BRIGHTOMNI BBU-L is a Tetrasulpho type optical whitener used in Paper size press, coating and wet end applications,to achieve high whiteness and brightness properties of Paper.
BRIGHTOMNI BBU-L Liquid is special Optical Brightener of medium affinity Tetra Sulpho OBA for paper. It is an innovative OBA for the WET END application in acidic to neutral media (pH 4-7).
BBU-L has a broad spectrum of application and has good compatibility with Acids & Alum.
Average dosage 0.2 to 6.0 g/L with size press liquor.
BRIGHTOMNI BBU-L can perform with conventional Starch at the size press. Also together with CMC, PVA and anionic and slightly synthetic sizing additives. It can be a ready use optical whitener in size press. This product is used to attain moderate to high whiteness.
Falcon Dlx. 250 mm ( 9 & 10) Borewell Submersible Pumpsets are powered by water filled, rewindable submersibleMotor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressureand rigidly locked in stainless steel stator shell. T-Bolt design in all motor ensures rigid construction.
Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow MRS series 27Mtr head per stage in radial flow series.
- FG 250 Cast Iron Bowl with CED Catted and SS-304 Grade Impeller in Mix flow FMC Series 22Mtr head per stage in
Mix flow series.
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads.
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set.
- Dynamically balanced rotating parts ensures minimum vibration and longer life.
- Designed for wide voltage fluctuations.
- Motor portion covered with corrosive resistance Stainless steel (SS 304) shell.
- More durability and hygiene & High operating efficiency.
- Specially designed thrust bearing to withstand high axial thrust load.
- Extremely hardwearing water lubricated bearing.
- Thread type motor construction ensures service feasibility.
- Designed for wide voltage operation.
- Best alternative for JET & Compressor pump set.
- Additional intermediate bearing in higher stage pumps.
Specification
- Power Range : 55 kW to 112 kW (75 HP to 150HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Speed : 2900 RPM
- Head Range : 12 mtr. To 300 mtr.
- Discharge Range : 3600 LPM to 960 LPM
- Outlet Size in Inch : 4.0" & 5.0"
- Degree of Protection : IP 58
- Maximum Starts Per Hour : 10 Times
Falcon Premium 200 mm (8) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure and rigidly locked in stainless steel stator shell.
Salient Features
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- SS-304 Grade investment casting bowl and SS-304 grade impeller in radial flow series
- 20 Mtr. Head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting pad with carbon plate) to with stand axial thrust
loads
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Special designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures services feasibility
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS Pumps are available
Specification
Direction of Rotation : Counter clockwise from driving end -1ph : Electrically Reversible -3ph
- Power Range : 7.5 kW to 75 kW (10 HP to 100 HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Thrust Load : 7.5 kW -30 kW -10000 lbs
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 440 Mtr.
- Discharge Range : 2400 LPM to 300 LPM
- Outlet Size in Inch : 4.0" & 5.0"
- Degree of Protection : IP 58
- Minimum Cooling Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : Star Delta (SD)
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Falcon Premium 175 mm (7) Borewell Submersible pumpsets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure and rigidly locked in stainless steel stator shell.
Salient Features
- Cast iron casting bowl and SS-410 grade impeller in mix flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial
thrust loads.
- Specially designed Deep Drawn type pump ensures perfect alignment and Thereby increases the life of the pump set
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Special designed thrust bearing to withstand high axial thrust load
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures services feasibility
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
Specification
- Method of Starting : 3 ph -Direct Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 37.3 kW
- Power Range : 11.2 kW to 37.3 kW (15 HP to 50 HP)
- Version : Three Phase 350 to 415V, 50Hz AC Supply
- Speed : 2880 RPM
- Head Range : 18 Mtr. To 650 Mtr.
- Discharge Range : 1860 LPM to 55 LPM
- Outlet Size in Inch : 2.0 , 2.5 , 3.0 & 4.0
- Degree of Protection : IP 58
- Direction of Rotation : Electrically Reversible -3ph
- Thrust Load : 11.2 kW -37.3 kW -8000 lbs
- Minimum Cooling Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
137 Synthetic Carpet Suppliers
Short on time? Let Synthetic Carpet sellers contact you.
V6 Borewell Submersible Pumpset
Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under pressure.
Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series
- 60 feet head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial
thrust loads.
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Additional intermediate bearing in higher stage pumps
- Fully SS pump set are available in SS - 304 Grade
Specification
- Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V,
50Hz AC Supply.
- Speed : 2900 RPM
- Head Range : 12 Mtr. To 600 Mtr.
- Discharge Range : 1080 LPM to 170 LPM
- Outlet Size in Inch : 2.0, 2.5 , & 3.0
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct
Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.)
6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Falcon Premium 150 mm (6) Borewell Submersible Pumpsets are powered by water filled, rewindable submersible Motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated Copper winding wires and made up of low watt loss silicon steel laminations assembled under
pressure.
Salient Features
- SS 304 Grade Investment Casting Bowl and SS-304 Grade Impeller in radial flow series
- 60 feet head per stage in radial flow series
- Specially designed high performance thrust bearing (SS-420 Tilting Pad with Carbon plate) to with stand axial thrust loads.
- Dynamically balanced rotating parts ensures minimum vibration and longer life
- Motor portion covered with corrosive resistance Stainless steel J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Additional intermediate bearing in higher stage pumps
- Fully SS pump set are available in SS - 304 Grade
Specification
- Power Range : 2.2 kW to 30 kW (3.0 HP to 40 HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V,
50Hz AC Supply.
- Speed : 2900 RPM
- Head Range : 12 Mtr. To 600 Mtr.
- Discharge Range : 1080 LPM to 170 LPM
- Outlet Size in Inch : 2.0, 2.5 , & 3.0
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW 4.5 kW - 3500 lbs, 5.5 kW - 30 kW - 6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) upto 2.2kW: 3ph -Direct
Online (D.O.L) upto 5.5 kW, Star Delta (SD) upto 30 kW
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
V5 Borewell Submersible Pumpset
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are
assembled under pressure and rigidly locked in stainless steel stators shell.
Salient Features
- SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series)
- 9 Mtr. Head Per Stage In Radial Flow Series.
- Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial thrust loads.
- Dynamically balanced roating parts ensure minimum vibration and longer life
- Motor Portion covered with corrosion resistant S.S. J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS pumps are available in (GRS - Series)
Specification
- Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply
(Single Phase available in 3 HP to 5 HP)
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 640 Mtr.
- Discharge Range : 690 LPM to 80 LPM
- Outlet Size in Inch : 1.5 , 2.0" & 2.5"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW, 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2
kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star
Delta (SD) upto 9.3 kW
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m/sec (max.)
- Ph Value : 6.5 to 8.5
Falcon Premium 125 mm (5) Borewell Submersible pump sets are powered by water filled, rewindable submersible motor suitable for continuous duty. The stator is wound with special water proof synthetic film insulated copper winding wires. And, it is made up of low watt loss silicon steel laminations which are assembled under pressure and rigidly locked in stainless steel stators shell
Salient Features
- SS 304 Grade Investment Casting Bowl and Impeller in Radial Flow Series.(GRS - Series)
- 9 Mtr. Head Per Stage In Radial Flow Series.
- Specially designed high performance thrust bearing (SS-420 tilting pad with carbon plate) to withstand axial
thrust loads.
- Dynamically balanced roating parts ensure minimum vibration and longer life
- Motor Portion covered with corrosion resistant S.S. J4 shell
- More durability and hygiene
- High operating efficiency
- Extremely hardwearing water lubricated bearing
- Thread type motor construction ensures service feasibility
- Specially designed Deep Drawn type pump ensures perfect
alignment and Thereby increases the life of the pumpset
- Designed for wide voltage operation
- Best alternative for JET & Compressor pump set
- Additional intermediate bearing in higher stage pumps
- Fully SS pumps are available in (GRS - Series)
Specification -
- Power Range : 2.2 kW to 9.3 kW (3 HP to 12.5HP)
- Version : Single Phase 180V to 230V, Three Phase 350 to 415V, 50Hz AC Supply
(Single Phase available in 3 HP to 5 HP)
- Speed : 2880 RPM
- Head Range : 12 Mtr. To 640 Mtr.
- Discharge Range : 690 LPM to 80 LPM
- Outlet Size in Inch : 1.5, 2.0" & 2.5"
- Degree of Protection : IP 58
- Direction of Rotation : Counter clockwise from driving end -1 pH Electrically Reversible -3ph
- Thrust Load : 2.2 kW â?? 4.5 kW- 3500 lbs, 5.5 kW to 9.3 kW -6000 lbs
- Flow Along the Motor : 0.15 m/sec.
- Type of Duty : S1 (Continuous)
- Method of Starting : 1ph-Capacitor Start Capacitor Run (CSCR) up to 2.2
kW, 3ph - Direct Online (D.O.L.) upto 5.5 kW, Star
Delta (SD) upto 9.3 kW
- Maximum Starts Per Hour : 20 Times
Characteristics Of Clear Cold Water
- Maximum liquid temperature : 33C max
- Permissible amount of sand : 25 g/m
- Allowable solids : 3000 ppm (max.)
- Chloride ion density : 500 ppm (max.)
- Turbidity : 50 ppm silica scale (max.)
- Hardness (Drinking Water) : 300 ppm (max.)
- Specific gravity : 1.004 (max.) 6
- Viscosity : 6 1.75 x 10 m²/sec (max.)
- Ph Value : 6.5 to 8.5
Product Description
We are a reputed entity in the industry, actively engaged in offering an optimum quality range of Submersible Winding Wire.
Available in single multi stand from 0.5 mm to 4.0 mm and above
Details:
Water Resistant: Designed for underwater application for submersible pump motor
Tear Resistant: propagation of tear is difficult as the insulation is oriented bi-axially
DI Electric Strength: The multiple layer construction of submersible winding wire ensures high dielectric quality of insulation and places the insulations concentrically around the conductor
Higher Mechanical Strength: Submersible winding wire insulation is remarkably resistant to cut through and scrap abrasion. Thin cross sections ensures greater cut through stress and prevents general abuse
Least Current Leakage: Submersible winding wires have constant and many times higher insulation resistance even at the boiling point of water and the current leakage is minimal
Easy Winding: Since the overall diameter of Submersible winding wires is less than the conventional PVC winding wire, the winding resistance is less and the submersible pump motor is easy to wind
High Tensile Strength: In submersible winding wires, the insulation adds significantly to the tensile strength as it supports the wire at each point wherever excessive stretching occurs
Longer Life: The insulating material in Submersible winding wires is produced by biaxially oriented synthetic film and has a very long life.
