, equipped with ragger, waste paper conveyor, two stock pumps with motors,
three HD cleaners, stock chest, two stock pumps, secondary sorting pulper (200TPD), stock chest, two
pumps, three twin pressure screens (holes diameter 2.6 mm), stock chest, stock pump, hot dispersion plant,
screw press, steam channel, disperger, thickener, stock chest, stock pump, 4 deflakers, 2 disc refiners, stock
chest with vertical agitator, stock pump, machine chest, two thickeners, disc filter. All Polish and Russian
built.
Line 3 – surface layer.
Horizontal pulper, 200 TPD, equipped with ragger, two stock pumps with motors, stock chest, 2 stock
pumps with motors, two HD cleaners, stock chest, two pumps, three disc refiners, stock pump, machine
chest.
All Polish and Russian built.
Pressure screens for formers
7 Tampella pressure screens complete with motors
Rejects screens 7 vibrating screens PS3100 (Finland)
Board machine
Seven Escher Wyss vacuum formers, stainless steel, 4-zones vacuum.
First press suction press with pneumatic loading.
Couch press.
Combi-press.
Second press.
Automatic felt feeding horizontal.
Automatic felt feeding vertical.
Tail feeding - air feed.
Rope feed system.
93 drying cylinders, 1500 mm diameter, face 4910 mm.
2 cooling cylinders, 1500 mm diameter, face 4910 mm.
Pocket ventilation system.
Size press: 1st roll diameter 800, face 4680 mm; 2nd roll diameter 800, face 4680 mm.
Reel-up.
NOTE: Some Drive Cabinets and Control Panels have been stripped of some components. Some power
supply components and cables are missing.
The mill stopped production in 2007.
Rewinder
Rewinder, 4500 mm, speed up to 1200 m/min.
*used voith paper machine. Manufactured 1965.
*hydraulic headbox type 2, installed in 1974 by voith. Slice: 3260mm. *wire width: 3450mm. Trim width: 3000mm.
*egoteur diameter: 400mm.
*dryness after couch roll approximately 28%.
*open draw to first press. First press: suction roll as under roll even blind drilled.
*dryness after first press approximately 40%.
*second press: solid reverse press. Dryness after second press approximately 46%.
*third press: solid press. Dryness approximately 50-52%.
*fourth press: offset press predryer ir on dryer 2 approximately 900 kw. Ahead of presnip is a steambox from vib.
*predryer section consists of (18) dryers. Diameter 1500mm x 3300mm. Pressure 3, 3 bar. Billblade coater with following air =-turn from spooner.
*coating quantity total up to 26g/m2.
*intermediate dryer section (7) dryers, diameter 155mm x 3300mm. *coating station for top and back built by kmw, rebuilt 1994 by btg to abc as run today with bentblade.
*included ir from solaronica/irt 450 and 500 kw.
*after dryers (17) pieces, the first (2) cylinders without steam with chromium-plated area, the rest diameter 1500mm x 3300mm. Pressure 2, 5 bar. Mat
*on line calender form kuster with (2) polymer covered rolls, (1) is an s-roll. Nip is soft-soft. The calender is from (70) ties. Automatic *tambour turning with pope from umv built 1996. Drive from stromberg. Each dryer has own ac motor. Design speed 500m/minute. Electrical, the machine can run faster, but depending on the open draw (no pick up) the speed is limited to 400m/minute. Grammage: double coated wood-free paper 100-300gsm.
Dekelon also provides paper machines for the production of specialty paper, included regenerated leather, asphalt paper, grey board, sealing gasket paper and filter paper. The specialty paper is made from the leftover material of various leather, scraps from the buffing machine, waste fibers and more, which are first processed into pulp and then formed into a paper sheet with a width of 0.6-5mm on the fourdrinier table. After this, the paper sheet undergoes dewatering, pressing, drying, polishing, flattening, cutting, winding and packaging in the specialty paper machine.
>applications
The specialty paper production line is widely used for different leather products, including leather bags, belts, clothes, sofas, shoes and more.
The ZGS series high consistency pulper is mainly used for pulp board and is primarily used for pulp board and waste paper disintegration, broke and waste paper deinking, and pulp purification. The capacity of this high consistency pulping system is 3-80t/d.
Under a high consistency, this pulper can achieve a rapid waste paper disintegration and deinking. Due to its large production capacity, low energy consumption, steam and chemical economy, easy maintenance, long service life, low noise, small vibration and stable operation, it saves up to 50% in water and energy.
this equipment is mainly used to degrade pulp board, waste paper and broken paper, deinking and pulp purification.
The xxzwn series disc thickener from dekelon, is used in the pulp and paper industry for dewatering and thickening low consistency paper pulp. Not only can this gravity thickener be used to thicken wood, cotton and straw pulp, it is also suitable for filtration and thickening applications in other industries.
When compared to other types of fiber suspension thickeners and other existing dewatering and thickening equipment, our disc thickeners feature a simple structure, easy installation and maintenance, a high production capacity, wide pulp adaptability and more. They have become increasingly popular among the pulp and paper industry.
According to the specific location of the drive part, the thickening machine has two arrangement modes. If the user is facing the outlet and sees the drum, and the drive part is on the right, the machine is a right hand thickener, represented by "y." on the flip side, if the drive part is located at the left, it is called a left hand thickener, represented by "z."
This wrapping/packaging paper machine is designed for both single and double layers. It comes in a variety of models, including the 1092 type, 1575 type, 1760 type, 1880 type, 2100 type, 2400 type, 2880 type, 3200 type,3600 type,4200 type and 4800 type. The number represents the machine deckle. It can also be equipped with a relevant device, according to paper grammage, machine speed, output, and other parameters.
The main equipment:
1. Pulp-flowing box: It adopts open-type pulp-flowing box, consisting of pyramid tube, staircase diffuser, distributing roller and box body. Staircase diffusion orifice plate pulp distributor is three-stage diffusion, which made of organic glass and upper and lower lip plates made of stainless steel. The upper lip plates can do full and local adjustment is three-stage diffusion.
2. Fourdrinier part: Wire table is 18000mm. Except draw-out seat made of alumina alloy, table rack is all welded by section steel with 1.5mm stainless steel cladding. Wire part is mainly composed of chest roller, forming board, wire-driving plate, water scrapping board, moisture absorbing box, and vacuum water-absorbing box, vacuum roller, wire-driving roller, electrical wire-tighter, pneumatic corrector, constant-tension wire-tighter, incision needle and margin raising device.
3. Press part: It adopts vacuum absorption injection paper, one streak of vacuum pressing and three streaks of pressing.
4. Drying part: It is set 28 pieces of f1500mm drying cylinders, including one f3000mm big cylinder of array type, 6+6+8+1+glueing machine+8 driven by enclosed gear box and lubricated by sparse oil.
5. Driving and control part: It adopts AC frequency conversion speed, drive step by step. Hard tooth surface gear box connected by universal coupling is used, and entire digital closed circle control system is used.
6. Press-polishing and paper reeling: It adopts super press polishing machine and level paper reeling machine.
