NEOFLON PFA AP-210 is excellent in melt flowability and is suitable for injection molding and extrusion molding.
Introduction
- AP-210 is a copolymer of tetrafluoroethylene and perfluoroalkyl vinyl ether.
- Good melt flowability while maintaining excellent properties of PTFE. It can be melt-molded as a thermoplastic resin by injection molding and extrusion molding.
- Excellent chemical resistance which is not affected by most of the chemicals.
- Excellent heat resistance. Continuous use temperature is 260 â??.
- It retains flexibility without losing toughness under the environment from cryogenic to high temperature.
- Low dielectric constant and dielectric loss tangent in a wide range of temperature and frequency.
- It shows high electrical resistance and dielectric strength.
- Nonflammable like POLYFLON PTFE and NEOFLON FEP.
- Excellent weather resistance. No properties change even when exposed outside for a long time.
- Non-stickiness. It shows excellent releasability and water repellency / oil repellency.
NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom.
It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins.
NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom.
It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins.
NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom.
It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins.
NEOFLON PFA is a copolymer of tetrafluoroethylene and perfluoroalkyl vinylether. It is a perfluoro polymer consisting of only carbon atoms and fluorine atoms without any hydrogen atom.
It has the same excellent performance as PTFE in a wide range from extremely low to high temperatures. In addition, it has excellent transparency, mechanical strength at high temperature. It can be molded in the same molding method as general thermoplastic resins.
Grades and Features of AP-Series
Grades MFR
(g/10 min.) Features
AP-201 20 - 30 Superior in melt flowability.
Suitable for injection-molded articles that have complex shape, and for ultrafine thin-wire coating (AWG34 - 44).
AP-202 65 - 80 Excellent melt flowability.
Suitable for injection-molded articles that have complex shape, and for thin-wire coating (AWG44 - 52).
AP-210 10 - 17 Good melt flowability.
Suitable for injection molding.
AP-230 1.5 - 2.5 Superior in stress crack resistance.
Suitable for extrusion and transfer molding.
AP-201SH 20 - 30 High purity grade.
Superior in melt flowability.
Suitable for complex shape articles.
AP-211SH 10 - 17 High purity grade.
Long-term flexibility and good stress crack resistance.
Suitable for joints and parts for pumps.
AP-215SH 10 - 17 High purity grade.
Suitable for injection molding.
Suitable for joints and parts for pumps.
AP-231SH 1.5 - 2.5 High purity grade.
Long-term flexibility and good stress crack resistance.
Suitable for extrusion and transfer molding.
AP-210AS 11 - 14 Anti-static grade.
Suitable for injection molding.
AP-230AS 1.5 - 3.0 Anti-static grade.
Suitable for extrusion molding.
AP-230ASL 1.0 - 2.5 Anti-static grade.
Suitable for extrusion molding.
61 Neoflon Pfa Ap 210 Daikin Suppliers
Short on time? Let Neoflon Pfa Ap 210 Daikin sellers contact you.
NEOFLON ETFE is a copolymer of tetrafluoroethylene and ethylene, and has the lowest specific gravity among all fluoropolymers. It has superior characteristics in melt processability and mechanical properties compared with PTFE and FEP, and has good electrical and chemical properties. It is suitable for applications requiring its mechanical toughness, chemical resistance, heat resistance and electrical properties.
NEOFLON ETFE EP-506 is a resin for extrusion of thin coatingsof small wire sizessuch as aerospace wire, automotive wire, appliance wire, thin film and tubing, etc.. Itmay be used for injection molding of thin wall parts.
Ethylene tetrafluoroethylene copolymer is a kind of chemical substance. ETFE is the strongest and toughest fluoroplastic. It not only maintains the good heat resistance, chemical resistance and electrical insulation properties of PTFE, but also greatly improves the radiation resistance and mechanical properties. The tensile strength can reach 50MPa, which is nearly twice that of polytetrafluoroethylene.
NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene.
FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
NEOFLON ETFE EP-506 is a resin for extrusion of thin coatingsof small wire sizessuch as aerospace wire, automotive wire, appliance wire, thin film and tubing, etc.. Itmay be used for injection molding of thin wall parts.
Ethylene tetrafluoroethylene copolymer is a kind of chemical substance. ETFE is the strongest and toughest fluoroplastic. It not only maintains the good heat resistance, chemical resistance and electrical insulation properties of PTFE, but also greatly improves the radiation resistance and mechanical properties. The tensile strength can reach 50MPa, which is nearly twice that of polytetrafluoroethylene.
NEOFLON FEP NP-Series
NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene.
FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
NEOFLON FEP NP-Series
NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene.
FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene.
FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene.
FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
Grades and Features of NP-Series
Grades MFR
(g/10 min.) Features
NP-20 4.5 - 8.5 Suitable for general extrusion molding of wire coating, pipes, tubes and films.
NP-30 2.0 - 3.5 Suitable for thick-walled wire coating and wire jacket.
NP-101 21 - 27 Improved melt flowability.
Best suited for high-speed wire coating such as LAN cable.
NP-120 4 - 10 Stress crack resistance is improved from NP-20.
Wide range of applications, from thin-walled to thick-walled wire coating.
We can give discount according to order quantity.
NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene.
FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
Grades and Features of NP-Series
Grades MFR
(g/10 min.) Features
NP-20 4.5 - 8.5 Suitable for general extrusion molding of wire coating, pipes, tubes and films.
NP-30 2.0 - 3.5 Suitable for thick-walled wire coating and wire jacket.
NP-101 21 - 27 Improved melt flowability.
Best suited for high-speed wire coating such as LAN cable.
NP-120 4 - 10 Stress crack resistance is improved from NP-20.
Wide range of applications, from thin-walled to thick-walled wire coating.
We can give discount according to order quantity.
NEOFLON FEP NP-Series
NEOFLON FEP is melt processable perfluoro co-polymer of tetrafluoroethylene and hexafluoropropylene.
FEP has excellent electrical properties like PTFE because FEP consists of only fluorine atoms and carbon atoms. The chemical resistance capability and mechanical characteristics are the same as ones of PFA, however the heat resistance is lower than PFA.
POLYFLON PTFE is composed of polytetrafuluoroethylene, the most commonly used fluoroploymer. PTFE has a very long chain molecular structure in which all of the hydrogen atoms of polyethylene are replaced by fluorine atoms.
PTFE is superior in heat resistance and chemical resistance compared with the other plastics. These properties result from stable chemical structure consisting of only carbon and fluorine atoms with the highest electro negativity.
Desktop Alert has confirmed with Alpha Protech that the PO issued by Desktop Alert to Alpha Protech (AP) for 5 million respirators will be fulfilled during the 4th quarter 2020 with an assurance that all will be shipped before EOY. AP is a US publicly traded company on NASDAQ.
Cases Per Pallet :
96 cases
210 Respirators Per Case
Pallet Details :
800lbs
20,160 pieces
Inventory Validation :
Desktop Alert will conduct a conference call at the buyer's request with C Level officers at AP.
Shipping will start as early as late September
ny reason by buyer. Buyer may choose their own escrow attorney. Escrow released when shipper validates landing of the inventory. Each release amount from the escrow account is measured on the actual piece count release per shipment as we are talking about many tractor trailers loads across the 4th quarter 2020. Buyer is responsible for shipping insurance if desired.
POLYFLON PTFE is composed of polytetrafuluoroethylene, the most commonly used fluoroploymer. PTFE has a very long chain molecular structure in which all of the hydrogen atoms of polyethylene are replaced by fluorine atoms.
PTFE is superior in heat resistance and chemical resistance compared with the other plastics. These properties result from stable chemical structure consisting of only carbon and fluorine atoms with the highest electro negativity.
