Find Verified Programming Cable For S7 200Plc And Tp170 Buyers, Importers and Buy Leads

Buyer is interested to receive quotations for the following RFQ -

Product Name: Instrument Multifunction Meters

Specifications:
Instrument Multifunction Meters Quantity Pieces:
150 pcs.

2
All instrument multifunction meters shall Measure the
following:
The current, the voltage, active power, reactive power, apparent
power, active energy, reactive energy, power factor and
frequency.
3
Accurate measured values with error limits:
Less than 0.5% for the Voltage (V) and the Current (I).
4
Good legibility with high-contrast:
At least 14 mm SCREEN or LED displays.
5 Electrically isolated current inputs.
6 Four quadrant operations.

7
Connection options:
- Single-phase.
- Or three-phase 3 and 4-wires.
- Suitable for balanced or unbalanced load.
8
Input voltage:
- Phase-to-phase Vp: up to 240 V.
- Programmable (primary and secondary).
9
Nominal input current:
1 A (primary should be programmable)
10 Dimensions:
At least (96 X 96 X ---) mm.
11 Auxiliary supply:
110 ± 10% V DC.
12 Multiple displays:
At least three lines.

13
Outputs:
- Four (4) Analog outputs for (MW, MVAR, V, A) shall be
choosable and programmable using the software tool .
- Each output can be programmed for any quantity.
Contact me/send me your offer via ramzi.v.saba@gmail.com

51

Schedule A - Continued

TECHNICAL PARTICULARS AND GUARANTEES

Item
No

Description

(DATA PARAMETERS REQUIREMENT)

Offered

14
Programmable inputs primary and secondary for C.T, V.T and
the Four required Analogue outputs programmable to any value
inside the required full range:
(-20 mA DC to +20 mA DC).
15 Response time: = 300 ms.
16
The continuous overload rating of the device shall:
1- Shall not be less than 1.3 times rated voltage.
2- Shall not be less than 2 times the rated current.
17
- Programming kit (configuration software + communication
cables) Via Rs 485 port or usb port.
- An additional USB programming port shall be applied.

18
The connection between the device and the RTU in the
substation is done through Modbus/TCP on Ethernet and
Modbus ASCII and Modbus RTU modes with the following
frame structure on RS-485 interface:
- ASCII framing (7-bit ASCII characters).
- RTU framing (8-bit characters)

19
The RS-485 serial communication must have a configurable
range of communication speeds:
- 4800 Bits/seconds .
- 9600 Bits/seconds .
- 19200 Bits/seconds.
With any of the following transmission settings for the RS-485
interface:
- even parity, 1 stop bit
- odd parity, 1 stop bit
- none parity, 1 stop bit
An additional USB programming port shall be applied.


Qty : 150 Set

Quantity Required : 150 Set/Sets

Shipping Terms : CIF

Destination Port : Jordan

Payment Terms : LC

Looking for suppliers from : Worldwide

Contact : Ramzi Saba

The buyer would like to receive quotations for -

Product Name: Calibration And Metering Equipment

Specifications:
1: Long range Indicator calibrator
Indicator calibrator optimar 25 with digital readout.
Application: for both analog dial indicator, dial comparator, level type test indicators & digital indicators.
Measuring range: 25mm
Resolution: 0,1um (0.0001mm)
Accuracy: 0+/- 0.2um
Power Supply: (220-240 VAC), 50Hz
Long clearly readable LCD monochrome digital display.
Selectable for either Metric or Inch
Output: USB interface for PC, RS232 Interface
Inspection Program: QN Software/dial – 32 with laptop and printer
Accessories: all operational accessories
Footswitch for data transfer supplied with calibration certificate issued by a laboratory accredited (including the calibration error and uncertainty)

List#4 Standard Glass Scale
High precision glass scale
Accuracy: 0.005mm
Line width: 0.005mm
Measuring range: (0-300mm)
Wooden Case
Calibration Certificate from national metrology institute (NMI)(VSL, PTB, NPL)

List#5 CERA Caliper Checker
Specification:
Wrung high-grade CERA gage blocks in a protective casting
Range: 0-600mm
Accuracy of block pitch: +/-0.005mm
Parallelism of block pitch: 0.005mm
Calibraton Certificate from accredited lab.

List #6 measuring tape and rule calibrator
Calibration unit for checking scales rule and measuring tapes with 0.001 mm resolution
Clamping range: upto 2000mm,
Drawer load range: 20n – 50N
Measurement uncertainty: ((0.05)^2 + (0.005L)^2)^0.5 where L: M
The instrument should be supplied with the required computer, software and accs.
Supplied with calibration certificate from national metrology institute (UME, vsl, or NPL)

List#8 Standard Thickness Foil
Standard block for calibration coating thkness gauge.
Range: (from 0.001 – 1)mm
Calibration certificate from accredited lab.

List #9 Precision Electronic Level
Wireless talyvel 6 electronic precession
Level flatness measurement with PC and Software
Measuring range: 1600s
Resolution: 0.1 arc-sec
Accuracy: +/-0.2sec
Power: 220VAC 50Hz
Calibration Certificate from national metrology institute NMI metrology

List# 10 Small angle Generator
Used for calibration of angle measurement device (sprit level, electronic levels and autocollimators)
with software and PC
Range 1m SAG
Uncertainty measurement = 1 arc second.
Power: 220 VAC 50Hz
Calibration Certificate from national metrology institute NMI metrology

List #11 Handheld, calibrator (process calibrator with portable pressure calibrator)
Measurement and electrical pressure generation at the touch of a button with integrated pump
From -0.8..+20bar (11.6..+290psi)
Accuracy: 0.025% of reading +/- 0.01% FS(including calibration certificate)
Generation/measurement of 4…20mA, 24V voltage supply to power transmitter
Pressure supply via external compressed air-line
With calibration certificate from national accredited lab.

List# 12 Process Calibrator
With Hydraulic handheld pressure with integrated medium reservoir & ergonomic handling
With hydraulic hand spindle pump with function for calibration & pressure switch test
Range: 0-1000 bar
Accuracy: 0.05% FS
Medium: non-corrosive gases, liquids, water
With complete 4 test and service cases
With refence pressure sensor (interchangeable without tools) 1.2m
With Calibration Certificate from national accredited lab

List #13 mechanical vacuum pump
Minus 1bar (220V 50Hz)
With Calibration Certificate from nationally accredited lab

List #14 High Performance Pressure Generation and Control 200MPa PPCH
Precision: to 0.003% of Q-RPT span.
Volume: 0-100cc, 50cc optimum, operated in larger volumes but pressure stabilizing time increases
Dynamic Mode typical time to ready
180sec into a 50cc volume & 20% FS excursions with default hold-limits 1.0 MPa (150psi) (lower in optimum conditions and with PG7302.
RS232 Cable, 9-in 2m for PPC3 COM1 or PPC3 to RPM4 connection

Quantity Required : MOQ

Shipping Terms : CIF

Destination Port : Jordan

Payment Terms :