S&A CW-6200AT dual temperature and dual pump series is high-precision compression refrigeration water chiller,with intelligent temperature control,completed configuration,perfect protection and alarm system, it is applied to cool 1KW laser source of IPG, MaxPhotonics and nLIGHT.
S&A CW-6200AT is able to cool the fiber laser and optic lense at the same time, multiple use for saving cost, space and manual move, quiteconvenient for the user.
Features
1. 5100W cooling capacity; optional environmental refrigerant;
2. ±0.5â?? precisely temperature control;
3. The intelligent temperature controller has 2 control modes, applicable to different applied occasions; with various setting and display functions;
4. Dual temperature and dual pump to satisfy different needs of fiber laser device and the lens;
5. With Ion adsorption filtrating and test functions conform to fiber laser device operating requirements;
6. Multiple alarm functions: compressor time-delay protection, compressor overcurrent protection, water flow alarm and over high / low temperature alarm;
7. Multiple power specifications; CE approval; RoHS approval; REACH approval;
8. Long working life and easy operation;
9. Optional heater and water filter.
Model CW-6200AT CW-6200BT
Voltage 220V 220V
Frequency 50Hz 60Hz
Current 2~13A
Compressor power 1.68KW 1.65KW
2.24HP 2.2HP
High + low temp system refrigeration capacity 1706 Btu/h+15820 Btu/h 1706 Btu/h+15940 Btu/h
0.5 KW+4.63 KW 0.5 KW+4.67 KW
430 Kcal/h+3986 Kcal/h 430 Kcal/h+4016 Kcal/h
Refrigerant R-22 / R-410a
Refrigerant charge 1300g 1300g
Precision ±0.5â??
Reducer Capillary
Protection Overcurrent protection for compressor, flow alarm, over temperature alarm
High + low temp pump power 0.1KW + 0.55KW
High + low temp tank capacity 4L + 12L
High + low temp pump lift 25M + 36M
High + low temp inlet and outlet Rp1/2" + Rp1/2"
High + low temp pump flow 16L/min + 70L/min
N.W 92Kgs
G.W 102Kgs
Dimension 78 x 47 x 89 cm (L x W x H)
Package dimension 87 x 60 x 109 cm (L x W x H)
TLD1500 Series is high quality of Optical Fiber Checker. It contains the most advanced laser technology and microelectronics technology, and can be measured with various fiber optic adapter with 2.5mm common Interface. It is very convenient for them to check the single-mode and multimode fiber.
Laser Source Power Meter
The Laser Source Power Meter provides an economical, stable laser source for point-to-point attenuation measurements. It features a rugged design that withstands the harsh test environments of fiber optic cable installation and maintenance.
Compact in size, inexpensive, lightweight with low power consumption diode laser is housed in a plastic moulded case (90x90x42) mm approx., qualitatively used for ray optics demonstration and simple diffraction work as well as to indicate the points on overhead images and charts. It required three button cells to project visible red spot with a sharply focused beam of wavelength (630-680) nm with only 1mw power consumption.
DFB Light Source/Hoyatek tunable DWDM 100mW
Features:
high output power
excellent power stability and wavelength stability
itu-t recommended standard channel
channel space 25/50/100ghz
provide half a custom processing
Applications:
optical component produce and testing
optical communication system testing
fiber sensing system
hfc network
catv network
The UV laser marking machine is developed by using a 355nm UV laser. This machine uses a third-order intracavity frequency doubling technology. Compared with infrared lasers, the 355nm UV laser has a very small spot, and the marking effect is directly interrupted by a short-wavelength laser. The molecular chain greatly reduces the mechanical deformation of the material. Thermal deformation (cold light), because it is mainly used for ultra-fine marking and engraving. It is especially suitable for applications such as marking, micro-hole drilling of food and pharmaceutical packaging materials, high-speed dicing of glass materials, and complex pattern cutting of silicon wafers.
Features
Color LCD monitor & 256 magnification
Compact & light weight
Reversible monitor with control panel on each side
Max. Wind velocity of 15m/s.
8 sec. Splice time, 40 sec. Tube-heat time
Simultaneous x and y views
Large capacity internal battery
System test ensures the best working condition
User programmable
Auto check fiber end face
Auto calibrate parameters
Store 8000 groups of splice results
Multiple language options
Specifications
ModelDvp-730
Applicable fibersSm, mm, ds, nz-ds, edf
Cladding diameter100 to 150um
Coating diameter100 to 1000um
Fiber cleaved length8-22mm (standard)
Splicing modeAuto & manual
Average splice loss0.02db(sm), 0.01db(mm), 0.04db(ds), 0.04db(nzds)
Return loss 60db
Environment conditions-25-+50(operation temperature), 0-95%rh(humidity), 0-5000m (altitude)
Storage environment-40-+80(temperature), 0-95rh (humidity)
Protection sleeve length20mm, 40mm, 60mm
Tension test2.0n (standard)
LanguageEnglish, chinese, korea, russian, spanish etc.
InterfaceRs232 interface & video output
Power supplyAc adaptor: 85-260v input voltage
Internal battery: 12v voltage, 10ah, up to 200 times of continuous splices and heatsdc adaptor: 12v voltage, optional multipurpose external battery
Dimensions170(w)140(h)170(d)mm
Weight3.3kg.
Fusion splicer pt-660
Features
Color lcd monitor and 256x magnification
Compact and lightweight
Reversible monitor with control panel on each side
Maximum wind velocity: 15m/s
8sec splice time, 40sec tube-heat time
Simultaneous x and y views
Large capacity internal battery
System test: ensures the best working condition
User programmable
Auto check fiber end face
Auto calibrate parameters
Store 8, 000 groups of splice results
Multiple language options
Specification
Model Pt-660
Applicable fibers Sm (itu-t g.652), mm (itu-t g.651), ds (itu-t g.653), nzds (itu-t g.655)
Fiber cleaved length 12~16mmú¿coating diameterú¦250ª8mú¬
16mmú¿coating diameter: 250 ~ 1000ª8mú¬
Fiber diameter Cladding diameterú¦80 ~150ª8m
Coating diameterú¦100~ 1000ª8m
Fiber count Single
Fiber aligning method Core or clad aligning
Image processing method Digital
Actual average splice loss 0.02db ú¿smú¬, 0.01db (mm),
0.04db (ds), 0.04db( nzds)
Splicing time Typical 8 secú¼with standard sm fiber
Splicing mode 53(templet), 40(user)
Splice loss estimate More accurate
Return loss ú+60db
Storage of splice result 4000 resultsú¼20 parameter per result
Fiber display and magnification 300xú¿x or y viewú¬, 150xú¿x and y viewú¬
Tube heating time Typical 30 sec
Tube heating mode 8(templet), 24(user)
Tube heating temperature Can be adjusted
Applicable protection sleeve length 60mm, 40mm and a series of micro sleeves
Tension test 2n
Electrode life 2500
No.Of splice/heating with battery Typical 150 cycles (splice/tube heat) with inner li-battery
Display screen 5 inch color lcd monitor
Image change over The fiber image is turned upside down
Terminals Usb 1.1 and vga
Operating condition 0 ~ 5000m above sea level, 0 ~ 95%rh and -10í½50íµ, respectively, max. Wind velocity of 15m/s
Power supply Ac 100-240v with ac adapter; inner li-battery(6600mah)
Dimensions 170mm(l) x170mm (w) x140mm (h)
Weight 2.7 kg excluding battery, 3.3 kg including battery
Feature
1mW red laser output, test scope more than 5km
650nm highlight red laser output, convert between CW and 2Hz
Universal interface adapter, suit for FC, SC and ST.
Stable single or multi mode of wavelength, CW or 2KHz
Big LCD show working wavelength state
One press to shift work wavelength, flexible to operate.
Technique Parameter
Model DT-605A DT-605B DT-605P
Output wavelength 850nm /1300nm 1310nm /1550nm 1300nm /1490nm /1550nm
Output power -10dBm -5dBm -5dBm
Laser type LD
Spectrum range 850nm@10nm ; 1300nm/1310nm/1490nm/1550nm@5nm
Stability 0. 01dB@5 minutes£»0. 1dB@24 hours
Connector type FC/PC £»Customized ST or SC
Fiber type SM¡¢MM
Audio load wave 270Hz, 1KHz, 2KHz
Display info Wavelength¡¢Battery¡¢carrier wave state
Power auto on/off 10 minutes
Battery type AA alkaline cell, rechargeable lithium battery
Continuous working time >40h
1. Lightweight,energy-saving and maintenance-free Integrated air-cooled structure. Volume only 0.15m�³.
2. 6 preset cleaning processes+ 3 custom ones Corresponding to different usage requirements. Simple operation.
3. Double-wobble Cleaning Head Scanning width up to 190mm.
4. 8 Light Modes Meet various operation requirements.
5. High Power Density and Strong Output.Energy is twice that of ordinary models, effectively addresses issues of difficult cleaning and inefficiency.
Advantages of fiber laser marking machine 20w
Wide range: can be used on many materials like metal, plastic, leather, alloy etc. Can be used in many industries like jewelry engraving, medical devices, phone case engraving, hardware industry, stainless steel tableware, electron components marking etc.
Permanent marking: laser marking is a permanent marking. It won¡¡¥t fade, run or become less discernable as time passes like traditional marking including ink jet, hand engraving, dot-peen marking.
Long service time: fiber laser model has a over 100, 000 hours working life. Almost no maintenance during this period.
Easy to operate: support almost any windows-based software like coreldraw, autocad, photoshop. No need to adjust q-switch easier than yag diode marking machine.
High precision: 0.0025mm re-position accuracy. Minimum line width 0.01mm.
Non-contact process: won¡¡¥t cause mechanical extrusion or mechanical stress to materials.
Advantages of fiber laser marking machine 20w
Wide range: can be used on many materials like metal, plastic, leather, alloy etc. Can be used in many industries like jewelry engraving, medical devices, phone case engraving, hardware industry, stainless steel tableware, electron components marking etc.
Environmentally friendly: using no harsh chemicals during the process. No need water chiller to cool, small size small occupation, can be easily installed in many places.
Cost-effective: no maintenance during the 100, 000 hours working life. One machine can be used in many different materials & industry. Marking software c/w machine. Minimal part replacement
High efficiency: computer operated, suitable for automatically processing(like production line, automatically filling line). Marking speed is 7000mm/s.
Full supporting: warranty two year. Full operator training. Our engineers providing a solution according to your application. Engineers available service machinery overseas.
High quality: ce & iso & bv & fda approved, imported core spare parts like german ipg fiber laser.
Advantages of fiber laser marking machine 20w
Wide range: can be used on many materials like metal, plastic, leather, alloy etc. Can be used in many industries like jewelry engraving, medical devices, phone case engraving, hardware industry, stainless steel tableware, electron components marking etc.
Permanent marking: laser marking is a permanent marking. It won¡¡¥t fade, run or become less discernable as time passes like traditional marking including ink jet, hand engraving, dot-peen marking.
Cost-effective: no maintenance during the 100, 000 hours working life. One machine can be used in many different materials & industry. Marking software c/w machine. Minimal part replacement
High efficiency: computer operated, suitable for automatically processing(like production line, automatically filling line). Marking speed is 7000mm/s.
Full supporting: warranty two year. Full operator training. Our engineers providing a solution according to your application. Engineers available service machinery overseas.
High quality: ce & iso & bv & fda approved, imported core spare parts like german ipg fiber laser.
Features:
To meet the demand of multi-composite light source, multi-wavelength light source system is developed. The multi-wavelength light source uses imported laser and efficient driving circuit, which guarantee the system optical output power stable. The multi-wavelength light source can achieve the combination of arbitrary wavelength. The inside is integrated of mems optical switch, which can switch the wavelength by the panel buttons or rs232 interface.
