Applications:
1. Filter material Gas filter: medical masks, room air conditioners filter material Liquid filter: beverage filtration, water filtration
2. Medical & Health Material Surgical Mask: inner and outer layers with spunbond material, in the middle is melt blown fabric.
3. Environmental protection material (oil absorbent material) Meltblown nonwovens used mainly PP material. It can absorb 17-20 times bigger than its own weight of oil, in environmental protection, you can make absorption felt, oil filter, etc., are widely used in marine oil spill, plant equipment ,sewage treatment and so on.
4.Clothing Materials meltblown nonwovens by the microfiber into a net, so its very soft feel. And the fabric of small aperture, high porosity, with very good wind resistance and good air permeability, light weight, is currently doing the best material for clothing insulation materials.
Lump sulfur, also known as granular or rock sulfur, is typically characterized by a purity of 99.80% or higher, with a maximum ash content of 0.05%.
It should also have a limited acidity (H2SO4) of 0.02% or 0.03% and minimal moisture content (0.5% or 0.2%).
More detailed breakdown of lump sulfur specifications:
Purity:
Dry Basis: 99.80% minimum purity is a common specification.
Other Standards: Some standards like Refinery Specifications, may specify a purity of 99.98%.
Impurities:
Ash Content: A maximum ash content of 0.05% is a typical requirement.
Acidity: A maximum acidity (H2SO4) of 0.02% or 0.03% is common.
Organic Substances: Some specifications limit organic substances to 0.01% or 0.03% maximum.
Moisture: A maximum moisture content of 0.5% or 0.2% is generally specified.
Mechanical Impurities: Some specifications require the absence of mechanical impurities like paper, wood, or sand.
Other Impurities: Some standards specify limits for arsenic, selenium, tellurium, and lead impurities.
Color and Appearance:
Color: Bright yellow is the typical color specification.
Other Considerations:
Test Methods:
Specifications often include test methods, such as ASTM D-4239, ASTM D-1509, ASTM D-1613, and ASTM D-2790, for determining the various parameters.
Bulk Density:
Granular sulfur has a bulk density of around 70 lb/cu ft (1121.29 kg/cu m).
Solubility:
Sulfur is insoluble in water, partially soluble in acetone, and slightly soluble in diethyl ether and alcohol.
Keep away from heat, hot surfaces, Sparks, Open flames and other ignition sources. No smoking. Proper
grounding procedures to avoid static electricity should be followed. Prevent dust accumulation (to minimize
explosion hazard). Avoid generating dust.
Other Hazards:
It contains a small amount of Hydrogen Sulfide. Hydrogen sulfide is a fatal and highly flammable gas with a
rotten egg odor that quickly causes odor fatigue. Heating of this product and storage under elevated
temperatures or over long periods of time may release higher amounts of Hydrogen Sulfide. Hydrogen
Sulfide is also an asphyxiant. Exposure may aggravate preâ??existing eye, skin, or respiratory conditions.
Storage:
(1) Prevent from moisture absorption, keep away from heat, keep in air well â?? ventilated area.
(2) Do not contact with acids and alkaline substance, protect from dust.
(3) Ensure bags are kept in sealed and in good condition.
Packing:
The packing is in 50/Kg. bags, Jumbo Bag 1/MT or in Bulk.
Spcification of Sulfur:
Color: Bright yellow when solid (No dark particles visible)
Purity: 99.8% by weight minimum, dry basis. Sulfur Content: 10ppm by weight, maximum (0.01%)
Moisture Content: 0.50% by weight maximum
Ash: 300ppm by weight, maximum (0.03%)
Organic matter: 500ppm by weight, maximum (0.05%)
Size: 2mm â?? 6mm
Bulk Density: Minimum 1040 Kg/m3 (loose)
Bulk Density: Minimum 1200 Kh/m3 (packed)
Acidity as H2SO4: 50ppm by weight, maximum (0.005%)
For Price Quotation, please fee free to reach out to us, price reflected on page is for show only.
COMPOSITION SPECIFICATION
Nitrogen 46.0% by Weight Min.
Moisture 0.5% Max.
Biuret 1% Max. by Weight
Fisper 0.35 Max.
Anti Caking Agent 0.5% Max.
Free Ammonia 160 PXT PPM Max.
Granulation 2 4 mm: 90% Min.
Dimension Less than 1 mm: Absence
Melting Point 132 C
Color Pure White
Physical Specification
Non clotted 100% free from harmful substances.
Internationally accepted standard for urea N46%. �· Free floating, treated with anti caking treatment.
Free from Impurities, Sand, Dust and Certified Non Radioactive.
Physical state solid >20 and 101KPS, white granules.
Vapor density not applicable.
Floatability / Water sinks and mixes.
Molecular weight 60.065. PH Value 8.0 8.5.
USAGE
More than 90% of world industrial production of Urea is destined for use as nitrogen release fertilizer. Urea has the highest nitrogen content of all solid nitrogen content of all solid nitrogenous fertilizers in common use. Therefore, it has the lowest transportation costs per units of nitrogen nutrient. The standard crop nutrient rating of urea is 46 0-0.
The most common impurity of synthetic urea is Biuret, which impairs plant growth.
Urea is usually spread at rates of between 40 and 300 Kg./HA but rates vary. Smaller applications incur lower losses due to leaching. During summer season, Urea is often spread just before or during rain to minimize losses from volatilization (A process wherein nitrogen is lost to the atmosphere as Ammonia Gas). Because of the high Nitrogen concentration in Urea, it is very important to achieve an even spread. The application equipment must be correctly calibrated and properly used.
Our Petroleum Coke (non-calcined) is produced by refineries from Kazakhstan, Azerbaijan, Poland and the Middle East. Available for sale CIF to any safe world port from proven, reliable sellers. Alternative TTO, TTV, and STS deliveries. Buyer-friendly procedures. Buyer mandates welcome
Product FMEL002 Product FMEL99
3-ply face mask comfortable for user. The face mask is latex free and use brand new hypoallergenic material, odourless and lint-free.
Product Disposable 3-Ply Non-Woven Face Mask with Ear Loop Premium Medical Grade 3-Ply Face Mask with Ear Loop
Approx. Size 165 cm x 10 cm (each layer with 25gsm)
Colour Blue/Green/White/Yellow/Pink or can be customized
Outer Layer PP Spun bond Nonwoven: 25 gsm
Middle Layer PP Spun bond Nonwoven: 25 gsm
Inner Layer PP Spun bond Nonwoven: 25 gsm Outer Layer PP Spun bond Nonwoven: 25 gsm
Middle Layer PP Melt blown Filter (BFE >99%) : 25 gsm
Inner Layer PP Spun bond Nonwoven: 25 gsm
Nose Piece Polyethylene Aluminium
Packaging 50 pcs per box (plastic pack included) or 50 pcs per pack (no inner box); 40 boxes or packs per carton.
Capacity: 10,000 pcs/day
MOQ 100,000 pcs min. order
Packaging: 50 pieces per box/bag; 40 boxes per carton.
Payment condition: TT
Lead Time: 1 week
Shipping Duration: 7 Days (ONE WEEK)
Origin: MALAYSIA
Other Information: Manufactured by QMS Medical Device ISO 13485:2016 Certified Company
We are recognized as a reliable Manufacturer, Exporter and Supplier of Non Woven Fabric. We can provide Non Woven Fabric in any gram/sq. mtr and any color required by customer. Non Woven Fabrics are broadly defined as sheet or web structures bonded together by entangling fiber or filaments (and by perforating films) mechanically, thermally or chemically. PP Spun bonded Non woven Fabrics are produced using a precise extrusion-based technology. The polymer is stretched into a continuous filament and loosely spread onto a conveyor belt to form the web. Air is used to form and lay the fabric filaments. On the other hand, some non woven fabrics can be recycled after use, given the proper treatment and facilities. For this reason, Non woven fabrics is consider as a more ecological fabric for certain applications, especially in fields and industries where disposable products are important, such as hospitals, schools, nursing homes, hotels and luxury accommodations.
Non woven fabrics have various Properties such as Stretch ability, Flame retardancy, Wash ability, Strength, Absorbency, Liquid repellency, Resilience, Softness, Cushioning, Filtering, Bacterial barrier and Sterility. These characteristics are frequently combined to make fabrics suitable for exact jobs.
Woven bags for sugar,rice,fertilizer etc.
Non Lamination circular bags & fabric color and white
1. 22" (10x9) 850D
2. 22.5" (10x9) 850D
3. 26" (10x10) 900D
4. 26" (11x10) 900D
Inside Lamination (23-25mu) color and white
1. 17" (10x9) 900D Rolls
2. 20" (10x10) 900D Rolls
3. 22" (10x9) 900D Rolls
4. 17" (11x11) 900D Rolls (25mu)
