Solar PV 1500VDC inline fuse connector 2-30A:
1.Current:2-30A;
2.Voltage:1500VDC;
3.IP68 as TUV approval;
4.Suitable for 10*85 inline fuse;
5.Easy to replace fuse;
6.Suitabe for cable at 2.5-10sqmm.
solar PV harness with inline fuse 1500VDC:
1.1500VDC;
2.With 2-30A inline fuse;
3.With 2.5-10sqmm cable;
4.Support 2in1,3in1,4in1,5in1,and 6in1 or more other solar cable enquiry.
Properties: The product is a white crystalline powder or a sandy-size granularity, and a pinkish crystalline powder or a sandy-size granularity as well. Sp.gr.2.953.01g/cm3, melting point about 1000centigrade, specific heat 1.056j/gcentigradeat 18100centigrade. Its slightly soluble in water, but insoluble in anhydrous hydrogen fluoride. The content of its crystal water will be decreased while the increasing of the molecular ratio, therefore its loss on ignition will be also decreased while the increasing of the molecular ratio. After the paste of synthetic cryolite with different molecular ratio dehydrates, the loss on ignition at 800centigrade will appear 10.34%, 6.22% and 2.56% when the molecular ratio reaches 1.74, 2.14 and 2.63 reactively.
Specifications:
Appearance white powder
F 52% min
Al 12% min
Na 33% max
SiO2 0.36% max
Fe2O3 0.08% max
CaO 0.5% max
P2O5 0.03% max
SO4 0.6% max
H2O 0.4% max
Loss on ignition 2 % max
Uses: Its mainly used as a flux in the aluminum smelting by fused-salt electrolysis; also an opalizer in the manufacture of enamel; an opacifier and auxiliary solvent of glass and enamel; an insecticide of crops; a flux in aluminum alloy casting; and in the production of ferrous alloy and effervescing steel; as well as a wear-resistant filler for resin and rubber-boned abrasive wheels.
Packing & Storage: In plastic coating woven bags with plastic film inside, 25kg,40kgs, 50kgs or 1000kgs net each, or as the requirement of clients.Stored: in a cool , ventilated, dry place.
Prperties: The prduct is a white needle crystal r pwder. SP. GR. 2.8823.13g/ cm3, sublimatin temp. 1272Celsiur scale.Its slightly sluble in water and greatly sluble in HF liquid. The chemical prperty fr the high density aluminum fluride is very steady, but that cntains certain crystal water will be decmpsed int Al23 at high temperature with HF being released.
Specificatin:
grade chemical cmpsitin % Physical character
F Al N2 Fe2342- P25 LI Bulk dity g/cm3
AF-0 61.0 31.5 0.30 0.10 0.06 0.10 0.03 0.5 1.5
AF-1 60.0 31.0 0.40 0.30 0.10 0.6 0.04 1.0 1.3
AF-2 58.0 29.0 2.8 0.30 0.12 1.0 0.04 5.5 0.7
AF-3 58.0 29.0 2.8 0.35 0.12 1.0 0.04 5.5 0.7
Uses: Its mainly used as an adjusting agent fr electrlyte in aluminum smelting by fused salt electrlysis, als in ceramic glaze, catalyst and flux f nnferrus metal metallurgy etc.
Brief Intrductin f the Prductin Technics
In the Hydrgen Fluride Reacting Furnace which is heated utside, Vitril reacts with Flurite t create the Hydrgen Fluride Gas and Anhydrus Fluride Plaster by heating in the prcess f prducing Aluminum Fluride, then the Hydrgen Fluride Gas react with dry Aluminium Hydrxide in Fluidized Bed t create t Aluminum Fluride and water.
Packaging
packed in wven PP bags with plastic film inside. Each bag has net weight f 25kgs, 50kgs, 500kgs and 1000kgs.
We can supply glass, ceramic, auto, slow-acting cartridge, and temperature limit fuses, fuse clips, fuse holders and blocks, fuse links, as well as other electronic products.
Our factory speclized in fuse and fuse holder for 40years in china.
In electronics and electrical engineering, a fuse (from the french fusée, italian fuso, "spindle" is a type of low resistance resistor that acts as a sacrificial device to provide overcurrent protection, of either the load or source circuit. Its essential component is a metal wire or strip that melts when too much current flows, which interrupts the circuit in which it is connected. Short circuit, overloading, mismatched loads or device failure are the prime reasons for excessive current.
Calcined Bauxite is obtained by calcining (heating) superior grade Bauxite at high temperature (from 850 oC to 1600 oC). This removes moisture thereby increasing the alumina content. Compared to an alumina content of about 57 % to 58 % in raw Bauxite, Calcined Bauxite has an alumina content of 82 % to 86 %. The heating is carried out in rotary kilns. Calcination is done at different temperatures ranging from 850 oC to 1600 oC depending upon the customer’s application.
We export Calcined Bauxite for various applications such as refractory bricks, abrasives, steel polishing, etc. We provide consistency in quality and availability of Calcined Bauxite at extremely competitive prices.
Applications of Calcined Bauxite:
Refractory Grade Calcined Bauxite (CB - I and CB - II Grade) : To make refractory grade, Bauxite is thermally treated at 1600 oC to produce Calcined Bauxite where the Alumina content is mostly above 82%.
Brown Fused Alumina, Proppants and Road Surfacing : To make the above grades, Bauxite is thermally treated at 1000 oC - 1200 oC to produce Calcined Bauxite where the Alumina content is anywhere between 80-88% depending on the requirement.
