Find Verified White Cement Suppliers, Manufacturers and Wholesalers

Product Code Product Description

PRS-CM00020 High Pressure Cement Autoclave, 230 V 50-60 Hz

STANDARDS : ASTM C151, C490; UNE 7207

The PRS-CM00020 High Pressure Cement Autoclave is designed to perform expansion tests on cement specimens.10 specimens can simultaneously be tested in the high pressure steam vessel of 154 mm diameter and 430 mm height.

The Autoclave consists of a pressure gauge, pressure regulator, temperature regülatör, control switches and safety valve.

PRS-CM0033 Two Gang Shrinkage mould should be ordered separately.

The High Pressure Cement Autoclave is supplied complete with;
Specimen Rack, 10 samples capacity

Dimensions 450x475x1080 mm
Weight (approx.) 55 kg
Power 2600 W

Product Code Product Description

PRS-CM0037 Digital Length Comparator

PRS-CM0038 Length Comparator with Length Measuring Sensor and Digital Readout Unit

STANDARDS : EN 1367â??4, 12617â??4, 12808-4; ASTM C151, C157, C227, C311, C341, C342, C441,C452, C490, C531, C596, C806, C878; BS 1881:5, 6073

Length Comparators are used to determine the length changes on different type of cement prisms.

The set consists of a length measuring frame with measuring device attached to it.

There are 2 models available; PRS-CM0037 is with 0.001 mm x 12,7 mm digital dial gauge (PRS-CM0152) and PRS-CM0038 is with special 0.0001 mm x 30 mm transducer and readout unit.

Reference rod and moulds should be ordered separately according to test to perform.

Product Code Dimensions Weight

PRS-CM0037 180x180x450 mm 6 kg

PRS-CM0038 250x250x650 mm 8 kg

Product Code Product Description

PRS-CM0029 Three Gang Shrinkage Mould 40x40x160 mm, EN

PRS-CM0030 Steel Insert 40x40x160 mm for PRS-CM0029, 18 pieces/pack

PRS-CM0031 Reference Rod 160 mm Long with Convex Hemispherical End

PRS-CM0032 Tamper, Hardwood 38x15x200mm, 250 g, EN

PRS-CM0033 Two Gang Shrinkage Mould 25x25x285 mm, ASTM

PRS-CM0034 Steel Insert 25x25x285 mm for PRS-CM0033, 12 pieces/pack

PRS-CM0035 Reference Rod 295 mm Long with Convex Hemispherical End

STANDARDS : ASTM C151, C157, C452, C490, C596; EN 12617-4

The PRS-CM0029 , PRS-CM0033 Three and Two Gang Shrinkage Moulds are used for the determination of linear shrinkage/expansion of cement mortar when used together with the PARSROS Length Comparator (PRS-CM0037 or PRS-CM0038 ).
Reference Rod should be ordered separately.

Product Code PRS-CM0029 PRS-CM0033

Dimensions 300x190x70 mm 90x340x40 mm

Weight (approx.) 12 kg 4 kg

Product Code Product Description

PRS-CM6700 250 kN Cement Compression Frame

PRS-CM6710 15/250 kN Cement Flexure/Compression Frame

STANDARDS : EN 196-1, 459-2, 1015-11, 13454-2; ASTM C109, C348, C349;BS 3892-1, 4551-1

The PRS-CM6700 and PRS-CM6710 , very rigid two column frames have been designed for compression and/or flexure testing of mortar prisms and cubes specimens. Load cells are used on both frames to provide high accuracy in load measuring. Both frames are fitted with round platens with 165 mm diameter and these should be used together with suitable flexure and compression devices.

Distance pieces and transparent front-rear safety doors (should be factory insttalled ) should be ordered separately.


Distance Pieces for Frame

Due to the modular design of the frames any sample with suitable size, load and pace rate can be test on both chambers by decreasing the distance between platens.
Distance Pieces

PRS-CM4630 Distance piece dia. 165 mm x 15 mm
PRS-CM4631 Distance piece dia. 165 mm x 30 mm
PRS-CM4633 Distance piece dia. 165 mm x 50 mm
PRS-CM4634 Distance piece dia. 165 mm x 90 mm

Platens

PRS-CM0116 Upper Loading Platen with Ball Seating Assembly Ã?:165 mm and Lower Loading Platen, Ã?:165 mm

Manufactured from high quality steel are hardened (more than HRC 53), smoothed and finished.

The roughness value for the surface texture of machine and auxiliary platens are 3.2 μm.

Loading Cylinder Assembly & Limit Switch

All frames have a single acting up stroking ram. The diameter of piston changes with regard to the capacity.
The maximum ram stroke is 50 mm, a limit switch is fitted to prevent over travel of the ram which cuts the power to the pump.
There is a low friction coaxial PTFE seal between the cylinder and the piston fitted to the cylinder.

Accessories

PRS-CM0120/A Flexure Jig Assembly to test 40x40x160 mm mortar prisms, ASTM

PRS-CM0120/E Flexure Jig Assembly to test 40x40x160 mm mortar prisms, EN

PRS-CM0121/A Compression Jig Assembly to test 50 mm (2â?�) mortar cubes, ASTM

PRS-CM0121/E Compression Jig Assembly to test portions of 40x40x160 mm mortar prisms, EN

Product Code Product Description

PRS-CM0069 Bulk Density Apparatus

STANDARDS : EN 459-2

The bulk density of lime is of interest for storage and packaging and for determining volume and capacity of mixing equipment necessary for processing the material.

The PRS-CM0069 Bulk Density Apparatus is designed to determine bulk density by allowing a sample to fall from a known height into a volumetric container.

The apparatus consists of a hopper, 1 liter capacity cylindrical container and a spring-loaded trap.

Dimensions 250x250x750 mm

Weight (approx.) 2 kg

Product Code Product Description

PRS-CM0074 Cement Wet Sieving Apparatus

STANDARDS : EN 451-2

The PRS-CM0074 Wet Sieving Apparatus is used for determining the fineness of fly ash. The apparatus comprises of a special stainless steel sieve, 0.045 mm opening, a spray nozzle Ã? 17.5 mm with 17 holes Ã? 0.5 mm oriented and spaced to conform to the standards.

Supplied complete with a pressure gauge Ã? 80 mm and fittings for connection to the water supply.

Dimensions 250x150x150 mm
Weight (approx.) 2 kg

Product Code Product Description

PRS-CM6331 250 kN Automatic Cement Compression Testing Machine 220-240 V 50-60 Hz

PRS-CM6331 /110 250 kN Automatic Cement Compression Testing Machine 110 V 60 Hz

PRS-CM6431 15/250 kN Automatic Cement Flexure/Compression Testing Machine 220-240 V 50-60 Hz

PRS-CM6431 /110 15/250 kN Automatic Cement Flexure/Compression Testing Machine 110 V 60 Hz

PRS-CM0116 Upper Loading Platen with Ball Seating Assembly Ã?:165 mm and Lower Loading Platen, Ã?:165 mm

PRS-CM0120/A Flexure Jig Assembly to test 40x40x160 mm mortar prisms,ASTM

PRS-CM0120/E Flexure Jig Assembly to test 40x40x160 mm mortar prisms, EN

PRS-CM0121/A Compression Jig Assembly to test 50 mm (2â?�) mortar cubes, ASTM

PRS-CM0121/E Compression Jig Assembly to test portions of 40x40x160 mm mortar prisms, EN

PRS-CM0122 Compression Jig Assembly BS, to test 70,7 mm mortar cubes

STANDARDS : EN 196-1, 459-2, 1015-11, 13454-2; ASTM C109, C348, C349; BS 3892-1, 4551-1

The PARSROS Automatic range of single testing chamber and double testing chamber compression and flexure testing machines have been designed for reliable and consistent testing of mortar samples. These compression and flexure testers are the results of continuous applications and research studies to upgrade the machines with the latest technologies and conform the current standards EN 196-1, 459-2, 1015-11, 13454- 2; ASTM C 109, C348, C349 and BS 3892-1, 4551-1 in terms of its technical properties taking into account client requirements by using suitable accessories. These machines also meet the requirements of CE norms for safety and health of the operator.

Compression and flexture jigs, distance pieces, and also removable transparent front-rear safety doors (should be factory installed) should be ordered separately.

The PARSROS automatic cement compression and flexure testing machines allow less experienced operators to perform the tests. Once the machine has been switched on and the specimen is positioned and centered by the help of centering apparatus. The only required operations are;

â?¢ Setting test parameters, including pace rate (only required when the specimen type is changed.)
â?¢ Choosing the compression or flexure frame by using the changeover valve.
â?¢ Pressing the START button on the control unit.
â?¢ The machine automatically starts the rapid approach; switches the test speed after 1% of the load capacity of the machine and stops once the specimen failure.
â?¢ Automatically saves the test parameters and test results.

The PARSROS automatic cement compression and flexure testing machines consist of very rigid two column single or double chamber frames, automatic hydraulic power pack with data acquisition and control system

Automatic Cement Compression & Flexure Testing Machines

Product Code Product Description

PRS-CM6331 250 kN Automatic Cement Compression Testing Machine 220-240 V 50-60 Hz

PRS-CM6331 /110 250 kN Automatic Cement Compression Testing Machine 110 V 60 Hz

PRS-CM6431 15/250 kN Automatic Cement Flexure/Compression Testing Machine 220-240 V 50-60 Hz

PRS-CM6431 /110 15/250 kN Automatic Cement Flexure/Compression Testing Machine 110 V 60 Hz

PRS-CM0116 Upper Loading Platen with Ball Seating Assembly Ã?:165 mm and Lower Loading Platen, Ã?:165 mm

PRS-CM0120/A Flexure Jig Assembly to test 40x40x160 mm mortar prisms,ASTM

PRS-CM0120/E Flexure Jig Assembly to test 40x40x160 mm mortar prisms, EN

PRS-CM0121/A Compression Jig Assembly to test 50 mm (2â?�) mortar cubes, ASTM

PRS-CM0121/E Compression Jig Assembly to test portions of 40x40x160 mm mortar prisms, EN

PRS-CM0122 Compression Jig Assembly BS, to test 70,7 mm mortar cubes

STANDARDS : EN 196-1, 459-2, 1015-11, 13454-2; ASTM C109, C348, C349; BS 3892-1, 4551-1

The PARSROS Automatic range of single testing chamber and double testing chamber compression and flexure testing machines have been designed for reliable and consistent testing of mortar samples. These compression and flexure testers are the results of continuous applications and research studies to upgrade the machines with the latest technologies and conform the current standards EN 196-1, 459-2, 1015-11, 13454- 2; ASTM C 109, C348, C349 and BS 3892-1, 4551-1 in terms of its technical properties taking into account client requirements by using suitable accessories. These machines also meet the requirements of CE norms for safety and health of the operator.

Compression and flexture jigs, distance pieces, and also removable transparent front-rear safety doors (should be factory installed) should be ordered separately.

The PARSROS automatic cement compression and flexure testing machines allow less experienced operators to perform the tests. Once the machine has been switched on and the specimen is positioned and centered by the help of centering apparatus. The only required operations are;

Setting test parameters, including pace rate (only required when the specimen type is changed.)

Choosing the compression or flexure frame by using the changeover valve.
Pressing the START button on the control unit.

The machine automatically starts the rapid approach; switches the test speed after 1% of the load capacity of the machine and stops once the specimen failure.
Automatically saves the test parameters and test results.

The PARSROS automatic cement compression and flexure testing machines consist of very rigid two column single or double chamber frames, automatic hydraulic power pack with data acquisition and control system

Criteria RKB Gr.1 RKB Gr.2 RKB Gr.3 RKB Gr.4
Foreign Matter 0.2%Max 0.5%Max 1%Max 1.5%Max
Contrasting Seed 0.2%Max 0.5%Max 1%Max 2%Max
Under Size Seed 1.5%Max 3%Max 4%Max 5%Max
Weevilled Seeds 2%Max 3%Max 5%Max 8%Max
Badly Damaged Beans 1.5 3 4 5
Split Seed 2% 3% 5% 8%
Broken 2.5%Max 3.5%Max 5%Max 8%Max
Moisture Content 14%Max 14%Max 14%Max 14%Max
Impurities 6.2%Max 10%Max 15%Max 22.5%Max
Purity 93.8% 90% 85% 77.5%


Red Kidney Beans
50kg P.P. Bags
Loaded in 20'FCL

Gold Bathroom Standard Series
Tria 80 White

Ceramic Washbasin, Lacquer Painted Covers
Tall Cabinet
Mirror Unit

Tria 80 cm Bathroom Cabinet Dimensions

Sink Unit:
Width: 80cm
Height: 50 cm (The height from the floor to the top of the cabinet is 83 cm)
Depth: 46 cm

Mirror Unit:
Width: 80cm
Height: 70cm
Depth: 16 cm

Tall Cabinet Unit:
Width: 38cm
Height: 139 cm (The height from the floor to the top of the tall unit is 179 cm)
Depth: 32 cm

Gold Ban-Yom Premium Series
Lacia 80 White

Lacia 80 cm White Bathroom Furniture
Relief Patterned Covers, Lacquer Paint
Ceramic Sink
Relief Patterned Mirror

Lacia 80 cm Bathroom Cabinet Dimensions

Sink Unit:
Width: 80cm
Height: 49.5cm
Depth: 45 cm

Mirror Unit:
Width: 80cm
Height: 69cm
Depth: 16 cm

Gold Ban-Yom Premium Series
Elsa 80 White

Elsa 80 cm White Bathroom Furniture
Ceramic Sink, Lacquer Paint
Useful Tall Cabinet
LED Illuminated Mirror Unit

Elsa 80 cm Bathroom Cabinet Dimensions

Sink Unit:
Width: 80cm
Height: 57.5cm
Depth: 54.5 cm

Mirror Unit:
Width: 60cm
Height: 90cm
Depth: 5cm

Tall Cabinet Unit:
Width: 38cm
Height: 140cm
Depth: 32 cm

Gold Ban-Yom Premium Series
Vadenda 80 White

Vadenda 80 cm White Bathroom Furniture

Ceramic Sink:
Vadenda 80 offers a sparkling look to your bathrooms with its ceramic washbasin made of 1st class quality ceramic material compatible with its body.

Geometric Patterns:
Vadenda 80 will add elegance to your bathrooms with its geometric patterned washbasin unit, mirror unit and tall cabinet unit.

LED Illuminated Mirror:
Vadenda 80 brings a perfect harmony to your bathrooms with its LED illuminated smoked mirror unit.

Vedenda 80 cm Bathroom Cabinet Dimensions

Sink Unit:
Width: 76cm
Height: 82cm
Depth: 46 cm

Mirror Unit:
Width: 79 cm
Height: 89cm
Depth: 12.5 cm

Tall Cabinet Unit:
Width: 45cm
Height: 141cm
Depth: 32 cm

Gold Ban-Yom Exclusive Series
Blanc 70 White

Ceramic Sink, Lacquer Paint
Lacquered Mirror Unit

Blanc 70 cm Bathroom Cabinet Dimensions

Sink Unit:
Width: 70cm
Height: 85cm
Depth: 48.5 cm

Mirror Unit:
Width: 65cm
Height: 80 cm (The height from the floor to the top of the mirror unit is 193 cm)
Depth: 5cm

Gold Ban-Yom Exclusive Series
Blanc 110 White

Ceramic Sink, Lacquer Paint
Lacquered Mirror and Shelf Unit

Blanc 110 cm Bathroom Cabinet Dimensions

Sink Unit:
Width: 110cm
Height: 85cm
Depth: 48.5 cm

Mirror Unit:
Width: 65cm
Height: 80 cm (The height from the floor to the top of the mirror unit is 193 cm)
Depth: 5cm

Shelf Unit:
Width: 30cm
Height: 71.5 cm (193 cm from floor to top of mirror unit)
Depth: 25cm

Gold Ban-Yom Exclusive Series
Hermes 100 White

Ceramic Sink, Lacquer Paint
LED Illuminated Touch Mirror Unit

Hermes 100 cm Bathroom Cabinet Dimensions:

Sink Unit:

Width: 100cm
Height: 83cm
Depth: 46 cm

Mirror Unit:

Width: 70cm
Height: 90cm
Depth: 5cm

Gold Ban-Yom Exclusive Series
Armani 110

Ceramic Sink, Lacquer Paint
Tall Cabinet
LED Illuminated Mirror Unit

Armani 110 cm Bathroom Cabinet Dimensions:

Sink Unit:
Width: 110cm
Height: 55 cm (The height from the floor to the top of the cabinet is 83 cm)
Depth: 46 cm

Mirror Unit:
Width: 85cm
Height: 85cm
Depth: 5cm

Tall Cabinet Unit:
Width: 45cm
Height: 140 cm (The height from the floor to the top of the tall unit is 179 cm)
Depth: 32 cm

Gold Ban-Yom Exclusive Series
Ricci 105 Matte White

Ceramic Sink, Lacquer Paint
LED Illuminated Touch Mirror Unit

Ricci 105 cm Bathroom Cabinet Dimensions

Sink Unit:
Width: 105cm
Height: 83cm
Depth: 48 cm

Mirror Unit:
Width: 85cm
Height: 85 cm (The height from the floor to the top of the mirror unit is 193 cm)
Depth: 5cm

Gold Ban-Yom Premium Series
Vela 120 High Glosy White

Bringing ideal solutions to the needs of comfort, aesthetics and functionality, â??Velaâ?? offers bathrooms an ambiance suitable for modern lifestyles with its flexible usage options.

Vela 120 cm Bathroom Furniture

Open Shelving Unit:
Vela 120 will add a different atmosphere to your bathrooms with its open shelving unit and black color band that adorns its double-door structure.

Ceramic Washbasin, High Glosy White Color:
Vela 120 offers a sparkling look to your bathrooms with its ceramic washbasin made of 1st class quality ceramic material compatible with its body.

Double Mirror and Shelf Unit:
With its open shelf unit, Vela 120 will be the reason for your preference with its stylishness and aesthetics as well as its useful structure.

Vela 120 cm Bathroom Cabinet Dimensions

Sink Unit:
Width: 120cm
Height: 49cm
Depth: 45 cm

Mirror Unit:
Width: 120cm
Height: 68cm
Depth: 15.5 cm

Product Code Product Description

PRS-CM0075 Manuel Mortar Mixer, 220-240 V 50-60 Hz

PRS-CM0075/110 Manuel Mortar Mixer, 110 V 60 Hz

PRS-CM0076 Spare Bowl for PRS-CM0075 and PRS-CM0085, 5 L

PRS-CM0078 Spare Beater for PRS-CM0075 and PRS-CM0085

STANDARDS : EN 196-1, 196-3, 413-2, 459-2, 480-1, 1015-2, 12617-4; ASTM C187, C305, AASHTO T129, T131, T162

The PRS-CM0075 Manual Mortar Mixer has a 5 liter (approx.) capacity, it has been designed to mix mortars and cement pastes primarily to the requirements of standards.

The mixing paddle revolves at a rate of 140 rpm. with a planetary motion of 62 rpm. in low speed. In high speed, the paddle revolves at the rate of 285 rpm. with a planetary motion of 125 rpm. The user can choose the speeds easily by using the switch fitted to the machine.

There is a sand filling apparatus on the mixer to pour sand easily. The bowl and beater are easily fitted and removed from mixer.

The Manual Mortar Mixer is supplied complete with;
â?¢ Bowl, 5 L (approx.)
â?¢ Beater

Dimensions 300x555x610 mm

Weight (approx.) 54 kg

Power 200 W

Product Code Product Description

PRS-CM0090 Jolting Table, EN, 220-240 V 50 Hz, (60 Hz version is available upon request)

PRS-CM0091 Jolting Table with Soundproof Safety Cabinet, EN, 220-240 V 50 Hz

PRS-CM0092 Three Gang Mould for 40x40x160 mm

PRS-CM0093 Feed Hopper 40x40x160 mm for PRS-CM0092

PRS-CM0094 Short and Long Spreaders and Straightedge, for PRS-CM0092

STANDARDS : EN 196-1; ISO 679
Jolting Table is used for compacting of cement specimens in 40x40x160 mm mould and consists of mould table seated on a rotating cam driven at 60 r.p.m. The falling height is 15 mm conforming to EN 196-1. The machine is equipped with a counter which provides automatic shut off at end of preset drop numbers.

Weight and dimensions of the jolting table fully comply with the requirements of EN 196-1 standard. When used with PRS-CM0092 Three Gang Mould and PRS-CM0093 Feed Hopper, the total weight of the moving part is 20 kg ± 0.5 kg. Without PRS-CM0092 and PRS-CM0093 the weight of the moving parts is 6.85 kg. Rapid mould lock and release system allows easy and quick operation.

The supporting frame of the machine has been designed to ensure precise dimensions, table flatness, correct centering of the three gang mould on the table.

The motor and gearbox assembly is enclosed in a protective housing, which promotes user safety (the moving parts are inaccessible) and long life for the gearbox.

The standard model can be supplied with a safety/noise reduction cabinet. The cabinet is lined internally with soundproofing material to reduce sound level conforming to CE directives.

PRS-CM0093 Feed Hopper is used for filling PRS-CM0092 Three Gang Moulds placed on the Jolting Table.

PRS-CM0092 Three Gang Mould, PRS-CM0093 Feed Hopper, PRS-CM0094 Short and Long Spreaders and Straightedge should be ordered separately.

Product Code PRS-CM0090 PRS-CM0091

Dimensions 1050x350x500 mm 1440Ã?500Ã?575 mm

Weight (approx.) 55 kg 125 kg

Motor Speed 60 r.p.m

Drop Height 15 mm

Power 250 W

Air Entrainment Meter for Mortar

Product Code Product Description

PRS-CM0066 Air Entrainment Meter for Mortar 1 lt.

STANDARDS : EN 413-2, 459-2, 1015-7

The PRS-CM0066 Air Entrainment Meter for Mortar is used for determining the air content of cement paste, cement mortar and lime mortar. The air entrainment meter is manufactured from cast aluminum, the upper part and the lower test pot are held together with an air-tight seal which are easily adjusted by using the two spring clamps.

The pressure gauge is installed in the head of the meter and the scale works in the 0-20 volumetric % range. The air is compressed with a hand pump installed in the system and the smart configuration of the test and correction buttons enables fast and simple testing.

Dimensions 200x200x320 mm
Weight (approx.) 3,5 kg

Product Code Product Description

PRS-CM0098Vibrating Machine for 70.7 mm Cube Moulds, BS, 220-240 V 50 Hz

STANDARDS : BS 4550

The PRS-CM0098 Vibrating Machine is used for the preparation and compaction of 70.7 mm mortar cube specimens.

The mould table is mounted on four springs attached to an eccentric shaft which allows each sample to be vibrated at 12000 cycles per minute. There is a timer on it to preset time and it stops automatically in every 120 seconds.

60 Hz version should be mentioned on order if required.
70.7 mm cube mould (PRS-CM0096) should be ordered separately.

Dimensions450x650x850 mm

Weight (approx.)80 kg

Eccentric Shaft Rotation12000 r.p.m

Power1100 W

Product Code Product Description

PRS- CM0065 Plunger Penetration Apparatus

STANDARDS : EN 413-2, 459-2, 1015-4

Plunger Penetration Apparatus is used to determine the consistency of fresh mortar, building lime and masonry cement. The test apparatus consists of a base to place the test cup and a vertical column holding the penetration plunger assembly.

The drop default height is adjusted to 100 mm. The plunger assembly weight is 90 g.

The Plunger Penetration Apparatus is supplied complete with;

Test cup, Ã? 80 mm x 70 mm

Tamper

Dimensions 200x200x600 mm

Weight (approx.) 6 kg

Product Code Product Description

PRS-CETLS025 Lever Support

STANDARDS : EN 13294,TS EN 1015-9
Lever supported(Drill-Holder Type)
It is complete with washer and penetration rod brass made, clamp and locking support.
The machine is used for the determination of processing and rectifying of fresh mortarâ??s duration.
Dimensions 380 x 300 x (h)500 mm
Weight (approx.) 12 kg

Product Code Product Description

PRS-CM0073 Mud Balance

The PRS-CM0073 Mud Balance, an ideal equipment for site applications, provides an accurate and easy method for determining the mud density. The accuracy of the readings is not affected by the temperature of the drilling mud.

The equipment consists of a base and a graduated arm with an integral spirit level, counter weight, cup, lid, rider, knife-edge. Supplied with a special plastic carrying case which can be used to stabilize the equipment at the working position.

Dimensions 550x110x100 mm

Weight (approx.) 1 kg

Product Code Product Description

PRS-CM0058 Gillimore Apparatus

STANDARDS : ASTM C91, C141, C150, C266; AASHTO T154

The PRS-CM0058 Gillmore Apparatus is used to determine the setting time of cement hydraulic hydrometer lime and mortar. Apparatus consists of two horizontally positioned arms, carrying weighted needles, initial needle has a 2.12 mm diameter and 113.4 g in weight and the final needle has a 1.06 mm diameter and 453.6 g in weight.

Dimensions 300x100x300 mm
Weight (approx.) 2,5 kg

Product Code Product Description

PRS-CM0100 Curing Cabinet 750 L, 220-240 V 50-60 Hz

STANDARDS : EN 196-1; ISO 679

The PRS-CM0100 Curing Cabinet is used for curing of cement, concrete cubes or other mortar specimens. It can be used for curing cement specimens within the mould, or after removing from the mould.

The curing cabinet provides 20 ± 1°C temp. and over 95% RH humidity for cement specimens. Internal chamber and racks are made of stainless steel. The temperature is maintained at 20 ± 1°C by a immersion heater and refrigerator unit which are supplied complete with cabinet. The cabinet is equipped with a digital control unit which controls and monitors the temperature.

The humidity is maintained from 95% to saturation by water nebulizers and is also monitored on the digital control unit.

Internal Dimension 900x700x1350 mm
External Dimension 1100x1000x2200 mm
Weight (approx.) 150 kg
Power 1200 W

Product Code Product Description

PRS-CM1462 Muffle Furnace 5 lt. 1200°C Max. Temperature with Programmable Timer, 20-240 V 50-60 Hz

STANDARDS : EN 196-2; ASTM C25, C115

PRS-CM1462 Muffle Furnace is used for determining the loss on ignition and insoluble residue of cement and building lime.

Working temprature and time can be programmed with PID digital control system.

Digital Thermometer Features

Temperature Controller PC 442/2

Max. Temperature 1200 °C

Max. Continuous Temperature 1150 °C

Temperature Deviation at Set Point ± 2°C

Heat Up Time to Max. Temperature 50. min

Internal Volume 5 L

Phase 1

Internal Dimension 140x180x200 mm

External Dimension 650x550x580 mm

Weight (approx.) 56 kg

Power 2000 W

Product Code Product Description

PRSD-1450 Muffle Furnace 3 lt. 1000°C, 220-240 V 50-60 Hz

PRSD-1455 Muffle Furnace 6 lt. 1100°C, 220-240 V 50-60 Hz

PRSD-1460 Muffle Furnace 5 lt. 1200°C, 220-240 V 50-60 Hz

PRSD-1462 Muffle Furnace 5 lt. 1200°C Programmable Timer, 220-240 V 50-60 Hz

PRSD-1465 Muffle Furnace 5 lt. 1600°C, 380 V 50 Hz

The PRSD Series Muffle Furnaces are widely used for determining various properties of construction materials, and they cover a temperature range from 1100°C to 1600°C, they are all front loading for easy operation and are of a double skin construction to maintain a cool outer case. Up to 1300°C, open wire based models are also produced.

Excellent temperature control is provided by a PID digital control system. A vertical counter balanced door keeps the hot insulation away from the operator which opens in an upward movement. The Furnace has a safety switch which isolates the power when the door is opened.

Product Code Product Description

PRS-CM0003 Le Chatelier Flask

STANDARDS : EN 196-6, 450-1, 15617-1; ASTM C110, C128, C188; C989; AASHTO T133

The PRS-CM0003 Le Chatelier Flask is used to determine the density of hydraulic cement, ground granulated blast-furnace slag and fly ash for concrete, filler aggregates and lime.The glass flask has a 250ml capacity. The neck is graduated from 0 to 1 ml and from 18 to 24 mL in 0.1-mL graduations.

Dimensions 100x100x300 mm

Weight (approx.) 0.1 kg

Product Code Product Description

PRS-CM0010 Le Chatelier Mould

PRS-CM0014 Le Chatelier Soundness Kit

STANDARDS : EN 196-3, 450-1, 459-2; EN ISO 9597

The soundness of cement, fly ash for concrete and lime is determined by using the Le Chatelier moulds and Le Chatelier Water Bath (PRS-CM0016) according to the relevant standard.

The Le Chatelier Soundness Kit is supplied complete with;
Le Chatelier moulds 3 pcs.
50x50 mm glass plates 6 pcs.
300 gr Weights 1 pcs.
100 gr Weight, 3 pcs.
Tamping Rod 17 mm dia. x 70 gr
Steel Ruler
Plastic Carrying Case

Dimensions 340x290x80 mm

Weight (approx.) 2 kg

Product Code Product Description

PRS-CM0040 Blaine Air Permeability Apparatus

PRS-CM0041 U Manometer Tube

PRS-CM0042 Manometer Liquid 250 ml

PRS-CM0043 Cell with Perforated Disc and Plunger

PRS-CM0044 Filter Paper 100 pcs.

PRS-CM0045 Filter Paper 1000 pcs.

PRS-CM0046 Reference Cement 5 g, ASTM

STANDARDS : EN 196-6; ASTM C204; AASHTO T153

The PRS-CM0040 Blaine Air Permeability Apparatus is used to determine the fineness of Portland cement, limes and similar powders expressed in terms of their specific surface. The apparatus is supplied complete with a U manometer tube, manometer liquid, glass connection parts, test stand, rubber aspirator, cell with perforated disc and plunger, plastic funnel and 100 pieces of filter paper.

PRS-CM0046 Reference Cement should be ordered separately.

The Blaine Air Permeability Apparatus is supplied complete with;
â?¢ U Manometer Tube
â?¢ Manometer Liquid, 250 ml
â?¢ Test Stand
â?¢ Rubber Aspirator
â?¢ Cell with Perforated Disc and Plunger Plastic Funnel
â?¢ Filter Paper, 100 pcs.

Dimensions 300x540x210 mm (packed)

Weight (approx.) 7 kg (packed)

Product Code Product Description

PRS-A0440 Efflux Index Apparatus (Flow Coefficient of Fine Aggregates), EN

PRS-A0440 Efflux Index (Flow Coefficient of Fine Aggregates) Apparatus is used to obtain information about the shape and the angularity of grains of fine aggregates.

The flow coefficient of an aggregate is the time, expressed in seconds, for a specified volume of aggregate to flow through a given opening, under specified conditions using a standard apparatus.

Efflux Index (Flow Coefficient of Fine Aggregates) Apparatus consist of two funnels with different opening, cylindrical hopper, metal stand with a shutter and metal container.

Dimensions 150x180x410 mm

Weight (approx.) 5 kg

Product Code Product Description

PRS-CM0070 Slaking Vessel

STANDARDS : EN 459-2

PRS-CM0070 Slaking Vessel is used to determine the yield of lime by leaving the lime sample to slake into. Stainless steel made and double walled insulated. The cylinder has inside dimensions dia. 113 mm by 140 mm deep. Supplied complete with cover.

Dimensions 120x120x160 mm
Weight (approx.) 4 kg

PRSCM-0037 Digital Length Comparator

PRSCM-0038 Length Comparator with Length Measuring Sensor 220-240 V 50-60 Hz

Length Comparators are used to determine the length changes on different type of cement prisms.

The set consists of a length measuring frame with measuring apparatus attached to it. There are 2 models available; PRSCM-0037 is with 0.001 mm x 12,7 mm digital dial gauge and PRSCM-0038 is with special 0.0001 mm x 30 mm transducer and readout unit.
Reference rod and moulds should be ordered separately according to the test to be performed.

Dimensions

PRSCM-0037 180x180x450 mm

PRSCM-0038 250x250x650 mm

Weight (approx.)

PRSCM-0037 6 kg

PRSCM-0038 8 kg

Cement

Product Code Product Description

PRS-B0510Concrete Flow Table Test Set

PRS-B0512Flow Cone for PRS-B0510

PRS-B0513Wooden Tamper 40x40x335 mm

The test set is used for concrete mixes of high workability and determines flow index as an arithmetic mean of the diameter of the specimen after working on a flow table.

The apparatus consists of a double steel table, an upper table measuring 700x700 mm and hinged at one side to the lower table.

The top table is inscribed and all parts are protected against corrosion. The stainless steel cone has a 130 ±2 mm top diameter, 200 ±2 mm base diameter and 200 ±2 mm height and 1.5 mm thickness.

Dimensions700x850x300 mm

Weight (approx.)40 kg

The Concrete Flow Table is supplied complete with;
â?¢Flow Cone
â?¢Wooden Tamper

Product Code Product Description

PRS-CMA0050 Automatic Vicat Apparatus

STANDARDS : EN 196-3:2005; EN 13279-2 (GYPSUM);EN 480-2 /ASTM C187, ASTM C191

The Vicatronic apparatus, that is designed and manufactured using the most recent and sophisticated technology, is used for the initial and final setting time determination of cements or mortar pastes.Movements along X Y Z axes Up to 30 different test types may be programmed and over 1000 tests may be memorized. PC Port Initial and final setting time (in 0.1 mm) Automatic cleaning of the needle Automatic stop and storage of measurements up to 50 tests.

Plunger for initial consistency Thermostatic baths (optional)

GLCD display for data input and diagram/test report.Printer for final test report and diagram

RS 232 serial port for PC connection Moulds and further needles have to be ordered separately, according to the various standards.

Power supply 220 V, 50 Hz, single phase.

Weight 40 kg.

Product Code Product Description

PRS-CM0050/A Vicat Test Set EN

PRS-CM0050/E Vicat Test Set ASTM

PRS-CM0051 Vicat Apparatus (Frame)

PRS-CM0052/E Vicat Mould EN Base ID 80 mm, Top ID 70 mm, Height 40 mm

PRS-CM0052/A Vicat Mould ASTM Base ID 70 mm, Top ID 60 mm, Height 40 mm

PRS-CM0053/E Initial Vicat Needle EN 1.13 mm dia.

PRS-CM0053/A Vicat Needle ASTM 1 mm dia.

PRS-CM0054 Final Vicat Needle EN 1.13 mm dia.

PRS-CM0055 Consistency Plunger 10 mm dia.

PRS-CM0056 Supporting Glass Plate

PRSTAS-0121 Transfer Dish for PRSTAS -0120 and PRS-CM0050

PRSGT-1305 Glass Thermometer Max. 110°C

PRSC-CM0057 Additiniol Weight, 700 gr, EN 480-2

STANDARDS : EN 196-3, 480-2; ASTM C187, C191; AASHTO T129, T131
The Vicat Test Set is used for the determination of the setting time and consistency of cement by Vicat Method.
PRSTAS -0121 Transfer Dish which is used as a Water Wessel EN, for layering the vicat mould under water.
The Vicat Test Set is supplied complete with;
Vicat Mould
Initial and final Needles (for EN )
Vicat Needle (for ASTM)
Consistency Plunger
Supporting Plate
Glass Thermometer
Transfer Dish (for EN)

Dimensions 150x190x318 mm
Weight (approx.) 3 kg

Bauxite is a sedimentary rock with a relatively high aluminium content. It is the world's main source of aluminium and gallium. Bauxite consists mostly of the aluminium minerals gibbsite (Al(OH)3), boehmite (Y-AlO(OH)) and diaspore (�±-AlO(OH)), mixed with the two iron oxides goethite (FeO(OH)) and haematite (Fe2O3), the aluminium clay mineral kaolinite (Al2Si2O5(OH)4) and small amounts of anatase (TiO2) and ilmenite (FeTiO3 or FeO.TiO2).[1] Bauxite appears dull in luster and is reddish-brown, white, or tan.Bauxite is usually strip mined because it is almost always found near the surface of the terrain, with little or no overburden. As of 2010, approximately 70% to 80% of the world's dry bauxite production is processed first into alumina and then into aluminium by electrolysis.[9] Bauxite rocks are typically classified according to their intended commercial application: metallurgical, abrasive, cement, chemical, and refractory.

Product Code Product Description

PRS-CM0016 Le Chatelier Water Bath, 220-240 V 50-60 Hz

STANDARDS : EN 196-3, 450-1, 459-2; EN ISO 9597

The PRS-CM0016 Le Chatelier Water Bath is used with Le Chatelier moulds for the determination of the soundness of cement paste fly ash for concrete and lime. The internal chamber and the insulated exterior case of the bath are manufactured from stainless steel. The Bath is capable of reaching boiling point in 30 minutes by using two heater units.

There is a timer on the PRS-CM0016 Le Chatelier Water Bath which is used to set the time for reaching the boiling point. After that time the temperature of water is regulated by using one heater unit to conserve energy. Supplied complete with a removable rack to hold up to 10 moulds. A cover is also supplied as standard.
Dimensions 210x470x290 mm
Weight (approx.) 8 kg
Power 1250 W

#Calcium_Chloride 98% (CaCl2) Typical Properties:

TETRA 94 calciumchloride (CaCl2) is a white, high purity pellet with 94 to 97 weight percent CaCl2.

Physical Appearance: White granola

Specific Gravity: 2.2

Bulk Density: 56 ln/ft3 (900kg/m3)

Product Code : Product Description

PRS-A0620 : Micro-Deval Apparatus, 220-240 V 50 Hz (60 Hz version is available upon request)

PRS-A0620/110 : Micro-Deval Apparatus, 110 V 60 Hz

PRS-A0621 : Stainless Steel Drum Ã? 200x154 mm EN 1097-1

PRS-A0622 : Stainless Steel Drum Ã? 200x400 mm EN 13450

PRS-A0623 : Micro-Deval Abrasion Charges Ã?10 mm 25 kg Pack, EN 1097-1

The Micro Deval Testing Machine is used to determine the resistance to wear of aggregates. The machine consists of a steel frame, two stainless steel cylinders, and 25 kg of 10 mm diameter stainless steel spheres and an automatic digital counter which allows machine to stop automatically at the preset number of revolutions.
Stainless steel drums are rotating at a speed of 100 ± 5 r.p.m.

The machine can accept up to 4 pcs. Ã? 200x154 mm drums or 2 pcs. Ã? 200x400 mm drums.

Ã? 200x400 mm steel drums and 1,6 mm sieve should be ordered separately.

The Micro-Deval Apparatus is supplied complete with;

â?¢Stainless Steel Drum, Ã? 200x154 mm, 2 pcs.

â?¢Abrasion Charges, 25 kg, Ã? 10mm

Dimensions1100x400x1000 mm

Weight (approx.)140 kg

Power750 W

PRS-EU8050 " Electromechanical Universal Test Machine, 50 kN, 220-240V, 50-60Hz, 1 ph.

PRS-EU8300 " Electromechanical Universal Test Machine, 300 kN, 220-240V, 50-60Hz, 1 ph.

PRS-EU8050, 50 kN and PRS-EU8300, 300 kN capacity fully automatic Electromechanical ParsRos Universal Testing Machines are multi purpose versatile machines which satisfy the requirement of R&D laboratories, university laboratories, institute laboratories and quality control laboratories for tensile, compression flexural tests under load or displacement control for a wide range of materials. PRS-EU8050 and PRS-EU8300 model Electromechanical Universal Testing Machines can be used for tensile test on any material i.e (metal, plastic, textile, wood) by using suitable accessories.

Those machines can also be used for general compression, flexural, test on steel, soil, concrete, cement, asphalt and similar materials, by using suitable accessories.
These Testing Machines consist of base containing the transmission components and holds two robust columns connected by upper cross head and digital graphics data acquisition and control system.

The upper cross head can be adjusted to set the vertical test space for different tests. User can adjust the vertical test space by also lower crosshead moved by an electromechanical system with a single recirculating ball screw, powered by an servomotor.

Advanced closed loop control system assures accurate load or displacement pace rate on sample.

The load is measured by a load cell that located on upper crosshead and displacement is measured by an encoder fit to the servo motor on both models.

The operator will have large flexibility during the test with advanced microprocessor control and material testing software installed on PC.

The machine is supplied complete with high precision load cell. Gripping systems, extensometers and accessories are not included and have to be ordered separately.

ParsRos Automatic Compression Testing Machines

Product code

PRS-B423 2000 kN Automatic Compression Testing Machine EN, 220-240 V 50-60 Hz

PRS-B6321 2000 kN Automatic Compression Testing Machine ASTM, 220-240 V 50-60 Hz

PRS-B6321/11 2000 kN Automatic Compression Testing Machine ASTM, 110 V 60 Hz

PRS-B433 3000 kN Automatic Compression Testing Machine EN, 220-240 V 50-60 Hz

PRS-B63000 kN Automatic Compression Testing Machine ASTM, 220-240 V 50-60 Hz

PRS-B6331/110 3000 kN Automatic Compression Testing Machine ASTM, 110 V 60 Hz
PRS-B0210 High Precision Pressure Transducer and Electronic


PARSROS Automatic range of 2000 kN and 3000 kN capacity compression testing machines have been designed for reliable and consistent testing of a wide range of specimens.

These compression testers are the results of continu¨ous research to upgrade the testing machines with the latest technologies to conform to the latest standards EN 12390-3, 12390- 4, BS 1881 and ASTM C39 in terms of its technical properties taking into account client requirements. These also meet the requirements of CE norms for the safety and health of the operator.

The advantages of performing tests on computer with using PARSROS Software, such as reporting, graphical output, etc.,


PRS-B4321and PRS-B4331Testing Machine is supplied complete with;
205x90 mm, �? 205x50 mm and �? 205x30 mm distance pieces

PRS-B4513 Upper Platen (with ball seating assembly) 300 mm, Lower Platen 300
mm.

PRS-B4510, PRS-B4511, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B4321 and PRS-B4331 testing machines.

PRS-B6321 and PRS-B6331 Compression Testing Machines are supplied complete with;
165x90 mm, 165x50 mm and 2 pcs. 165x30 mm distance pieces

PRS-B4511 Upper Platen (with ball seating assembly) 165 mm, Lower Platen 165 mm.
PRS-B4510, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B6321 and PRS-B6331 Compression Testing Machines.
Safety Features
Maximum pressure valves to avoid machine overloading
Piston travel limit switch
Emergency stop button
Front and rear transparent durable plexiglas guards
Software controlled maximum load value

Product Code Product Description

PRS-B42212000 kN Semi-Automatic Compression Testing Machine EN, 220-240 V 50-60 Hz

PRS-B62212000 kN Semi-Automatic Compression Testing Machine ASTM, 220-240 V 50-60 Hz

PRS-B6221/1102000 kN Semi-Automatic Compression Testing Machine ASTM, 110 V 60 Hz

PRS-B43213000 kN Semi-Automatic Compression Testing Machine EN, 220-240 V 50-60 Hz

PRS-B63213000 kN Semi-Automatic Compression Testing Machine ASTM, 220-240 V 50-60 Hz

PRS-B6321/1103000 kN Semi-Automatic Compression Testing Machine ASTM, 110 V 60 Hz

PRS-B0210High Precision Pressure Transducer and Electronic


PARSROS Semi-Automatic (Motorized) range of 2000 kN and 3000 kN capacity compression testing machines have been designed for re¬liable and consistent testing of a wide range of specimens.

These compression testers are manufactured as a result of continuous research studies to upgrade the machines with the latest technologies to conform with the latest standards EN 12390-3, 12390-4, BS 1881 and ASTM C39 in terms of its tech¬nical properties taking into account the cli-ent requirements.

PRS-B4221 and PRS-B4321Testing Machine is supplied complete with;

â?¢dia. 205x90 mm, dia 205x50 mm and dia 205x30 mm distance pieces

â?¢PRS-B4513 Upper Platen (with ball seating assembly) Ã?300 mm, Lower Platen Ã?300 mm.

PRS-B4510, PRS-B4511, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B4221 and PRS-B4321 testing machines.

PRS-B6221 and PRS-B6321 Compression Testing Machines are supplied complete with;

â?¢dia165x90 mm, dia 165x50 mm and 2 pcs Ã? 165x30 mm distance pieces

â?¢PRS-B4511 Upper Platen (with ball seating assembly) Ã?165 mm, Lower Platen Ã?165 mm.

PRS-B4510, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B6221 and PRS-B6321 Compression Testing Machines.

Product Code Product Description

PRS-AS0120 Semi-Automatic Digital Bitumen Penetrometer 220-240 V 50-60 Hz

PRS-AS0120/110 Semi-Automatic Digital Bitumen Penetrometer 110 V 60 Hz

PRS-AS0121 Transfer Dish for PRS-AS0120

PRS-AS0122 Sample Cup, Ã? 55x35 mm, stainless steel

PRS-AS0123 Sample Cup, Ã? 70x45 mm, stainless steel

PRS-AS0124 Penetration Needle, 2,5 g

PRS-AS0160 One-Quarter Scale Cone and Shaft, ASTM D 1403 and D 1831, for PRS-AS0120 and PRS-AS0126

PRS-AS0161 One-Half Scale Cone and Shaft, ASTM D 1403 and D 1831, for PRS-AS0120 and PRS-AS0126

PRS-AS0162 Penetrometer Cone ASTM D 217 (Optional Type) and ASTM D 937, for PRS-AS0120 and PRS-AS0126, Brass

PRS-AS0165 Resilience Ball Penetration Tool. ASTM D5329, for PRS-AS0120 and PRS-AS0126

STANDARDS : EN 1426; ASTM D5; AASHTO T49
The PRS-AS0120 Semi-Automatic Digital Bitumen Penetrometer is used to determine the penetration of bituminous samples under constant load, time and temperature. The Penetrometer consists of a cast iron base with coarse and fine levelling screws, a digital penetration measurement gauge 0.01 mm readability and a penetration timer unit.
Start button of the penetration timer unit is used to release the plunger fitted with the needle to start the 5 seconds test.
A water bath (PRSGE-AS4000 or PRSGE-AS4050, 25±0,1 C) and a thermometer ( IP38, ASTM 17C or 63C ) required for the test should be ordered separately.


The Semi-Automatic Digital Bitumen Penetrometer is supplied complete with;
â?¢ Penetration Needle, 2,5g, 1 pieces
â?¢ Transfer Dish
â?¢ Sample Cup Ã? 55x35 mm, 3 pieces, stainless steel
Dimensions 200x300x500 mm
Weight (approx.) 16 kg

Laminar Flows

Product Code Product Description

PRS-KU1480 Laminar Flow (Fume Hood) Over the Counter Type

PRS-KU1482 Laminar Flow (Fume Hood) - Cabinet Type

STANDARDS

Some tests, especially extraction methods, require the use of volatile toxic chemicals which are hazardous to health, and these gases are subject to occupational exposure limits as described in relevant legislation and regulations

The PRS-KU1480 and PRS-KU1482 , Over The Counter and Cabinet Type Fume Hoods are especially designed to remove toxic gases from the test area. Bespoke Fume Hoods with specific dimensions and properties can be supplied to meet specific requirements, pleasecontact PARSROS for more information.

Standard Features

Stoneware Bench

Water and gas fittings

2 x double Electric Socket, 220 V

Galvanized frame

Legs that made from hard PVC to be protected against corrosion,

Second air drained part for draining heavy gases,

Standard flammable gas tap for LPG, Acetylene, Propane, Butaneâ?¦etc,

Pressure Reducing Regulator,

Laminated or Tampered glass

Optional Features

Digital Indicator and control panel ,

Fan min. 1200 m3/h capacity

Trespa Top Lab Plus or Epoxy Resin type bench surface,

Demineralized water fitting

Product Code Dimensions Weigth(approx.)

PRS-KU1480 1500x900x1620 mm 250 kg

PRS-KU1482 1500x900x2350 mm 300 kg

Product Code : Product Description

PRS-ZE0095 : Dynamic Cone Penetrometer (DCP)

STANDARDS :

The PRS-ZE0095 Dynamic Cone Penetrometer is used for the rapid, in situ measurement of structural properties of existing road pavement constructed with unbound materials.

it incorporates an 8 kg weight dropping through a height of 575 mm and 60° cone having a diameter of 20 mm. with the standard DCP measurements can be made down to a depth of approximately 850 mm or when extension shafts are used to a recommended maximum depth of 2 m.

Readings are usually taken after a set number of blows, changing the number according to the strength of the layer being penetrated. A typical test takes only a few minutes, therefore the instrument provides a very efficient method of obtaining information that would normally require the digging of test pits.

The penetration hammer assembly consists of 8 kg hammer, hammer shaft, anvil with plastic plate coupling for ruler and handle.

The Dynamic Cone Penetrometer is supplied complete with;
A hammer assembly,
Penetration rod,
2 piece 60° cone,
Metal plate coupling for ruler,
Segmented adaptor for extension rods,
Segmented upper extension rod,
Segmented lower extension rod,
2 piece 13-17mm AF spanners,
3mm AF hex wrench,
Tommy bar,
A bottle of adhesive,10cc,
Users Manual
Steel ruler,
Carrying Case, heavy-duty wooden