The cv7 range of products features lateral transducers delivering four independent measurements. The validity checks are used to measure head wind vectors for calculations. This method gives a wind speed sensitivity of 0.15 m/s, and reliability and excellent linearity up to 40 m/s.
Cv7-v ultrasonic wind speed sensor specification:
Output data format: nmea0183; mwv, xdr
Information transmited: instant. W. Speed, instant. W. Angle, avaibility
Output rate: 2 hz / 30 hz measurement
Wind module sensitivity: 0.12 m/s
Wind module resolution: 0.05 m/s
Wind module dynamic: 0.12 to 40 m/s
Direction sensitivity: +/-1.5'
Direction resolution: 1'
Power supply: 8 v to 30 v dc
Electrical consumption: 9 ma
Op. Temp. Without icing: -15'c to +55'c
Cable: 25 m / 4x0.22 mm2
Connection: 4 wires
Weight of the head: 100 gr
Weight of unit assembly: 200 gr with mounting part
Mounting: vertical ; 300 aluminium arm, 16 mm
CV7-V Ultrasonic Wind Speed Sensor Description
The CV7 is easily integrated into measurement and monitoring systems. The CV7-V is powered by 8-30 VDC power supply and it outputs RS232/RS422 (5V level signal) / NMEA0183.
CV7-V Ultrasonic Wind Speed Sensor Application
Static wind sensor
A conventional wind vane/anemometer features mechanical rotating parts. These moving parts expose the sensor to failure.
CV7 series was extensively tested in Marine applications for both precision and robustness.
Configurable wind sensor
CV7-V can be programmed and configured for : angle correction, smoothing time constant, units of measurement and interface format.
CV7-V connexion
CV7-V can be used connected to a PC and any systems featuring an NMEA® input port and specific pieces of equipment using conventional formats.
In PC mode, this bidirectional sensor can be set up for angle correction, damping, measure units and interface format.
Quality
All LCJ Capteurs are designed and manufactured in the Nantes region in France where they are fully tested throughout the manufacturing process.
CV7-V Ultrasonic Wind Speed Sensor Specification:
Output data format: NMEA0183; MWV, XDR
Information transmited: Instant. W. Speed, Instant. W. Angle, avaibility
Output rate: 2 Hz / 30 Hz measurement
Wind module sensitivity: 0.12 m/s
Wind module resolution: 0.05 m/s
Wind module dynamic: 0.12 to 40 m/s
Direction sensitivity: +/-1.5 degree
Direction resolution: 1 degree
Power supply: 8 V to 30 V DC
Electrical consumption: 9 mA
Op. temp. without icing: -15 degree C to +55 degree C
Cable: 25 m / 4x0.22 mm2
Connection: 4 wires
Weight of the head: 100 gr
Weight of unit assembly: 200 gr with mounting part
Mounting: Vertical ; 300 aluminium arm, 16 mm
Cv7-e ultrasonic wind speed sensor description
The cv7-e is easily integrated into measurement and monitoring systems. Detects gusts with great responsiveness and low latency. The cv7-e is powered by 8-30 vdc power supply and it outputs rs232 / rs422 / 5 v level signal / nmea0183.
The cv7-e shows a data rate twice faster than the cv7 and cv7-v with a data output 4 per second.
The small size of this sensor makes it very discreet.
Like every lcj capteurs products, cv7-e is energy efficient.
Cv7-e has proved its value with universities â??laboratories, scientific and wind tunnels successful tests.
It can be used connected to a pc and to any system featuring a nmeaâ® input port.
Cv7-e ultrasonic wind speed sensor specification:
* output data format: nmea0183, mwv, xdr
* information transmited: instant. W. Speed, instant. W. Angle, avaibility
* output rate: 4 hz / 60 hz measurement
* wind module sensitivity: 0.12 m/s
* wind module resolution: 0.05 m/s
* wind module dynamic: 0.12 to 40 m/s
* direction sensitivity: +/-1.5'
* direction resolution: 1'
* power supply: 8 v to 30 v dc
* electrical consumption: 9 ma
* op. Temp. Without icing: -15'c to +50'c
* cable: 25 cm / 4 x 0.22 mm2, 20 g/m
* connection: 4 wires
* weight of the head: 100 gr
* weight of unit assembly: 200 gr with mounting parts.
CV7-OEM Ultrasonic Wind Speed Sensor Description
CV7-OEM shows the same features as the CV7 standard: light, compact and low energy consumption.
With this OEM version of the Static Wind Transducer CV7, you can add an accurate Ultrasonic Wind Sensor to your own products and installations. It is powered by 8-30 VDC power supply and it outputs RS232/RS422/NMEA0183 signal.
CV7-OEM Ultrasonic Wind Speed Sensor Specification:
* Output rate: 2 Hz / 30 Hz measurement or *4 Hz / 60 Hz meas.
* Wind module sensitivity: 0.12 m/s
* Wind module resolution: 0.05 m/s
* Wind module dynamic: 0.12 to 40 m/s
* Direction sensitivity: +/-1.5 degree
* Direction resolution: 1 degree
* Power supply: 8 V to 30 V DC
* Electrical consumption: 9 mA
* Op. temp. without icing: -15 degree C to +55 degree C
CV7-E Ultrasonic Wind Speed Sensor Description
The CV7-E is easily integrated into measurement and monitoring systems. Detects gusts with great responsiveness and low latency. The CV7-E is powered by 8-30 VDC power supply and it outputs RS232 / RS422 / 5 V level signal / NMEA0183.
The CV7-E shows a data rate twice faster than the CV7 and CV7-V with a data output 4 per second.
The small size of this sensor makes it very discreet.
Like every LCJ Capteurs products, CV7-E is energy efficient.
CV7-E has proved its value with universities â??laboratories, scientific and wind tunnels successful tests.
It can be used connected to a PC and to any system featuring a NMEA® input port.
CV7-E Ultrasonic Wind Speed Sensor Specification:
* Output rate: 4 Hz / 60 Hz measurement
* Wind module sensitivity: 0.12 m/s
* Wind module resolution: 0.05 m/s
* Wind module dynamic: 0.12 to 40 m/s
* Direction sensitivity: +/-1.5 degree
* Direction resolution: 1 degree
* Power supply: 8 V to 30 V DC
* Electrical consumption: 9 mA
* Op. temp. without icing: -15 degree C to +50 degree C
-
6497 Cv7 V Ultrasonic Wind Speed Sensor Suppliers
Short on time? Let Cv7 V Ultrasonic Wind Speed Sensor sellers contact you.
This is a low-cost anemometer, which utilises proven ultrasonic technology to provide wind speed and direction data via one serial or two analogue outputs. To confirm correct operation, outputs are transmitted together with an instrument status code. With a robust, corrosion-free polycarbonate housing, this small, lightweight wind sensor is recommended for use in harsh environmental conditions and is particularly suited to marine & offshore (ships, data buoys) and land based installations. The WindSon has no moving parts, offering maintenance-free operation in a wide range of applications.
Sonic-anemo-sdi ultrasonic wind speed sensor description
Sonic-anemo-sdi is made from the cv7-v to which a sdi12 protocol and optimizing electrical consumption has been added. Sample rate is 2 hz.
This ultrasonic wind sensor operates in a request-response mode.
This product is more energy-efficient than standard units.
The sonic-anemo-sdi is dedicated to meteorological applications.
Sonic-anemo-sdi ultrasonic wind speed sensor available data:
- average speed and direction over 10 minutes
- minimum wind speed and direction for that period
- maximum wind speed (gust 3s) and direction for that period
- software version and serial number
- data measurement quality rate from the sensor
- data for sensor diagnostic (manufacturer use only)
Sonic-anemo-sdi ultrasonic wind speed sensor specification:
* output data format: sdi-12 v1.3
* information transmited: inst. W. Speed, w. Angle, gust ws/wa, avg, min, max, avaibility
* output rate: 2 hz / 30 hz measurement
* wind module sensitivity: 0.12 m/s
* wind module resolution: 0.05 m/s
* wind module dynamic: 0.12 to 40 m/s
* direction sensitivity: +/-1.5'
* direction resolution: 1'
* power supply: 2.7 v to 35 v dc
* electrical consumption: 2.9 ma avg. @ 12 v
* op. Temp. Without icing: -15'c to +55'c
* cable: 5 m / 3 x 0.22 mm2 uv proof
* connection: 3 wires
* weight of unit assembly: 200 gr with mounting parts.
Sonic-anemo-dzp ultrasonic wind speed sensor description:
Sonic-anemo-dzp ultrasonic anemometer is powered by its own solar panel. It is well suited to remote installations where power consumption matters. This unit connects directly to a pulse or potentiometer input (i.E. On davis instruments). It is a useful product for professionals, integration to aws (autonomous weather station), and well-informed users.
Sonic-anemo-dzp ultrasonic wind speed sensor specification:
, output rate: 1 measure and update per second
, wind module sensitivity: 0.12 m/s
, wind module resolution: 0.05 m/s
, wind module dynamic: 0.12 to 40 m/s
, direction sensitivity: +/-1.5'
, direction resolution: 1' (9 bits)
, power supply: photovoltaic panel, battery lifepo4
, op. Temp. Without icing: -15'c to +55'c
SONIC-ANEMO-DVC Ultrasonic Wind Speed Sensor Description:
As Worldwide Premiere launch, a specific version of the CV7-V which connects directly to the wind sensor input on Davis instruments.
This sensor will allow the replacement of mechanical anemometers / wind vanes with no need of anything else but power supply.
Itâ??s an exclusive and useful product for both, professionals and well-informed amateurs.
SONIC-ANEMO-DVC Ultrasonic Wind Speed Sensor Specification:
* Output rat: 2 Hz / 30 Hz measurement
* Wind module sensitivity: 0.12 m/s
* Wind module resolution: 0.05 m/s (16 bits)
* Wind module dynamic: 0.12 to 40 m/s
* Direction sensitivity: +/-1.5'
* Direction resolution: 1' (9 bits)
* Power supply: 2.7 V to 35 V DC
* Electrical consumption: 2.6 mA Avg. @ 12 V
* Op. temp. without icing: -15'C to +55'C
SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Description
SONIC-ANEMO-SDI is made from the CV7-V to which a SDI12 protocol and optimizing electrical consumption has been added. Sample rate is 2 Hz.
This ultrasonic wind sensor operates in a request-response mode.
This product is more energy-efficient than standard units.
The SONIC-ANEMO-SDI is dedicated to meteorological applications.
SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Available data:
- Average speed and direction over 10 minutes
- Minimum wind speed and direction for that period
- Maximum wind speed (gust 3s) and direction for that period
- Software version and serial number
- Data measurement quality rate from the sensor
- Data for sensor diagnostic (manufacturer use only)
SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Specification:
* Output rate: 2 Hz / 30 Hz measurement
* Wind module sensitivity: 0.12 m/s
* Wind module resolution: 0.05 m/s
* Wind module dynamic: 0.12 to 40 m/s
* Direction sensitivity: +/-1.5'
* Direction resolution: 1'
* Power supply: 2.7 V to 35 V DC
* Electrical consumption: 2.9 mA Avg. @ 12 V
* Op. temp. without icing: -15'C to +55'C
SONIC-ANEMO-MICRO Ultrasonic Wind Speed Sensor Description:
As a result of its very special electronic architecture the SONIC-ANEMO-MICRO shows a very low electrical consumption. It is ideal for remote stations or mobile installation.
SONIC-ANEMO-MICRO is an OEM sensor designed for integration in other original Equipment.
This sensor shows a very low consumption. It operates from 300µA.
SONIC-ANEMO-MICRO is the lowest consumption power solution of all LCJ sensors.
SONIC-ANEMO-MICRO Ultrasonic Wind Speed Sensor Specification:
Output data format: ASCII format, avaibility
Information transmited: Instant. W. Speed, Instant. W. Angle, avaibility
Output rate: select. 1 meas. and Tx: every 1,6 or 18 s
Wind module sensitivity: 0.12 m/s
Wind module resolution: 0.05 m/s
Wind module dynamic: 0.12 to 40 m/s
Direction sensitivity: +/-1.5 degree
Direction resolution: 1 degree
Power supply: 3 V to 3.6 V DC
Electrical consumption: 200µA avg
Op. temp. without icing: -15 degree C to +50 degree C
Cable: 50 cm / 4x0.22 mm2
Connection: 4 wires
Weight of the head: 100 gr
Weight of unit assembly: N/A
Mounting: N/A
New designed High Speed fruit slice machine,can slice lemon,orange,apple,pear,kiwi ... same this kind oval and round fruit vegetable can process
Parameters :
External dimensions: 2800 * 1200 * 1250 mm
Input voltage: 220 V
Total power: 3 kw
Production: 90-120 pcs/min
Total weight: 340 kg
Health fruit slice for people eating, good business ! welcome cooperate! contact us
fruit slicer machine
lemon slice machine
Stick ice lollipop ice filling sealing machine
The automatic stick ice filling -sealing machine for lollipop ice is small in size and light in weight, and is made of stainless steel. This machine can produce various beverages such as lollipop ice, milk sticks, fruit milk, fruit cold drinks, and so on. from small capacity to big capacity .
Product parameters of one :
Voltage: 220/50 (V/Hz)
Power: 0.75KW
Sealing speed: 2000 cups/hour
Filling capacity 0-150ml
Specification: 960 * 430 * 330mm
(Welcome give thumbs-up, comment,transmit)
welcome order !
2-head packaging machine (also can 4-18head according different capacity choice)
Packaging speed 15bags/min
Bag length 90-320mm
Bag width 80-210mm
Overall weight 400kg
Power 1.8kw/220v
Packaging capacity 20-1000ml
Outer packaging size 820 x1220 x 2500mm
Packaging form Back sealing
This machine is an intelligent weighing automatic quantitative packaging machine with four scales and microcomputer control. Suitable for quantitative packaging of granular materials such as miscellaneous grains, nuts ,pesticides, fertilizers, veterinary drugs, premixes, additives, laundry detergent, salt, monosodium glutamate, white sugar, seeds, rice, snacks, hardware, etc.
Performance characteristics:
1. High precision digital sensors enable precise measurement to be achieved instantly.
2. The microcomputer control system is technologically advanced, easy to operate, and more reliable to use.
3. Fast and slow vibration feeding, automatic correction of errors, achieving high-precision packaging.
4. Four scales work alternately, with fast packaging speed.
5. High quality stainless steel is used for the material contact part, which is anti-corrosion, dust-proof, and easy to clean.
Host configuration:
This machine is equipped with a dual CPU microcomputer control system, a 5-inch LCD display in Chinese or English, a user-friendly operation interface, automatic cursor detection and tracking, and simpler operation. Equipped with high-precision stepper motors to ensure the accuracy of the cutting position of each packaging bag.
Carbon fish meat grill oven process:
A. special high temperature resisitant material,high heat deformation,the overall structure uses professtional plate ;
B.all into oxygen at the bottom of the damper desigh,fast burning heat rapidly ,at teh top of the air valve design,effective control of heat loss;
C. origianl putty separation technology,completely avoiding using process because of the putty mixed soot and open flame,ensure clean,health and safety ;
D.equipment applied double high temperature heat insulation material,insulation system,insulation with security,external direct touch with no hidden dangers.
Operation method:
A. all burning charcoal in the burning charcoal ,open at the top the smooke at the bottom of the mouth and damper;
B.charcoal burning closed 10 minutes to the degree of smoke-free smoke at the top of the mouth,the heat;
C.after the temperature reaches the standard,in the baking objects to buy object ;
D.5-10minutes,bake fish until brown on both sides,are taken from the furnace, the plate feeding .
Equipment advantages :
A. unique design principle ,the use of charcoal smoke all gathered in the grilled fish inside furnace,through the top of the exhaust pipe directly emitted;
B.rapid heat,guarantee the production speed,let the charcoal furnace cavity fully burning rapied heating up,wind valve,and through the top to the bottom of the design of air supply outlet temperature in the furnace in a 300-350 degree,put the fish in the distribution on the stove on content cabinet ,only 8-10 minutes can be produced;
C. a novel view and admire a gender ,the design of the gear type appeared in front of customers,the grilled fish process more transparent,more ornamental ,fish and clients directly face to face "communication " ;
D this design flexibility ,the real achieve a multi-purpose furnace, can bakering chicken duck cattle and sheep for equipment use diversification more rich .
Fuel: dual-use carbon box ,burning charcoal or alcohol (vegetable oil ) ,pump design.
Installation and commissioning
Overall production : have direct admission requiements,no installation commissioning ,one pace reachs the designated position .
1.Solve the smoke problem charcoal grilled fish
we are familiar with most of the fish appeared in the night street food stalls ,a rectangular fish furnace ,a big fan, the air is filled with smoke smell fish .
Our wind speed sensors have proven themselves in wind tunnel tests, in mountain-top tests and in thousands of household and institutional installations to be rugged, reliable and highly accurate.The type #41 generator has recorded wind to 214 mph.
Their low moment of inertia and unique bearings permit very rapid response to gusts and lulls. The black lexan cups (virtually shatter-proof) have thermal propertieswhich let it resist and shed icing far more effectively than metal assem-blies. Because of their output linearity these sensors are ideal for use with various data retrieval systems. The experience that maximum hasbuilt up over the years has provided the basis of our solid confidencein these sensors for a wide variety of applications.
Wind speed sensor 400 environmental
Operating temperature: -67 to + 130 degrees f
Operating humidity range: 10 to 100% rh
Wind speed sensor 400 technical specifications
* 3 cups of conical cross-section, 2" diameter. 7.5" swept diameter of rotor.
* 2 diameter housing.
* 3.2 overall assembly height.
* moment of inertia of rotor assembly = 68 x 10-6 x s-ftâ². Material of cups is black lexan.
* material of housing is black abs.
* shaft material is beryllium copper; fully hardened. Upper and lower bearings of modified teflon, self-lubricating.
* they have a rated pv factor of 20, 000 (at 15mph, pv is approx. 500; at 100mph pv is approx. 2, 000).
* upper bearing is centered in the plane of cup thrust for optimal loading.
* permanent magnet: indox 1, 1"dia. Long, 4 poles. Generators mount (using a cotter pin) on a 0.500" diameter mast with a #35 hole 0.350" from top of mast.
* starting threshold < = 4 mph distance constant 10 feet
The gearbox of a wind turbine is one of the key components in wind power generation equipment, used to transfer the kinetic energy of the rotating wind turbine to the generator, thereby generating electrical energy. It is usually composed of multiple gears, which increase the speed of the wind turbine through precise transmission ratios and convert it into a speed suitable for the operation of the generator. Usually, the speed of the wind turbine is very low and far from the required speed for the generator to generate electricity. It must be achieved through the speed increasing effect of the gearbox gear pair, so the gearbox is also called a speed increasing gearbox.
The variable pitch gear box is an important part of the fan variable pitch system, its main function is to increase the torque of the variable pitch motor on the variable pitch bearing, drive the blade to change the blade pitch Angle at different wind speeds, so that the blade is in the best state of absorbing wind energy, and can drive the blade feathering brake when the wind speed exceeds the cutting wind speed, so as to ensure the machine to run efficiently and smoothly.
The variable gear box transmission mechanism is composed of multiple planetary gear trains, usually 3 stages, and the planetary transmission form is NGW type.
TRM-500 is designed to make twisted paper ropes are widely used to make handle for shopping bags. Rope made from the machine can be of different diameters as per the requirement. Itâ??s a high speed and high production twisted paper rope manufacturing machine. Fully automatic and require less manpower to operate. Paper roll of desired width is put at one end and at the other end e-winded twisted rope is made.
6497 Cv7 V Ultrasonic Wind Speed Sensor Suppliers
Short on time? Let Cv7 V Ultrasonic Wind Speed Sensor sellers contact you.
