Power Recording Analyzer is designed for power signal record. The power generator test items are integrated at the tester. With those test items users can make motor (Power generator) No-load test, Short circuit test, Motor excitation step response test, motor excitatory de-excitation test, motor load rejection test and grid synchronous connection test and also on
Technique index ~200V, -400V~400V and -20mA~20mA. Users can switch the input range from software. Also there is one channel -100mV~100mV which allow the input signal less than 10V.
2. The voltage and current input range assured errors are as follow:
-400V~ 400V assured error less than 0.5V
-200V~ 200V assured error less than 0.2V
-10V~ 10V assured error less than 0.01V
-20mA~ 20mA assured error less than 0.02mA
-100mV~ 100mV assured error less than 0.2mV
3. There are 12 channel wet contacts binary signal input. The valid and allowed input voltage is DC12-200V.
4. There are 3 channel relay contacts output. The maximum capacity for the contacts is AC220V/1A.
5. There are 2 USB port used for data export and mouse/keyboard input
6. The LCD is 12.1 inches touch pad input mode. Make the human interface more simple.
7. The saved space in the tester is 32G for standard configuration
8. Input resistances for different channels are as follow:
As a manufacturer and a supplier we produce cementing tools since 1997, and now we have almost 400 workers, the products cover cementing head/plug, stage collar, float equipment, centralizer and so on. Please contact me if you have need, and my email is
Automatic tension tester Intermolecular Forces formed liquid surface tension.Numbers of tension reflect on liquid sampleâ??s physics and chemical properties, it is one of the most important index to product quality. automatic interfacial tension tester apply to GB/T6541,it can test kinds of liquid surface tension and boundary surface tesion.this method sample and accuracy,so its used widely
3 phase transformer on-load tap changer testeris mainly used to test three-phase transient time, transition waveform, transition resistance, synchronization state, etc. The transformer on-load switch tester is a comprehensive transformer on-load switch measurement and tester, which is used to measure and analyze the electrical performance indicators of power transformers and special transformers on-load tap-changers. The transformer on-load switch tester can automatically capture and display the transition resistance during the transition process. There is also a process of time jumping.
Technical parameters
Three phase constant current source charge,charge current: 3A/1A; 0.6A/0.2A
Maximum voltage of the port: 24V
Maximum range of transition resistance: 100
Measuring range: 1A 0.4 20 0.2A 10 100
Record time of waveform:300ms
Sample rate: 30k
Resolution of time:0.1ms
Resolution of resistance: 0.1
Accuracy of transition resistance: ±5% Reading±0.1
As a manufacturer and a supplier we produce cementing tools since 1997, and now we have almost 400 workers, the products cover cementing head/plug, stage collar, float equipment, centralizer and so on. Please contact me if you have need, and my email is
15262 Tools Instruments Suppliers
Short on time? Let Tools Instruments sellers contact you.
CASfire Technical Co.,Ltd have rich experience to provide FAR 25.853 Vertical Flammability Test for Aircraft Material
FAR 25.853 Vertical Flammability Test for Aircraft Material- Standard
Far 25.853: Fire Protection for compartment interior
FAR 25.853 fire test to aircraft material - Vertical Test
FAR 25.853 vertical test - Brief
The test apparatus are almost same to UL94V and test the performance of self-extinguish of material under fire condition.
FAR 25.853 vertical test - Test method
The samples is 76mm width and is placed vertically, the ignition resource is same to horizontal test. The burner apply 60s or 12s
The following result will be recorded
- Burning length
- Flame time
- Dropping time
FAR 25.853 Vertical Flammability Test for Aircraft Material- other standards
Airbus standard: ABD 0031- airbus fire testing - flame, smoke and toxicity
Boeing Standard: BSS 7238 fire testing to smoke density
Boeing Standard: BSS 7239 fire testing to toxicity
ASTM Standard: ASTM E 662 fire testing to Smoke Density
FAR 25.853 Fire test to aircraft material - Test method
Vertical flammability test: 14 FAR 25.853 b(4)), (App. F to part 25 part I (a)
Smoke Density Test: 14 FAR 25.853 (d), (App. F to part 25, part V)
Heat Release Test: 14 FAR 25.853 (d), Appendix F, Part IV
Seat Test: 14 FAR 25.853 (c, App.F to part II)
Horizontal Test: 14 FAR 25.853 b(2,3), (App. F to part 25 part I (a),(1)
45 flammability test: 14 FAR 25.853 (b), (App. F to part 25, part I (6))
CASfire Technical Co.,Ltd have rich experience to provide BSS 7239 Toxicity Test to Aircraft Material
BSS 7239 Toxicity Test to Aircraft material
BSS 7239: Test method for toxic gas generation by materials on combustion
BSS 7239 Toxicity Test to Aircraft material - Brief
Gases produced for analysis are generated in a specified, calibrated smoke chamber during standard rate of smoke generation testing (ASTM E 662), in both flaming combustion and non-flaming pyrolytic decomposition test modes
BSS 7239 Toxicity Test to Aircraft material- Gases measured
The following gases are required to be measured by this test standard
CO Carbon monoxide
HF Hydrogen Fluoride
HCl Hydrogen chloride
NOx Nitrogen oxides (Both NO, nitric oxide, and NO2, Nitrogen dioxide, are detected)
SO2 Sulfur dioxide
HCN Hydrogen cyanide
Fire test to aircraft material relative standards
FAR 25.853 flammability test to aircraft material
Air bus standard ABD 0031 - airbus fire testing â?? flame, smoke and toxicity
Boeing Standard BSS 7238 fire testing to smoke density
Boeing Standard BSS 7239 fire testing to toxicity
ASTM Standard ASTM E 662 fire testing to Smoke Density
ASTM Standard ASTM E 162 Surface Flammability of materials
Xiamen Zhongxinda Hydrogen Technology Co., Ltd. has been specialized in the design, R & D, manufacture and sales of water electrolysis hydrogen production equipment, hydrogen storage equipment, hydrogen bus bar and hydrogen purification device in various industries for many years.
The hydrogen production capacity of the equipment produced by our company ranges from 5Nm3/h to 1000Nm3/h.The hydrogen energy equipment of by-product hydrogen tail gas, peak shaving and frequency regulation of thermal power plant provide the design, production, installation and commissioning of hydrogen production, hydrogen storage, hydrogen production and hydrogenation station and technical services.
Hydrogen production: 5M3 / NH
Oxygen production: 2.5m3/nh
Hydrogen purity: 99.99%
Oxygen purity: 99.2%
Dew point: 70
System working pressure: 1.6 ~ 3.2Mpa
Working temperature of electrolyzer: 80 85
Rated working current of electrolytic cell: dc500a
Rated working voltage of electrolytic cell: DC48V
Unit power consumption: 4.8KW. H / n.m3
Product description AC DC high voltage dividerFRC series AC DC high voltage divider also known as FRC Divider, it is a kind of resistance-capacitance equivalent potential screen voltage division type high voltage measurement device, is mainly used for the measurement of pulsed high voltage, lightning high voltage and power frequency high voltage. It is the first choice for the replacement of high voltage electrostatic voltmeter.
The Intelligent Tg dielectric loss tester is equipped with high voltage step-up transformer. Besides, it takes security measures like zero-cross closing, lightning protection, etc. During the experiment, different levels of high voltage ranging from 0.5KV to 10kV are outputted. The instrument has the advantages of convenient and safe operation.
Technical index
The Intelligent Tg dielectric loss tester has: printer, keyboard, indicator and communication transmission.
Detect internal standard capacitor current: 10�¼A~1A
Used to determine the permeability coefficient of the soil, The whole system is compact. Reasonable design, Convenient to disassemble and assemble, equable stress (use the hand wheel to do the rotary extrusion in the center). All accessories made of high quality cuprum except frame. There are two Position-limit flight of steps on the protective ring, during the process of pack stop-hydrosphere, not only assure the sample will not hang, but also protect cutting ring and control the deformation degree of rubber ring.
Constant Head Soil Permeameter is used to determine the penetration coefficient when the sand soil and the incoherence soil which has few broken-stones to carry on the permeability test under constant head.
Designed to provide reliable results from a unit which is compact without sacrificing accuracy and repeatability. It comes with triple beam ratio and compact design ensures space saving.
It is used in soil compression test to detect the relationship between soil pressure and deformation, calculate the unit deposition, compression index, resilience index and consolidation coefficient of soil, etc.
The stainless steel peat sampler is in fact a kind of gouge auger. The peat sampler is pushed into the soil manually. The sample containing part is a half cylinder. The peat sampler distinguishes itself from the standard gouge auger as its cone is massive.
The sample containing section is sealed off by a plate (fin) that can pivot around the axle in the middle of the sampler and that is fitted with a cutting edge on one side. Having arrived at the correct sampling depth the complete sampler is given half a turn clockwise (180). During the turning the fin remains in position which allows the half cylinder to be filled and closed again.
The half circular sample cylinder is kept closed by the other side of the fin during extraction.
Usage: Used for checking the compressive strength of lime soil.
Standard: BS 1377:7, ASTM D2166, AASHTO T208
Technical Specifications:
Maximum load 50KN
Lead screw disc diameter 52mm
Up speed 3mm/min
Maximum load 50KN
Lead screw travel distance 50mm
Voltage 220v
Overall dimensions 40x35x80CM
