Advanced modular towers (Steel-Frame Volumetric Systems) engineered for urban density.
Designed for safety and durability (Seismic & Wind-Load Compliance).
Guru is a large Global supplier of 89% Refractory Insulation Castables. We have a high-performance product range of high-quality, specification based castables. Our manufacturers are the worlds best companies providing great innovative products. We have been assocoated with our vendors since the past five decades. We also have a complete team of engineers, site supervisors & applicators for complete turnkey projects worldwide.
92% Ferro Silica Fume meets the creteria of most of the relevent international and Indian Standard specification. Its packed in 25 kg bags & Big 1 mt Jumbo Bags from Ahmedabad, Gujarat. Microsilica is a highly reactive pozzolan and gives concrete a denser microstructure, lower permeability higher electrical resistivity leading to improved durability.
Combined with correct design and workmanship, microsilica concrete offers characteristics that will ensure long term durability and service life. It durability of a reinforced concrete structure can be defined as the capability of the structure to maintain its original functional and structural characteristics during the expected service life in the exposure conditions it was intended for.
Method of Uses:
The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes.
Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
Packaging: G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
Storage: G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25�°C, protected from heat, frost and direct sunlight.
Safety Information: Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation.
It is recommended that suitable protective clothing, gloves and eye/face protection is worn.
In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
153379 Construction Materials Suppliers
Short on time? Let Construction Materials sellers contact you.
G-FINE ULTRAFINE is a new generation Supplementary Cementitious material (SCM) with a built-in high tech content. It is processed based on high glass content with high reactivity obtained through the process of controlled granulation process results in unique particle size distribution. The raw materials are composed primarily of low calcium silicate based mineral additives.
Its latent hydraulic property and pozzolanic reactivity results in an enhanced hydration process. Addition of G-FINE improves the packing density of the paste component. In spite of its high fineness the results are in lowering water demand, admixture dosage and hence improving strength and durability parameters of concrete at all ages.
G-FINETM are observed in the concrete mix design, the initial rate of strength development was found to be increased or similar as other pozzolanic materials.
Application
Roads, Residential, Commercial structures
Producing mass concrete for raft and pile foundations
Low water to binder rations for high performance concrete
Better retention of workability and faster initial strength gain
High Strength construction work in low or high temperature weather
Benefits
Increase compressive strength ,permeability, workability of concrete
Improves the durability of concrete
It can be used in waterproofing as an additive
It can decrease the heat of hydration
Resistance against saltwater & chemicals
Non-Toxic, Eco friendly
Cost effective, economical solution DOSAGE These goals are accomplished using cement pastes, mortars, and concretes with water-Cementitious material ratios ranging from dosage: 5% to 10% .The segregation of cement paste is caused by high super plasticizer dosages that do not cause segregation of concrete with the same water-Cementitious material ratio. Concrete containing G-FINETMas a partial replacement for cement exhibits an increased compressive strength because of the improved strength of its cement paste constituent. Changes in the paste-aggregate interface caused by silica fume appear to have little effect on the uniaxial compressive strength of concrete
PACKAGINGS G-FINE shall be packed and supplied in 25 Kg plastic bags/Customized packing is done if required in G-Fine brand. It is also available in Bulk Jumbo bags. STORAGE G-FINE when stored correctly has an indefinite shelf life. Like cement,G-FINE must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.SAFETY INFORMATION / DECLARATION
Extensive testing has shown G-FINE to be non-toxic and environmentally friendly. No known significant health risks are associated with G-FINE but high concentrations of dust may cause irritation. It is recommended that suitable Protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice. The following information has been obtained from test results in an accredited l
INCEPTION: G- GROUT MF-8 is highly fluid, single component, cementitious grout pre packed .
G-GROUT MF-8 powder It is manufactured by unique PSD technology to facilitate easy to inject and effective deep fine cracks, pores and voids. It has much finer particle size than other hydraulically setting materials. It is produced in state of art manufacturing plants in a controlled environment resulting in excellent filling quality.
PURPOSE: G- GROUT MF-8 is suitable for injecting and grouting in rock, soil, concrete and masonry and for filling joints, cracks and holes. �·MF-8 can be used at vertical and horizontal surfaces working. MF-8 is a ready-to-use dry-blend mortar based on cement modified with organic additives, which hardens without shrinkage when mixed with water
BENEFITS: G-GROUT MF-8 can be injected with standard cement grouting equipment
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards
Eco friendly & Cost Effective.
TECHNICAL SPECIFICATION
METHODS OF USES: Pre-process-
The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
Mixing:
MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes. Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
PACKAGING G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
STORAGE G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo. Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25C, protected from heat, frost and direct sunlight. SAFETY INFORMATION Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice
G FINE is a new generation supplementary cementitious material (SCM) with a built-in high tech content. In spite of its high fineness it does not increase water demand at the dosage range of 5 to 15 percent of normal OPC in general. In fact concrete slump is seen to be improved, due to the dense packing of cementitious material, producing low void content. The use of G FINE results in hydrated cement matrix to comprise of very small pores.
G FINE is a specially processed product based on high glass content with high reactivity obtained through the process of controlled granulation. The raw materials are composed primary of low calcium silicates. The processing with other select ingredients results in controlled particle size distribution. G FINE can also be used as a high range water reducer to improve compressive strength or as a super workability aid to improve flow.
G FINE can be used as practical substitute for Silica Fume as per the results obtained. If the advantages of G FINE are observed in the concrete mix design, the initial rate of strength development was found to be increased or similar as that of Silica Fume.
Where to use G FINE :
Residential, roads, airports, commercial building. Producing mass concrete structures and pile. In high-rise structures the concrete is to be pump easily. Low water to binder ration for high performance concrete. Precast concrete element for heavy structures precast units. To improved initial strength and increase faster . Better retention of workability and improved strength gain.
Benefits of G FINE :
The workability of the mix retention is improved Improve durability and permeability of concrete Increased strength of concrete Reduction in segregation can be observed in the mix Reduction in heat of hydration of the mix Non- toxic , eco friendly cost effective, economical solution
G-FINE
Packaging:
G FINE is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25kg plastic lined bags.
Storage:
G FINE when stored correctly has an indefinite shelf life. Like cement, G-FINE must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo Or werehouse .
Health and Safety:
Extensive testing has shown G FINE to be non-toxic and environmentally benign. No known significant health risks are associated with G FINE but high concentrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
Important Notice:
GURU CORPORATION products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the Supply of Goods and Service.
G-GROUT UF-9 is professional grade material that used as crack injection grout powder. It has finer particle size. It is produced in well known manufacturing plant in a controlled environment resulting in consistent quality. It is manufactured by unique particle size distribution technique to enable finest particle size for application.
Purpose
Fixing ground anchors for sheet pile walls, concrete pile walls, retaining walls tunnels etc.
Defects on building masonry or pavement.
Filling the void between the lining and rock face in tunnel work.
Injection grouting of joints in masonry structures, restoration of heritage structures, dams, etc.
Benefits
G-GROUT UF-9 can be injected with standard cement grouting equipment
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards
Eco friendly
Benefit in cost.
Stoage
G-GROUT UF-9 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
HEALTH AND SAFETY
Extensive testing has shown G-GROUT UF-9 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT UF-9 but high concentrations of dust may cause irritation. It is recommended that suitable protective clothing, gloves and eye/face protection is worn. In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
Packing
G-GROUT UF-9 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25kg plastic lined bags.
Maxxcon RM is a high performance, polymer modified repair mortar designed for restoring damaged, cracked or spalled concrete and plastered wall surfaces. it provides excellent adhesion, workability and strength, making it ideal for structural and non -structural wall repairs. the non - shrinking formulation ensures durable, crack - free repairs with a smooth finish suitable for painting or protective coatings.
Areas of Application
Spalled / damaged wall surfaces
Cracks and voids in plaster & concrete walls
Honeycombs and surface defects
Internal & External repairs
Features & Benefits
1) Polymer modified formula - Excellent adhesion to concrete & plaster
2) Non - Shrinking repair mortar - prevents secondary cracking
3) High compressive & flexural strength - durable, long - term repair
4) Smooth workable consistency - easy to apply & finish
5) Reduced rebound & wastage - economical application
6) Paint able after curing - ready for decorative finishes
GFRP rebar is made of high-strength glass fibers along with a highly durable resin. These
products are developed as a superior alternative to steel in concrete reinforcement. It is
widely used to reinforcing concrete in applications where it is exposed to water, salt water
or chemical environments
- Typical Advantages:
- Non-Corrosive â?? It will not corrode when exposed to a wide variety of corrosive substances
- including chlorides
- High Strength-to-Weight Ratio â?? best reinforcement for weight sensitive reinforcement
- Non-Conductiveâ?? It is excellent electrical and thermal insulator
- Excellent Fatigue Resistanceâ?? performs best in cyclic loading solutions
- Impact Resistanceâ?? It resists sudden and severe point loading
- Magnetic Resistance â?? completely non-effective to electromagnetic fields; excellent for
use in electromagnetic testing facilities
- Light Weight easy to transport, no need for lifting equipment, easy to handle
