Find Verified Sweet Lime Suppliers, Manufacturers and Wholesalers

Product Code Product Description

PRS-CETLS025 Lever Support

STANDARDS : EN 13294,TS EN 1015-9
Lever supported(Drill-Holder Type)
It is complete with washer and penetration rod brass made, clamp and locking support.
The machine is used for the determination of processing and rectifying of fresh mortarâ??s duration.
Dimensions 380 x 300 x (h)500 mm
Weight (approx.) 12 kg

Product Code Product Description

PRS-CM0073 Mud Balance

The PRS-CM0073 Mud Balance, an ideal equipment for site applications, provides an accurate and easy method for determining the mud density. The accuracy of the readings is not affected by the temperature of the drilling mud.

The equipment consists of a base and a graduated arm with an integral spirit level, counter weight, cup, lid, rider, knife-edge. Supplied with a special plastic carrying case which can be used to stabilize the equipment at the working position.

Dimensions 550x110x100 mm

Weight (approx.) 1 kg

Product Code Product Description

PRS-CM0070 Slaking Vessel

STANDARDS : EN 459-2

PRS-CM0070 Slaking Vessel is used to determine the yield of lime by leaving the lime sample to slake into. Stainless steel made and double walled insulated. The cylinder has inside dimensions dia. 113 mm by 140 mm deep. Supplied complete with cover.

Dimensions 120x120x160 mm
Weight (approx.) 4 kg

Product Code Product Description

PRS-CM0069 Bulk Density Apparatus

STANDARDS : EN 459-2

The bulk density of lime is of interest for storage and packaging and for determining volume and capacity of mixing equipment necessary for processing the material.

The PRS-CM0069 Bulk Density Apparatus is designed to determine bulk density by allowing a sample to fall from a known height into a volumetric container.

The apparatus consists of a hopper, 1 liter capacity cylindrical container and a spring-loaded trap.

Dimensions 250x250x750 mm

Weight (approx.) 2 kg

Product Code Product Description

PRS-CM0058 Gillimore Apparatus

STANDARDS : ASTM C91, C141, C150, C266; AASHTO T154

The PRS-CM0058 Gillmore Apparatus is used to determine the setting time of cement hydraulic hydrometer lime and mortar. Apparatus consists of two horizontally positioned arms, carrying weighted needles, initial needle has a 2.12 mm diameter and 113.4 g in weight and the final needle has a 1.06 mm diameter and 453.6 g in weight.

Dimensions 300x100x300 mm
Weight (approx.) 2,5 kg

Product Code Product Description

PRS- CM0065 Plunger Penetration Apparatus

STANDARDS : EN 413-2, 459-2, 1015-4

Plunger Penetration Apparatus is used to determine the consistency of fresh mortar, building lime and masonry cement. The test apparatus consists of a base to place the test cup and a vertical column holding the penetration plunger assembly.

The drop default height is adjusted to 100 mm. The plunger assembly weight is 90 g.

The Plunger Penetration Apparatus is supplied complete with;

Test cup, Ã? 80 mm x 70 mm

Tamper

Dimensions 200x200x600 mm

Weight (approx.) 6 kg

Product Code Product Description

PRS-CM0010 Le Chatelier Mould

PRS-CM0014 Le Chatelier Soundness Kit

STANDARDS : EN 196-3, 450-1, 459-2; EN ISO 9597

The soundness of cement, fly ash for concrete and lime is determined by using the Le Chatelier moulds and Le Chatelier Water Bath (PRS-CM0016) according to the relevant standard.

The Le Chatelier Soundness Kit is supplied complete with;
Le Chatelier moulds 3 pcs.
50x50 mm glass plates 6 pcs.
300 gr Weights 1 pcs.
100 gr Weight, 3 pcs.
Tamping Rod 17 mm dia. x 70 gr
Steel Ruler
Plastic Carrying Case

Dimensions 340x290x80 mm

Weight (approx.) 2 kg

Air Entrainment Meter for Mortar

Product Code Product Description

PRS-CM0066 Air Entrainment Meter for Mortar 1 lt.

STANDARDS : EN 413-2, 459-2, 1015-7

The PRS-CM0066 Air Entrainment Meter for Mortar is used for determining the air content of cement paste, cement mortar and lime mortar. The air entrainment meter is manufactured from cast aluminum, the upper part and the lower test pot are held together with an air-tight seal which are easily adjusted by using the two spring clamps.

The pressure gauge is installed in the head of the meter and the scale works in the 0-20 volumetric % range. The air is compressed with a hand pump installed in the system and the smart configuration of the test and correction buttons enables fast and simple testing.

Dimensions 200x200x320 mm
Weight (approx.) 3,5 kg

Product Code Product Description

PRS-CM1462 Muffle Furnace 5 lt. 1200°C Max. Temperature with Programmable Timer, 20-240 V 50-60 Hz

STANDARDS : EN 196-2; ASTM C25, C115

PRS-CM1462 Muffle Furnace is used for determining the loss on ignition and insoluble residue of cement and building lime.

Working temprature and time can be programmed with PID digital control system.

Digital Thermometer Features

Temperature Controller PC 442/2

Max. Temperature 1200 °C

Max. Continuous Temperature 1150 °C

Temperature Deviation at Set Point ± 2°C

Heat Up Time to Max. Temperature 50. min

Internal Volume 5 L

Phase 1

Internal Dimension 140x180x200 mm

External Dimension 650x550x580 mm

Weight (approx.) 56 kg

Power 2000 W

Product Code Product Description

PRS-CM0016 Le Chatelier Water Bath, 220-240 V 50-60 Hz

STANDARDS : EN 196-3, 450-1, 459-2; EN ISO 9597

The PRS-CM0016 Le Chatelier Water Bath is used with Le Chatelier moulds for the determination of the soundness of cement paste fly ash for concrete and lime. The internal chamber and the insulated exterior case of the bath are manufactured from stainless steel. The Bath is capable of reaching boiling point in 30 minutes by using two heater units.

There is a timer on the PRS-CM0016 Le Chatelier Water Bath which is used to set the time for reaching the boiling point. After that time the temperature of water is regulated by using one heater unit to conserve energy. Supplied complete with a removable rack to hold up to 10 moulds. A cover is also supplied as standard.
Dimensions 210x470x290 mm
Weight (approx.) 8 kg
Power 1250 W

Product Code : Product Description

PRS-A0620 : Micro-Deval Apparatus, 220-240 V 50 Hz (60 Hz version is available upon request)

PRS-A0620/110 : Micro-Deval Apparatus, 110 V 60 Hz

PRS-A0621 : Stainless Steel Drum Ã? 200x154 mm EN 1097-1

PRS-A0622 : Stainless Steel Drum Ã? 200x400 mm EN 13450

PRS-A0623 : Micro-Deval Abrasion Charges Ã?10 mm 25 kg Pack, EN 1097-1

The Micro Deval Testing Machine is used to determine the resistance to wear of aggregates. The machine consists of a steel frame, two stainless steel cylinders, and 25 kg of 10 mm diameter stainless steel spheres and an automatic digital counter which allows machine to stop automatically at the preset number of revolutions.
Stainless steel drums are rotating at a speed of 100 ± 5 r.p.m.

The machine can accept up to 4 pcs. Ã? 200x154 mm drums or 2 pcs. Ã? 200x400 mm drums.

Ã? 200x400 mm steel drums and 1,6 mm sieve should be ordered separately.

The Micro-Deval Apparatus is supplied complete with;

â?¢Stainless Steel Drum, Ã? 200x154 mm, 2 pcs.

â?¢Abrasion Charges, 25 kg, Ã? 10mm

Dimensions1100x400x1000 mm

Weight (approx.)140 kg

Power750 W

PRS-EU8050 " Electromechanical Universal Test Machine, 50 kN, 220-240V, 50-60Hz, 1 ph.

PRS-EU8300 " Electromechanical Universal Test Machine, 300 kN, 220-240V, 50-60Hz, 1 ph.

PRS-EU8050, 50 kN and PRS-EU8300, 300 kN capacity fully automatic Electromechanical ParsRos Universal Testing Machines are multi purpose versatile machines which satisfy the requirement of R&D laboratories, university laboratories, institute laboratories and quality control laboratories for tensile, compression flexural tests under load or displacement control for a wide range of materials. PRS-EU8050 and PRS-EU8300 model Electromechanical Universal Testing Machines can be used for tensile test on any material i.e (metal, plastic, textile, wood) by using suitable accessories.

Those machines can also be used for general compression, flexural, test on steel, soil, concrete, cement, asphalt and similar materials, by using suitable accessories.
These Testing Machines consist of base containing the transmission components and holds two robust columns connected by upper cross head and digital graphics data acquisition and control system.

The upper cross head can be adjusted to set the vertical test space for different tests. User can adjust the vertical test space by also lower crosshead moved by an electromechanical system with a single recirculating ball screw, powered by an servomotor.

Advanced closed loop control system assures accurate load or displacement pace rate on sample.

The load is measured by a load cell that located on upper crosshead and displacement is measured by an encoder fit to the servo motor on both models.

The operator will have large flexibility during the test with advanced microprocessor control and material testing software installed on PC.

The machine is supplied complete with high precision load cell. Gripping systems, extensometers and accessories are not included and have to be ordered separately.

ParsRos Automatic Compression Testing Machines

Product code

PRS-B423 2000 kN Automatic Compression Testing Machine EN, 220-240 V 50-60 Hz

PRS-B6321 2000 kN Automatic Compression Testing Machine ASTM, 220-240 V 50-60 Hz

PRS-B6321/11 2000 kN Automatic Compression Testing Machine ASTM, 110 V 60 Hz

PRS-B433 3000 kN Automatic Compression Testing Machine EN, 220-240 V 50-60 Hz

PRS-B63000 kN Automatic Compression Testing Machine ASTM, 220-240 V 50-60 Hz

PRS-B6331/110 3000 kN Automatic Compression Testing Machine ASTM, 110 V 60 Hz
PRS-B0210 High Precision Pressure Transducer and Electronic


PARSROS Automatic range of 2000 kN and 3000 kN capacity compression testing machines have been designed for reliable and consistent testing of a wide range of specimens.

These compression testers are the results of continu¨ous research to upgrade the testing machines with the latest technologies to conform to the latest standards EN 12390-3, 12390- 4, BS 1881 and ASTM C39 in terms of its technical properties taking into account client requirements. These also meet the requirements of CE norms for the safety and health of the operator.

The advantages of performing tests on computer with using PARSROS Software, such as reporting, graphical output, etc.,


PRS-B4321and PRS-B4331Testing Machine is supplied complete with;
205x90 mm, �? 205x50 mm and �? 205x30 mm distance pieces

PRS-B4513 Upper Platen (with ball seating assembly) 300 mm, Lower Platen 300
mm.

PRS-B4510, PRS-B4511, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B4321 and PRS-B4331 testing machines.

PRS-B6321 and PRS-B6331 Compression Testing Machines are supplied complete with;
165x90 mm, 165x50 mm and 2 pcs. 165x30 mm distance pieces

PRS-B4511 Upper Platen (with ball seating assembly) 165 mm, Lower Platen 165 mm.
PRS-B4510, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B6321 and PRS-B6331 Compression Testing Machines.
Safety Features
Maximum pressure valves to avoid machine overloading
Piston travel limit switch
Emergency stop button
Front and rear transparent durable plexiglas guards
Software controlled maximum load value

Product Code Product Description

PRS-B42212000 kN Semi-Automatic Compression Testing Machine EN, 220-240 V 50-60 Hz

PRS-B62212000 kN Semi-Automatic Compression Testing Machine ASTM, 220-240 V 50-60 Hz

PRS-B6221/1102000 kN Semi-Automatic Compression Testing Machine ASTM, 110 V 60 Hz

PRS-B43213000 kN Semi-Automatic Compression Testing Machine EN, 220-240 V 50-60 Hz

PRS-B63213000 kN Semi-Automatic Compression Testing Machine ASTM, 220-240 V 50-60 Hz

PRS-B6321/1103000 kN Semi-Automatic Compression Testing Machine ASTM, 110 V 60 Hz

PRS-B0210High Precision Pressure Transducer and Electronic


PARSROS Semi-Automatic (Motorized) range of 2000 kN and 3000 kN capacity compression testing machines have been designed for re¬liable and consistent testing of a wide range of specimens.

These compression testers are manufactured as a result of continuous research studies to upgrade the machines with the latest technologies to conform with the latest standards EN 12390-3, 12390-4, BS 1881 and ASTM C39 in terms of its tech¬nical properties taking into account the cli-ent requirements.

PRS-B4221 and PRS-B4321Testing Machine is supplied complete with;

â?¢dia. 205x90 mm, dia 205x50 mm and dia 205x30 mm distance pieces

â?¢PRS-B4513 Upper Platen (with ball seating assembly) Ã?300 mm, Lower Platen Ã?300 mm.

PRS-B4510, PRS-B4511, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B4221 and PRS-B4321 testing machines.

PRS-B6221 and PRS-B6321 Compression Testing Machines are supplied complete with;

â?¢dia165x90 mm, dia 165x50 mm and 2 pcs Ã? 165x30 mm distance pieces

â?¢PRS-B4511 Upper Platen (with ball seating assembly) Ã?165 mm, Lower Platen Ã?165 mm.

PRS-B4510, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B6221 and PRS-B6321 Compression Testing Machines.

Product Code Product Description

PRS-AS0120 Semi-Automatic Digital Bitumen Penetrometer 220-240 V 50-60 Hz

PRS-AS0120/110 Semi-Automatic Digital Bitumen Penetrometer 110 V 60 Hz

PRS-AS0121 Transfer Dish for PRS-AS0120

PRS-AS0122 Sample Cup, Ã? 55x35 mm, stainless steel

PRS-AS0123 Sample Cup, Ã? 70x45 mm, stainless steel

PRS-AS0124 Penetration Needle, 2,5 g

PRS-AS0160 One-Quarter Scale Cone and Shaft, ASTM D 1403 and D 1831, for PRS-AS0120 and PRS-AS0126

PRS-AS0161 One-Half Scale Cone and Shaft, ASTM D 1403 and D 1831, for PRS-AS0120 and PRS-AS0126

PRS-AS0162 Penetrometer Cone ASTM D 217 (Optional Type) and ASTM D 937, for PRS-AS0120 and PRS-AS0126, Brass

PRS-AS0165 Resilience Ball Penetration Tool. ASTM D5329, for PRS-AS0120 and PRS-AS0126

STANDARDS : EN 1426; ASTM D5; AASHTO T49
The PRS-AS0120 Semi-Automatic Digital Bitumen Penetrometer is used to determine the penetration of bituminous samples under constant load, time and temperature. The Penetrometer consists of a cast iron base with coarse and fine levelling screws, a digital penetration measurement gauge 0.01 mm readability and a penetration timer unit.
Start button of the penetration timer unit is used to release the plunger fitted with the needle to start the 5 seconds test.
A water bath (PRSGE-AS4000 or PRSGE-AS4050, 25±0,1 C) and a thermometer ( IP38, ASTM 17C or 63C ) required for the test should be ordered separately.


The Semi-Automatic Digital Bitumen Penetrometer is supplied complete with;
â?¢ Penetration Needle, 2,5g, 1 pieces
â?¢ Transfer Dish
â?¢ Sample Cup Ã? 55x35 mm, 3 pieces, stainless steel
Dimensions 200x300x500 mm
Weight (approx.) 16 kg

Laminar Flows

Product Code Product Description

PRS-KU1480 Laminar Flow (Fume Hood) Over the Counter Type

PRS-KU1482 Laminar Flow (Fume Hood) - Cabinet Type

STANDARDS

Some tests, especially extraction methods, require the use of volatile toxic chemicals which are hazardous to health, and these gases are subject to occupational exposure limits as described in relevant legislation and regulations

The PRS-KU1480 and PRS-KU1482 , Over The Counter and Cabinet Type Fume Hoods are especially designed to remove toxic gases from the test area. Bespoke Fume Hoods with specific dimensions and properties can be supplied to meet specific requirements, pleasecontact PARSROS for more information.

Standard Features

Stoneware Bench

Water and gas fittings

2 x double Electric Socket, 220 V

Galvanized frame

Legs that made from hard PVC to be protected against corrosion,

Second air drained part for draining heavy gases,

Standard flammable gas tap for LPG, Acetylene, Propane, Butaneâ?¦etc,

Pressure Reducing Regulator,

Laminated or Tampered glass

Optional Features

Digital Indicator and control panel ,

Fan min. 1200 m3/h capacity

Trespa Top Lab Plus or Epoxy Resin type bench surface,

Demineralized water fitting

Product Code Dimensions Weigth(approx.)

PRS-KU1480 1500x900x1620 mm 250 kg

PRS-KU1482 1500x900x2350 mm 300 kg

Product Code : Product Description

PRS-ZE0095 : Dynamic Cone Penetrometer (DCP)

STANDARDS :

The PRS-ZE0095 Dynamic Cone Penetrometer is used for the rapid, in situ measurement of structural properties of existing road pavement constructed with unbound materials.

it incorporates an 8 kg weight dropping through a height of 575 mm and 60° cone having a diameter of 20 mm. with the standard DCP measurements can be made down to a depth of approximately 850 mm or when extension shafts are used to a recommended maximum depth of 2 m.

Readings are usually taken after a set number of blows, changing the number according to the strength of the layer being penetrated. A typical test takes only a few minutes, therefore the instrument provides a very efficient method of obtaining information that would normally require the digging of test pits.

The penetration hammer assembly consists of 8 kg hammer, hammer shaft, anvil with plastic plate coupling for ruler and handle.

The Dynamic Cone Penetrometer is supplied complete with;
A hammer assembly,
Penetration rod,
2 piece 60° cone,
Metal plate coupling for ruler,
Segmented adaptor for extension rods,
Segmented upper extension rod,
Segmented lower extension rod,
2 piece 13-17mm AF spanners,
3mm AF hex wrench,
Tommy bar,
A bottle of adhesive,10cc,
Users Manual
Steel ruler,
Carrying Case, heavy-duty wooden

Product Code : Product Description

PRS-ZE0865 : In-situ CBR Test Apparatus

PRS-ZE0866 : Cutting Collar (edge) for PRS-ZE0865

PRS-ZE0867 : Conversion Frame

STANDARDS :

The PRS-ZE0865 -situ CBR Test Apparatus, 50 kN capacity,is used for the on-site determination of the bearing capacity of soils used in road construction.

The set consists of:
50 kN capacity mechanical jack with ball seating
50 kN capacity load ring
Analog penetration dial gauge (30 mm travel x 0.01 mm)
Adjustable dial gauge holder
CBR Penetration piston
Set of extension rods (2 pcs. 102 mm, 1 pcs. 305 mm and 1 pcs. 610 mm length)
Datum bar assembly with two stands
4.5 kg annular surcharge weight
4.5 Kg slotted surcharge weight
9 kg slotted surcharge weight
Vehicle bracket and wooden carrying case

The PRS-ZE0867 Conversion Frame is used to convert the IN-situ CBR test to a mechanical laboratory CBR test machine.

The system is easily assembled onto the conversion frame with the addition of some of the accessories included in PRS-ZE0865. The frame is used with the jack, load ring, CBR mould and penetration piston.

Product Code : Product Description

PRSâ??A0600 : Los Angeles Abrasion Machine (60 Hz version is available upon request)

PRSâ??A0600/110 : Los Angeles Abrasion Machine 110 V 60 Hz

PRSâ??A0601 : Los Angeles Abrasion Machine with Soundproof Safety Cabinet 220-240 V 50Hz

PRSâ??A0601/110 : Los Angeles Abrasion Machine with Soundproof Safety Cabinet, 110 V 60 Hz

PRSâ??A0602/E : Los Angeles Abrasion Charges EN,12 pcs.

PRSâ??A0602/A : Los Angeles Abrasion Charges ASTM/AASHTO, 12 pcs.

PRSâ??A0605 : Soundproof Safety Cabinet for Los Angeles Abrasion Machine

The Los Angeles Abrasion Machine is used for determination of the aggregates resistance to fragmentation. The machine consists of an electronic control unit and a rolled steel drum having an inside diameter of 711 mm and internal length of 508 mm. The drum is rotated at a speed of 31-33 r.p.m. The internal shelf provided with the machine confirms to ASTM, AASHTO and EN standards.

The machine is equipped with an automatic counter, when the preset revolution count is reached, the machine will stop automatically. The drum is equipped with an interlock device which allows the operator to lock the drum into position for easy loading/unloading of the sample.

A steel tray is supplied with the machine for easy discharge of specimen and abrasive charges.

The standard model can be supplied with a safety/noise reduction cabinet. The cabinet is lined internally with soundproofing material to reduce sound level conforming to CE directives.

Electronic Analytical Balances

Product Code Product Description

PRSW-0620Electronic Analytical Balance, LCD Screen 60-220 g x 0.00001-0.0001 g

PRSW -0622Electronic Analytical Balance LCD Screen 220 g x 0.0001 g

PRSW -0625Electronic Analytical Balance 200 g x 0.001 g

PRSW -0628Electronic Analytical Balance 360 g x 0.001 g

PRSW -0630Electronic Analytical Balance 510 g x 0.001 g

PRSW -0631Electronic Analytical Balance 750 g x 0.001 g

PRSW -0632Electronic Analytical Balance 1000 g x 0.001 g

Features

The PRSW Series Electronic Analytical Balances set the standard in terms of reliable measurements, user-friendly and long service life. Offering capacities from 200 g to 510 g with high sensitivities up to 0.01 mg readability makes these balances ideal for weighing small sample amounts. The balances can be used for routine tasks and/or complicated weighing procedures.

The PRSW-0620 and PRSW-0622 models have an automatic internal calibration feature, the other models in the range require external calibration.

The PRSW Series Analytical Balances provide fast and easy installation and cleaning with their ergonomic designs and brilliant displays. They can also be connected to printers or PC's through RS 232 outputs to give excellent monitoring and reporting performance.

Product CodeCapacityReadability Pan Size Additional Power Supply

PRSW-0620 60-220 g0.01-0.1 mg Ã? 70 AC Adapter

PRSW -0622220 g0.1 mgÃ? 85 Adapter

PRSW -0625200 g1 mgÃ? 115 Rechargable Battery

PRSW -0628360 g1 mg128x128 mm AC Adapter

PRSW -0630510 g1 mg128x128 mm AC Adapter

PRSW -0631750 g1 mg128x128 mm AC Adapter

PRSW -06321000 g1 mg128x128 mm AC Adapter

Product Code Product Description

PRSD-1450 Muffle Furnace 3 lt. 1000°C, 220-240 V 50-60 Hz

PRSD-1455 Muffle Furnace 6 lt. 1100°C, 220-240 V 50-60 Hz

PRSD-1460 Muffle Furnace 5 lt. 1200°C, 220-240 V 50-60 Hz

PRSD-1462 Muffle Furnace 5 lt. 1200°C Programmable Timer, 220-240 V 50-60 Hz

PRSD-1465 Muffle Furnace 5 lt. 1600°C, 380 V 50 Hz

The PRSD Series Muffle Furnaces are widely used for determining various properties of construction materials, and they cover a temperature range from 1100°C to 1600°C, they are all front loading for easy operation and are of a double skin construction to maintain a cool outer case. Up to 1300°C, open wire based models are also produced.

Excellent temperature control is provided by a PID digital control system. A vertical counter balanced door keeps the hot insulation away from the operator which opens in an upward movement. The Furnace has a safety switch which isolates the power when the door is opened.

Testing Sieves

STANDARDS : EN 933-2; ISO 565, 3310-1, 3310-2; ASTM E11, 323

PARSROS offers a wide range of High Quality Testing Sieves which are used in all types of sieve testing applications, from sampling and classification of soils, aggregates and other powdered and granular materials. PARSROS testing sieves are of the highest quality to ensure consistent fit, accurate specifications and durable construction.

Woven Wire Cloth and Perforated Plate Sieves are supplied in 200 mm and 300 mm frame diameters in various nominal aperture sizes suitable for several applications and standards. Wet Washing Sieves are used for wet testing of various materials enabling to wash the fines through the sieve without losing any of the sample. Available in 200 mm diameter with 100 mm and 200 mm deep models.

All parts of testing sieves are manufactured from stainless steel. Receiving Pans and Lids are available in stainless steel with 200 mm and 300 mm diameters.

Product Code : Product Description

PRSG-0420 High Capacity Screen Shaker Time-Controlled, 220-240 V 50-60 Hz

PRSG-0420/110 High Capacity Screen Shaker Time-Controlled, 110 V 60 Hz

PRSG-0422 High Capacity Screen Shaker Frequency & Time-Controlled, 220-240 V 50-60 Hz
PRSG-0422/110 High Capacity Screen Shaker, Frequency and Time-Controlled, 110 V 60 Hz

PRSG-0425 Pan

PRSG-0426 Soundproof Safety Cabinet

STANDARDS : EN 1339, 1367-1; TS 2824
The PRSG-0420 and PRSG-0422 are ideal for sizing large quantities of crushed stones, sand, gravel, slag, coal, coke, ores, pellets and similar materials. The screen shaker has a capacity of approx. 30 kg of sample. To be use with 667x452x67 mm dimension screens. The shaker has 6 screens and 1 pan capacity.
PRSG-0420 model is time-controlled, PRSG-0422 model is frequency and time-controlled.
Various sized wowen wired from 100 mm (4â?�) to 4 mm (no.5) or perforated plate from125mm to 5.6mm screen trays are available on request.
PRSG-0426 Soundproof Safety Cabinet is manufactured from sheet steel lined internally with soundproofing material to reduce noise and for protection from dust.
Screen trays and Soundproof Safety Cabinet (PRSG-0426) should be ordered separately.
The PRSG-0420 or PRSG-0422 is supplied complete with;
â?¢ Pan (PRSG-0425)

Woven Wire Cloth Screen Trays ASTM E11 Perforated Plate Screen Trays
Product Code Aperture mm (in) Product Code Aperture mm (in)
PRSG-8WC1000 100 mm (4 in) PRSG -8PC0056 5.6
PRSG-8WC0900 90 mm (3 ½ in) PRSG -8PC0080 8
PRSG-8WC0750 75 mm (3 in) PRSG -8PC0112 11.2
PRSG-8WC0630 50 mm (2 in) PRSG -8PC0160 16
PRSG-8WC0500 45 mm (1 ¾ in) PRSG -8PC0224 22.4
PRSG-8WC0450 37.5 mm (1 ½ in) PRSG -8PC0315 31.5
PRSG-8WC0375 31.5 mm (1 ¼ in) PRSG -8PC0450 45
PRSG -8WC0315 25 mm (1 in) PRSG -8PC0630 63
PRSG -8WC0250 22.4 mm (7/8 in) PRSG -8PC1250 90
PRSG -8WC0190 19 mm (¾ in) 125
PRSG -8WC0160 16 mm (5/8 in)
PRSG -8WC0125 12.5 mm (½ in)
PRSG -8WC0112 11.2 mm (7/16 in)
PRSG -8WC0095 9.5 mm (3/8 in)
PRSG -8WC0080 8 mm (5/16 in)
PRSG -8WC0063 6.3 mm (¼ in)
PRSG -8WC0056 5.6 mm (No. 3 ½ in)
PRSG -8WC0047 4.75 mm (No. 4 in)
PRSG -8WC0040 4 mm (No. 5 in)

SCREEN SHAKER
Dimension 587x787x850 mm
Weight (approx.) 170 kg
Power 550 W

SCREEN TRAYS
Dimensions 667x452x67 mm
Weight (approx.) 7 kg

Product Code Product Description

PRS-CM0075 Manuel Mortar Mixer, 220-240 V 50-60 Hz

PRS-CM0075/110 Manuel Mortar Mixer, 110 V 60 Hz

PRS-CM0076 Spare Bowl for PRS-CM0075 and PRS-CM0085, 5 L

PRS-CM0078 Spare Beater for PRS-CM0075 and PRS-CM0085

STANDARDS : EN 196-1, 196-3, 413-2, 459-2, 480-1, 1015-2, 12617-4; ASTM C187, C305, AASHTO T129, T131, T162

The PRS-CM0075 Manual Mortar Mixer has a 5 liter (approx.) capacity, it has been designed to mix mortars and cement pastes primarily to the requirements of standards.

The mixing paddle revolves at a rate of 140 rpm. with a planetary motion of 62 rpm. in low speed. In high speed, the paddle revolves at the rate of 285 rpm. with a planetary motion of 125 rpm. The user can choose the speeds easily by using the switch fitted to the machine.

There is a sand filling apparatus on the mixer to pour sand easily. The bowl and beater are easily fitted and removed from mixer.

The Manual Mortar Mixer is supplied complete with;
â?¢ Bowl, 5 L (approx.)
â?¢ Beater

Dimensions 300x555x610 mm

Weight (approx.) 54 kg

Power 200 W

Product Code Product Description

PRS-AS0400 Ductility Testing Machine, 220-240 V 50-60 Hz

PRS-AS0420 Ductility Testing Machine with Cooling Unit, 220-240 V 50-60 Hz

PRS-AS0430 Force Ductility Testing Machine, EN 13589, 220-240 V 50-60 Hz

PRS-AS0402 Ductility Briquette Mould, ASTM D113 and AASHTO T51

PRS-AS0404 Ductility Mould Base Plate


PRS-AS0406 Ductility Mould, ASTM D6084, AASHTO T300 and EN13589 (force measurement ), Brass

PRS-AS0408 Ductility Mould, EN 13398

STANDARDS
PRS-AS0400 and PRS-AS0420 : EN 13398; ASTM D113, D6084; AASHTO T51
PRS-AS0430 : EN 13589, 13398, 13703; ASTM D113, D6084; AASHTO T51, AASHTO T300

The PRS-AS0400 Ductility Testing Machine is used to determine theductility of bituminous materials in a briquette mould by measuring the breaking elongation at a constant speed of 50 mm/min. It is designed for testing 4 specimens simultaneously. The Internal tank is made of stainless steel. The bath is fitted with an immersion heater in order to obtain (in normal conditions), the 25°C test temperature.

Each machine comprises speed control and water circulator to maintain the homogenous water temperature.

The PRS-AS0420 Ductility Testing Machine with Cooling Unit has the same specifications with PRS-AS0400 Ductility Testing Machine but with an additional cooling unit and It is not possible to convert PRS-AS0400 to PRS-AS0420 .

PRS-AS0430 Force Ductility Testing Machine has 4 loadcells. The accuracy of loadcells are ±0,1N with a maximum capacity of 300 N. The PRS-AS0430 has a cooling unit PRS-AS0430 model is equipped with TFT Graphic Display Automatic Control and Data Acquisition Unit. Failure condition can be down loaded to the Unit. Speed can be set and load-displacement curves are drawn through the software.
â?¢ Elongation measurement through motor encoder.
â?¢ 4 simultaneous load measurement with18 bit resolution.
â?¢ Speed contol with servo AC motor between 0,01 to 100 mm/min.
â?¢ Ethernet connection for computer interface.

Moulds and mould base plates should be ordered separately for all type machine.

Dimensions 300x1850x550 mm

Weight (approx.) 80 kg

Power 350 W

Manual Softening Point Apparatus (Ring and Ball Test Sets )

Product Code Product Description

PRS-AS0130 Ring and Ball Test Set, 220-240 V 50-60 Hz

PRS-AS0130/110 Ring and Ball Test Set, 110 V 60 Hz

PRSTD-1410 Hot Plate with Magnetic Stirrer

PRS-AS0131 Brass Ring, with Steel Ball and Ball Centering Guides, 2 pcs.each

PRS-AS0132 Ring Holder and Assembly

PRSGG-1330 Borosilicate Glass Beaker 600 ml

PRSGT-1305 Glass Thermometer Max. 110°C

PRSGT-1315 Glass Thermometer Max. 250°C

PRSGT-2050 ASTM 15C Thermometer -2 +80°C (IP 6OC)

PRSGT-2055 ASTM 16C Thermometer +30 + 200°C (IP 61C)

STANDARDS : EN 1427; ASTM D36; AASHTO T53

PRS-AS0130 Ring and Ball Test Set, 220-240 V 50-60 Hz The PRS-AS0130 Ring and Ball Test Set is used for determining the softening point of bituminous materials by ring and ball method.

If required, Glass Thermometer PRSGT-1305, PRSGT-1315, ASTM 15C or 16C Thermometer should be ordered separately.

The Ring and Ball Test Set is supplied complete with;

â?¢ Hot Plate with Magnetic Stirrer
â?¢ Brass Rings, 2 pcs.
â?¢ Ball Centering Guides, 2 pcs.
â?¢ Thermometer, Temperature Sensor with Holder
â?¢ Steel Balls, 9.5 mm dia., 2 pcs.
â?¢ Ring Holder and Assembly
â?¢ Borasilicate Glass Vessel Beaker 600ml

Dimensions 280x400x200 mm (packed)

Weight (approx.) 4 kg

Power 650 W

Product Code Product Description

PRS-KA0800 Slake Durability Apparatus, 220-240 V 50 Hz

PRS-KA0802 Pair of Mesh Drums for PRS-KA0800

STANDARDS : ASTM D4644

This test method has been developed to assess the deterioration of rocks over a period of time when subjected to water immersion.

Slake durability is a simulated weathering test to determine abrasion resistance during wetting and drying cycles of shale and similar soft rocks as used in embankments and other construction-related applications. Samples are alternately tumbled in mesh drums through a water medium and oven-dried for two cycles. The percent loss of mass is referred to as the slake durability index.

The PRS-KA0800 Slake Durability Apparatus consists of a motorized drive unit which is mounted on a baseplate and which can rotate two or four drums at a speed of 20 r.p.m. The tank assemblies are filled with water to a level 20 mm below the drum axis. The test drums are manufactured from 2.00 mm mesh, 140 mm dia. x 100 mm long.

Dimensions 1300x150x450 mm
Weigth (approx.) 15 kg

PRS-ZE0180 : Semi-Automatic Penetrometer for Liquid Limit, 220-240 V 50-60 Hz

PRS-ZE0180/110 : Semi-Automatic Penetrometer for Liquid Limit,110 V 60 Hz

PRS-ZE0182 : Liquid Limit Penetration Test Cone 30° Angle,Stainless Steel

PRS-ZE0183 : Cone Test Gauge for PRS-ZE0182

PRS-ZE0184 : Liquid Limit Penetration Test Cone 60° Angle,Stainless Steel

PRS-ZE0185 : Cone Test Gauge for PRS-ZE0184

PRSGH-1425 : Moisture Content Tin with Lid Ã?:55 mm x h:35 mm, Aluminum

PRSGH-1435 : Moisture Content Tin with Lid 75 mm x h:50 mm, Aluminum

A Cone Penetrometer is used to determine the moisture content at which clay soils pass from a plastic to a liquid state, and used also for the determination of undrained shear strength.
The PRS-ZE0180 Semi-Automatic Penetrometer for Liquid Limit consists of a cast iron base with course and fine leveling screws, a digital penetration measurement gauge 0.01 mm resolution/readibility and an automatic penetration timer unit.

The PRS-ZE0180 is equipped with a digital, 99 second timer, which can be set to the standard 5 second free-fall time or to some other setting for customized tests. When engaged the timer will allow the needle to free fall into the sample for the specific time interval and then lock the needle from advancing while providing a direct reading of the test results. 320 g weight should be added to the 30° angle cone to get a total weight of 400 g for the shear strength test.

Semi-Automatic Penetrometer for Liquid Limit supplied complete with;
Automatic Penetration Timer Unit,
30° Penetration Cone
Sample Cups, 3 pcs. Aluminium, Ã?55 mm x h:35 mm.

Product Code : Product Description

PRS-ZE0665 : Spring Type Proctor Penetrometer

PRS-ZE0666 : Needle Set for Proctor Penetrometer

(28.55, 24.79, 20.22, 16.54, 12.83, 9.07, 6.40, 5.23 and 4.52 mm diameters)

The PRS-ZE0665 Spring Type Proctor Penetrometer is used for establishing the moisture-penetration resistance relation of finegrained soils. The apparatus consists of a spring loading device which is graduated from 10 to150 lbf in 2 lbf subdivisions.

Needle Set for Proctor Penetrometer consist of interchangeable needle points of 28.55, 24.79, 20.22, 16.54, 12.83, 9.07, 6.40, 5.23, 4.52 mm diameters and a carrying case.

Dimensions : 540x260x60 mm (packed)
Weight (approx.) : 5 kg

Product Code Product Description

PRSD-1295 Laboratory Oven 50 lt., 220-240 V 50-60 Hz

PRSD -1300 Laboratory Oven 120 lt., 220-240 V 50-60 Hz

PRSD -1305 Laboratory Oven 250 lt., 220-240 V 50-60 Hz

PRSD -1310 Laboratory Oven 500 lt., 380 V 50 Hz

PRSD -1315 Laboratory Oven 700 lt., 380 V 50 Hz

STANDARDS: EN 932-5, 1097-5; ASTM C127, C136, D558, D559, D560, D698, D1557, D1559 BS 1377:1, 1924:11; UNE 103300


PARSROS * PRSD Series Laboratory Ovens have been designed for drying asphalt, soil, rock, concrete, aggregate or similar materials. 50, 120, 250, 500 and 750 liter capacity models are available. Temperature range is from ambient to 200°C. The interior is manufactured from stainless steel and the exterior is robustly constructed from sheet steel finished in powder coated paint.

All models are fan circulated (forced convection), fitted with direct reading digital control unit and equipped with an analogue overtemperature protection thermostat. Laboratory Ovens are supplied complete with 2, 3, 4 or 5 shelves according to the capacity.

Product Code Internal Dimension External Dimension Weight (approx.)

PRSD-1295 410x350x360 mm 580x600x570 mm 20 kg

PRSD -1300 610x500x400 mm 770x750x650 mm 56 kg

PRSD -1305 800x600x570 mm 970x840x790 mm 85 kg

PRSD -1310 1100x790x580 mm 1401x920x770 mm 130 kg

PRSD -1315 1400x890x570 mm 1600x1130x770 mm 170 k

Product Code Product Description

PRS-KA0555 Hoek Triaxial Cell BX, 42.04 mm dia.

PRS-KA0556 Spare Sealing Sleeves for Hoek Triaxial Cell BX

PRS-KA0557 Hoek Triaxial Cell NX, 54.7 mm dia.

PRS-KA0558 Spare Sealing Sleeves for Hoek Triaxial Cell NX

PRS-KA0560 Hoek Triaxial Cell HQ, (Ã? 63,5 mm)

PRS-KA0561 Spare Sealing Sleeves HQ, (Ã? 63,5 mm) for Hoek Triaxial Cell

Hoek Cells have been designed to be used for triaxial testing of rock specimens.
Hoek Cells comprise a steel body complete with two quick release self-sealing couplings, two steel end caps which are screwed to the cell body, 2 pieces of upper and 2 pieces of lower loading caps with spherical coupling and a rubber sealing sleeve to separate the specimen from the cell fluid.

Dimensions 350x150x200 mm

Weigth (approx.) 15 kg

Product Code Product Description

PRS-B0510Concrete Flow Table Test Set

PRS-B0512Flow Cone for PRS-B0510

PRS-B0513Wooden Tamper 40x40x335 mm

The test set is used for concrete mixes of high workability and determines flow index as an arithmetic mean of the diameter of the specimen after working on a flow table.

The apparatus consists of a double steel table, an upper table measuring 700x700 mm and hinged at one side to the lower table.

The top table is inscribed and all parts are protected against corrosion. The stainless steel cone has a 130 ±2 mm top diameter, 200 ±2 mm base diameter and 200 ±2 mm height and 1.5 mm thickness.

Dimensions700x850x300 mm

Weight (approx.)40 kg

The Concrete Flow Table is supplied complete with;
â?¢Flow Cone
â?¢Wooden Tamper

Product Code : Product Description

PRS-B1010 : Universal Cutting Machine Small, 380 V

PRS-B1020 : Universal Cutting Machine Junior, 380 V

PRS-B1030 : Universal Cutting Machine Major, 380 V

PRS-B1012 : Cutting Blade Ã? 350 mm

PRS-B1022 : Cutting Blade Ã? 450 mm

PRS-B1032 : Cutting Blade Ã? 600 mm

The PARSROS Series Universal Cutting Machines have been developed to cut and prepare concrete, rock or natural stone cores or other type test specimens. It is available in three different models.

Special clamp assembly allows specimens to be held during cutting operation. The machine is supplied complete with â??Vâ?? block clamp for Ã? 100 mm specimens and a water circulation pump.

If 220 V is requiered please mension at time of order.

Cutting Blade should be ordered separately.

Four Column Automatic Compression Testing Machines

Product Code Product Description

PRS-B52312000 kN Automatic Four Column Compression Testing Machine EN 220-240 V 50-60 Hz

PRS-B53313000 kN Automatic Four Column Compression Testing Machine EN 220-240 V 50-60 Hz

PRS-B54314000 kN Automatic Four Column Compression Testing Machine EN 220-240 V 50-60 Hz

PRS-B55315000 kN Automatic Four Column Compression Testing Machine EN 220-240 V 50-60 Hz

PRS-B0210High Precision Pressure Transducer and Electronic


PRS-B5231 and PRS-B5331 Testing Machine is supplied complete with;

Ã? 205x90 mm, Ã? 205x50 mm and Ã? 205x30 mm distance pieces

PRS-B4513 Upper Platen (with ball seating assembly) Ã?300 mm, Lower Platen Ã?300 mm.
PRS-B4510, PRS-B4511, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B5231 and PRS-B5331 testing machines.

PRS-B5431 and PRS-B5531 Compression Testing Machines are supplied complete with;

2 pcs. Ã? 205x90 mm, 2 pcs. Ã? 205x50 mm and 2 pcs. Ã? 205x30 mm distance pieces

PRS-B4513 Upper Platen (with ball seating assembly) Ã?300 mm, Lower Platen Ã?300 mm.
PRS-B4510, PRS-4511, PRS-B4512 and PRS-B4515 upper and lower platen sets can also be used with PRS-B4531 and PRS-B5531 Testing Machines

Automatic Grinding Machine

Product Code Product Description
PRS-1040Automatic Grinding Machine, 220-240 V 50-60 Hz

PRS-1042Grinding Wheel PRS-1035 and PRS-1040

PRS-1043Cradle for Ã?:38-100 mm Cylindrical Specimens

PRS-1044Water Restraint Panel Set

PRS-1048Water Restraint Panel for dia 160mm Cylinder Specimen

Product Code : Product Description

PRS-B0950 Large Metal Curing Tank

PRS-B0952 Set of Removable Upper Racks for PRS-B0950

PRS-B0954/NCuring Tank Heater for PRS-B0950 and PRS-B0965, 220-240 V 50-60 Hz (3 cm connecting channel and 50 cm resistance length)

PRS-B0955 Circulating Pump, 220-240 V 50-60 Hz

PRS-B0960 Large Plastic Curing Tank

PRS-B0962 Wide Plastic Curing Tank

PRS-B0956 Curing Tank Heater for PRS-B0960 and PRS-B0962 , 220-240 V 50-60 Hz (6,5 cm connecting channel and 70 cm resistance length)

(If 110V required please indicate on your order)

The PRS-B0950 steel, PRS-B0960 and PRS-B0962 Plastic Curing Tanks are designed for curing concrete cubes and cylinders. The temperature can be adjusted and can be kept constant by an electric resistance incorporating a digital thermo regulator which maintains the set temperature between ambient to 40 ºC with ± 2 ºC accuracy.

The PRS-B0950 is manufactured from powder coated sheet steel. Suitable upper racks to hold concrete cubes are available on request (max. 8 pieces). PRS-B0960 and PRS-B0962 tanks have a bearer metal carcass.

The PRS-B0952 should be ordered separately.

All Curing Tanks are supplied complete with;

Heater

Submersible Circulation Pump

Base Metal Racks

Freezing and Thawing Chamber

Product Code Product Description

PRSD-1440 Freezing and Thawing Chamber 285 L, 220-240 V 50-60 Hz

STANDARDS : EN 1338, 1339, 1340, 1367-1, 1367-6, 12371, 13748-2, 13450; CEN/TS 12390-9

It is used for the determination of resistance to freezing and thawing by providing freezing / thawing in air. The chamber is equipped with a user defined program including 10 steps. Time can be adjusted to 999 minutes for each step of the program. The temperature range of the cabinet is -30°C to +30°C.

The temperature is controlled by a sensor which can be immersed either into the sample, into the water which the sample is placed into or, into the salty water solution placed on the sample before starting the test. The calibration of the sensor is carried out using the user friendly menu.

The cabinet provides maximum cooling 5A°C/hour and maximum heating 10°C/hour. The distribution of temperature in the cabinet is performed using the integral fan. Software for data transfer to a computer is supplied complete with the cabinet, and data can be monitored during the tests. Data can be converted to an excel report or to a graph.

The condenser of the cabinet is fitted with an air cooled hermetic cooler. The gas used for the cooler does not include CFCâ??s.

Internal Dimensions 490x530x1100 mm

External Dimensions 690x860x1940 mm

Weight (approx.) 225 kg

Power 1800 W

Moisture Balance

Product Code Product Description

PRSW-0610 Moisture Balance 50 g x 0.001 g

The PRSW-0610 Moisture Balance is specially designed to determine the moisture content of relatively small samples of various substances.

Features

Easy operation provided by backlit LCD display
Drying profile (standard mild step rapid)
Finish mode (manual humidity stabilization automatic time defined)
GLP/GMP printouts and reports
Halogen lamp
Standard and non-standard applications
Optimization of work ensured by halogen lamps mode

Capacity 50 g

Pan Size Ã? 90 mm

Readability 1 mg

Maximum Sample Mass 50 g

Moisture Reading Accuracy 0.001 %

Repeatability ± 0.24% (sample < 2 g)

± 0.06% (sample 2-10 g)

± 0.04% (sample > 10 g)

Maximum Drying Temp. 160°C

Drying Modes 4 Modes: Standard / Quick / Step / Mild

Power of Heater 400 W

Power Supply 110-240 V 50-60 Hz AC

Display LCD (backlit)

Dimensions 210x335x190 mm

Weight (approx.) 5 kg

PRSM-4000 : Hydraulic Universal Testing Machine,600 kN, 220-240V

PRSM-4000/110 : Hydraulic Universal Testing Machine, 600 kN, 110V

PRSM-4001 : Frame for 600 kN Hydraulic Universal Testing Machine

PRSM-4002 : Hydraulic Grips Jaw Faces Set for Round Specimens

PRSM-4003 : Hydraulic Grips Jaw Faces Set for Flat Specimens

PRSM-0500 : Extensometer for Universal Testing Machine, 50 mm Gauge Length (Accuracy 0.01 mm),

PRSM-0510 : Extensometer for Universal Testing Machine, 100 mm Gauge Length (Accuracy 0.01 mm)

PRSM-0520 : Extensometer for Universal Testing Machine, 50 mm Gauge Length (Accuracy 0.001 mm)

PRSM-4000 Universal Hydraulic Tensile Test Machine is designed to test the ferrous materials for structural values such as yield strength and tensile strength. Apart from tensile tests, Universal Test Machines can also be used for compression tests up to the capacity of the machine.

Maximum security is maintained on 600kN capacity Universal Test Machine by limit switch on the lower grip and piston as well as the safety check valves on the hydraulic system. Hydraulic power unit works silently.0-40 mm flat and 8-32 mm round samples can be tested with a user friendly hydraulic jaws that comply with standards.

Load cell is used for load measurements. Strain measurement is done by the electronic displacement transducer built in the machine if required external extensometer fitted to the specimen also can be used for strain measurement. Strain measurements can be done directly from the extensometer fitted to the specimen.

Tests can be done fully automatic by digital control unit or computer. Machine complete the test with the set pace rate and turns to start position automatically.

PRSM-4000 Hydraulic Universal Testing Machine, features two test spaces for tension tests and compression tests. User can quickly change between tension and compression testing without having to remove heavy fixtures. This flexible design also helps to ensure safety, reduces operator effort and improves productivity.

The distance between the grips can be set by motor driven hand set system. With open front hydraulic wedge grips user can load specimen easily.

Product Code : Product Description

PRS-ZE0852 : CBR Test Machine with Load Ring, 50 kN capacity, 220-240 V 50-60 Hz

PRS-ZE0852/110 : CBR Test Machine with Load Ring, 50 kN capacity, 110 V 60 Hz

STANDARDS

NF P94-078; UNI CNR 10009

The PRS-ZE0852 is designed for performing laboratory evaluation of the CBR value of highway sub bases and subgrade and for the determination of strength of cohesive materials which have maximum particle sizes less than 19 mm (3/4â?).

The PRS-ZE0852 is designed to load the penetration piston into the soil sample at a constant rate to measure the applied load and piston penetration at predetermined intervals.

The machine is designed to be mounted on a suitable bench and comprises of a robust and compact two column frame with adjustable upper cross beam. The frame has 50 kN capacity.

Two test speeds are provided 1.0 mm/min for BS and 1.27 mm/min. for ASTM/EN/AASHTO tests. This main feature allows the user to perform tests complying to BS or ASTM/EN/AASHTO standards with the same machine. Loading and unloading are down from the front panel by UP/DOWN buttons. Unloading speed is udjusted 5 mm/min for easy re-testing.


The CBR Test Machine is supplied complete with;
Load Ring, 50 kN
Digital Gauge with Connection Part, 25x0.01 mm
Penetration Piston

PRS-B0980 Accelerated Curing Tank, Ambient to +60°C, 380 V 50 Hz

PRS-B0980 Accelerated Curing Tank is designed for curing concrete specimens according to ASTM C1768 (Procedure A - Warm Water Method) and BS 1881:Part 112 (35°C Method and 55°C Method).

The Tank consists of an insulated rectangular double walled metal chamber inside lined with stainless steel outer powder coated, an insulated lid with lifting handle to cover the chamber and an stainless steel perforated platform for circulation of water and to support the concrete specimes The tank also has a circulation pomp. to provide the same water temperature at any point within the tank.

The tank works ambient to +60°C temperature. The temperature is controlled with closed loop PID controlled digital thermoregulator with accuracy of ±2°C. Curing temperature and curing time can also be set.

Product Code Product Description

PRS-B1050 Melting Pot 3 lt. Capacity, 220-240 V 50-60 Hz

PRS-B1050/110 Melting Pot 3 lt. Capacity, 110 V 60 Hz


The PRS-B1050 melting pot is used for melting the capping compound. The apparatus consists of a 3 litre capacity aluminium container in a well-lagged steel jacket, cover and thermostatic control heating system to keep the temperature constant in the range of ambient to 200 ºC.

Dimensions350x320x290 mm
Weight (approx.)9 kg
Power600 W

Product Code Product Description

PRS-B0750 Concrete Mixer Pan Type, 100 L, 220-240 V 50-60 Hz

The efficient mixing of concrete is essential if quality specimens are to be manufactured.The Pan Type Concrete Mixers is designed to give efficient mixing of both dry and wet materials.

The mixing pan is removable and tilts for easy access to the pan and emptying on completion of the mixing operation. The total volume of the pan is 100 liters but the effective capacity of the mixer is 56 liters.

The mixer head lifts clear to provide maximum access to the pan and holds the mixing blades at a constant depth during the mixing operation. The blades can be adjusted to suit the different types and volume of materials to be mixed. The pan type mixer is also equipped with rubber wheels which provide high portability.

All parts of the IP55 protected mixer are noncorrosive painted and galvanized.

Product Code PRS-B0750

Dimensions 950x1050x1250 mm

Weight (approx.)255 kg

Power1500 W

Product Code Product Description

PRS-1035Semi-Automatic Grinding Machine, 220-240 V 50-60 Hz

PRS-1042Grinding Wheel for PRS-1035 and PRS-1040

PRS-1043Cradle for Ã?:38-100 mm Cylindrical Specimens

PRS-1044Water Restraint Panel Set

PRS-1048Water Restraint Panel for Ã?160mm Cylinder Specimen

The PRS-1035 Semi-Automatic Grinding Machine provides fast grinding of cylinder specimen ends to obtain plane and parallel surfaces according to EN and ASTM standards.

The ony differance between automatic machine and semi-automatic machie is that the cradle of the semi-automatic machine is moved toward the grinding wheel by user. All grinding process is automatic except the movement of the cradle for semi-automatic machine. The optimum cycle to be applied by user is 5-6 cycle/per minute.

The machine is manufactured from stainless steel for resistance to corrosion. The water restraint panels should be ordered seperately for cubic specimens or different sized cylindrical specimens.


The Semi-Automatic Grinding Machine is supplied complete with;

The preparation of concrete cylinder test specimen for compressive strength testEN 12390-1, 12390-3 ASTM C31, C39, C192, C617

The maximum tolerance on the flatness of the potential load bearing surfaces (the ends of compression test specimens) is 0.002 in. [0.050 mm]

The preparation of drilled concrete cores specimen for compressive strength testEN 12504-1, 12390-1, 12390-3 ASTM C42, C397

The deviation of perpendicularity of the side, with reference to O the end faces is 0,5O

â?¢Grinding Wheel for concrete specimens

â?¢Cradle for Ã?:38mm to100 mm cylindrical specimens

â?¢Water restraint panel set f (Consist of four panels Ã?150, 100, 75 and 50 mm)

Dimensions730x1200x1500 mm

Weight (approx.)280 kg

Power1850 W

Aggregate Impact Value (AIV) Testing Apparatus

Product Code Product Description

PRS-A0650 Aggregate Impact Value (AIV) Testing Apparatus

The Aggregate Impact Value Testing Apparatus, meets with BS 812, it is robustly designed to determine the Aggregate Impact Value (AIV) of aggregates which provides a relative measure of the resistance of an aggregate to sudden shock or impact.

The counter fitted to the machine automatically records the number of blows delivered to the sample, manufactured from heavy duty plated steel to resist corrosion.

The Aggregate Impact Value (AIV) Apparatus is supplied complete with;
Cylindrical Measure, 75 mm,
Steel Tamping Rod, 16x600 mm

Dimensions 450x350x850 mm

Weight (approx.) 52 kg

Air Contents

Product CodeProduct Description

PRS-B0650Air Entrainment Meter

PRS-B0652Manometer for PRS-B0650

PRS-B0408Tamping Rod 16x600 mm

PRS-0714Straight Edge 300x30x3 mm


Standards : EN 12350 ASTM C231; AASHTO T152

PRS-B0650 Air Entrainment Meter is used to determine the air content of fresh concrete. It consists of a flanged 7 liter capacity cylindrical vessel and cover assembly incorporating a large (90 mm dia.) pressure gauge, air pump and valves. It has a quick action clamping system.

Direct pressure gauge reading to the nearest 0.1% up to 6% and 0.2% from 6 to 10%. It is not affected by changes in barometric pressure.

The meter measures up to 22% of entrained air. It is appropriate for aggregates size of maximum 63 mm.

The Air Entrainment Meter is supplied complete with;

Straight Edge

Tamping Rod

Wash Bottle. 250cc J-Type pipe and an inner extension pipe for calibration
Special Carrying Case

Capacity7 litres

Air Content Range0-10%

Graduations0.1% up to 6&; 0.2% from 6 to %10

Dimensions300x310x620 mm

Weight (approx.)16 kg

Water Impermeability Tester ( 3 Unit )

Product Code Product Description

PRS-BWIT3 Water impermeability Tester ( 3 Unit )

STANDARDS : TS EN 12390-8,EN 12364,DIN 1048,ISO 7031

Apparatus at 3 or 6 points to determine the depth of penetration of the water into the concrete (impermeability) under known time and pressure The unit accepts up to 3 concrete cubic, cylindrical or prismatic specimens having max. dimensions of 200x200x200 mm

The specimen is put into the test chamber, clamped with suitable flanges and gaskets, and then a known water pressure is applied on the specimenâ??s surface for a time as requested by Standard, by using a suitable air compressor (accessory) having at least 5 or 20 bar pressure capacity

The water penetrated is measured by breaking the specimen, or by reading the water permeated through the graduated burette fixed on the front panel

Dimension 1290 x 450 x 1280 mm

Weight 120 kg (app.)

Digital Balances

Product Code Product Description

PRSW-0633 Digital Balance 600 g x 0.01 g

PRSW-0635 Digital Balance 6 kg x 0.1 g

PRSW-0637 Digital Balance 30 kg x 5 g

PRSW-0638 Digital Balance 30 kg x 0.5 g

PRSW-0640 Digital Balance 3000 g x 0.01 g

PRSW-0642 Digital Balance 3500 g x 0.01 g

PRSW-0643 Dijital Terazi 4500 g x 0.01 g

PRSW-0645 Digital Balance 15 kg x 0.2 g

PRSW-0648 Digital Balance 30 kg x 0.1 g

PRSW-0654 Digital Balance 60 kg x 1 g

The PARSROS Series Digital Balances provide a wide range of maximum capacity and readability characteristics which make them economical and easy to use, they are ideal for central and site laboratories who require a range of balances for various applications.

The PARSROS Series Digital Balances are fitted with strain gauge load cells and are designed with large backlit LCD displays that give precise measurements within the 0°C to 40°C temperature range. Digital Balances have an internal automatic calibration feature. All models can be connected to printers or PC's through their RS 232 outputs and are supplied with 220-240 V, 50-60 Hz AC/DC adapters.


Product Code Capacity Readability Pan Size Power Supply

PRSW-0633 600 g 0.01 g 16 mm AC Battery

PRSW-0635 6 kg 0.1 g 300x230 mm Rechargeable Batt.

PRSW-0637 30 kg 5 g 300x230 mm Reachargeable Batt.

PRSW-0638 30 kg 0.5 g 300x230 mm Reachargeable Batt.

PRSW-0640 3000 g 0.01 g 125x145 mm Reachargeable Batt.

PRSW-0642 3500 g 0.01 g 300x230 mm Electrical

PRSW-0643 4500 g 0.01 g 195x195 mm Electrical

PRSW-0645 6000 g 0.01 g 195x195 mm Electrical

PRSW-0648 15 kg 0.2 g 300x230 mm Reachargeable Batt.

PRSW-0654 30 kg 0.1 g 310x220 mm Reachargeable Batt.

Digital Hot Plates

Product Code Product Description

PRSD-1400 Digital Hot Plate 300x300 mm, 220-240 V 50-60 Hz

PRSD-1402 Digital Hot Plate 350x450 mm, 220-240 V 50-60 Hz

PRSD-1403 Digital Hot Plate 400x600 mm, 220-240 V 50-60 Hz

PRSD-1405 Hot Plate Ã? 170 mm 220-240 V 50-60 Hz

PRSD-1410 Digital Hot Plate with Magnetic Stirrer 220-240 V 50-60 Hz


Product Code PRSD-1400 PRSD-1402 PRSD-1403

Temperature Range Ambient to 350OC

Control System Digital Thermostat

Temperature Sensivity ± 2 OC

Plate Dimensions 300x300 mm 300x450 mm 400x600 mm

External Chamber Electrostatic Powder Paint, Steel


Product Code PRSD-1405

Plate Dimensions 170 mm

Hot Plate Type Sanding Plate

External Chamber Electrostatic Powder Paint, Steel

Product Code PRSD-1410

Temperature Range Ambient to 300OC

Stirring Speed 100-2000 r.p.m.

Stirring Capacity 5000 ml

Plate Dimensions 190x190 mm

External Chamber Electrostatic Powder Paint, Steel

Product Code Dimension Weight (approx.) Power

PRSD-1400 300x300x250 mm 3.5 kg 1200 W

PRSD-1402 350x450x250 mm 5.5 kg 1800 W

PRSD-1403 400x600x250 mm 7.5 kg 3000 W

PRSD-1405 300x300x200 mm 2.5 kg 1500 W

PRSD-1410 210x310x100 mm 2.8 kg 600 W

Microwave Oven

Product Code Product Description

PRSD-1420 Microwave Oven 19 lt., 220-240 V 50-60 Hz

The PRSD-1420 Microwave Oven is used for drying, conditioning, moisture determination and pre-heating applications when quick drying is required.

The PRSD-1420 has max. 250°C, 100 min. program timer, rotating tray system, 2000 W

Capacity 19 litres

Working Frequency 2450 Mhz

Internal Dimensions 210x295x315 mm

External Dimensions 50x300x300 mm

Weigth (approx.) 11 kg

Power 2000 W