This kind of pumps has the specialties as follows: 1)If there isn’t vapor to generate, You can turn off the adulterating-gas valve to increase the vacuum degree. 2) The improvement of the adulterating-gas valve can make the pump have adequate adulterating gas amount as pumping vapor, so the cogulable gas can be eliminated timely and the pump oil can be prevented from being lactic. 3) It is installed with the device that can make oil revival in which the oil,water and vapor can be frozen and separated, so the oil can be cleaned in time, and be used repeatedly,therefore, the working time of the pump is prolonged and the working reliability is increased.
This series of vacuum pumps can be used by themselves or as the backing pumps of the Roots pumps,diffusion pumps,molecule pumps and titanium pumps.With the adulterating-gas valve,the pumps can suck a little coagulable gas,humid air or the mixture of gas and vapor,but which can not contain particle-shaped solid matter.
W series of pumps adopt the circle-shaped stationary valve and its ultimate pressure (absolute pressure) is lower than 2600Pa,while the WY series of pumps adopt stripe-shaped moving valves,and it’s ultimate pressure is lower than 1300Pa? This series of pumps are principally used in the trade of chemical industry,medicine-manufacturing,light industry, architecture material and wiring etc..We also serve the no-oil pumps according to the demand of user.
WL series of standing reciprocating vacuum pumps are the renewed products based on the primeval W series of lying ones.Compared with the W series of ones, they have the specialty as follows: 1) The gas valves are installed on the cover and neck of the cylinder(the W series ones are on the body of the cylinders),so it can increase the area of cooling water.The process of compressing gas is approximately isothermal,so it can decrease the loss of power and can save energy by 10%~15%.The area it holds can decrease by 1/2. 2) The piston of the lying reciprocating vacuum pump will go down because of the weight of itself ,so it will be worn away unsymmetrically. The WL series of ones improved this shortcoming,it can decrease the wearing away of the moving units as piston and connecting pole; 3) We can serve the no-oil WL series of standing reciprocating pumps.
JZJ2S type Roots-water ring vacuum system consists of the major pump i.e. ZJ type Roots vacuum pump and the backing pump i.e. two stage water ring vacuum pump. It can pump not only the common gas but also the gas that contains vapor and a little dust. Compared with the common mechanical vacuum pump and water ring vacuum pump, it has some advantages as follows: it can endure the oil,vapor and tiny dust,its ultimate vacuum is high and its pumping speed in higher vacuum is great,so it is a kind of ideal vacuum-obtaining equipment for drying,dehydrating and gas-expelling in the trade of light-spinning,grocery and chemical industry etc..
2SAT (double stage), 2STC double stage), SKC (single stage) series cone type liquid ring vacuum pumps adopt the international advanced manufacture technology. The cone type allotter structure make the area of suction and discharge port end, flow resistance minish, the speed of pumping enhance, the energy conservation effect is obvious.The base exhaust structure reduces the bearing stress, the service life is long, safe and reliable. This kind of product especially qualify processes of the high dust gas, including the soft fiber unclean gas, with partial liquids the gas, the high temperature gas, virulent or caustic gas and so on , widely applied in electric power, papermaking, petrochemical, coal etc industries.
2sk Series Of Two Stage Water Ring Vacuum Pumps Whose Suction Speed Is Great Even In Higher Vacuum, Are More Fit To Work When The Suction Pressure Is Between -0.085mp A And -0.095mp A.
Application SK series water ring vacuum pump and compressor are used for sucking and compressing air or other noncorrosive, nonsoluble gases which don’t contain solid grains to obtain certain vacuum and pressure in sealed vessele. The gas sucked in may be allowed to contain small amount of liquid. The vacuum pumps are used widely in mechanical, petrochemical, pharmaceutical, food and confectionary industries as well as in electron field. AS the gas is compressed isothermally in the process.so that it cannot be likely to result in any danger upon compressing or extracting flammable and explosive gas,thus making it more widely used. Features •It is designed with compact structure , thus make the maintenance more convenient; •It is widely used in compressing or extracting flammable, explosive gases which is allowed to contain vapor and small amount of liquid; •Using water as main working liquid, thus it can optimize the cost of maintenance; •It can be used under more rigid working condition.
Application and advantages: SKA(2BE) series liquid ring vacuum pumps and compressors are manufactured by our company integrating with advanced technology of the imported pumps from abroad. It has high efficiency and economic power consumption. These series products is single stage and single action structure, it has many advantages, such as compact structure, convenient maintenance, reliable running, high efficiency and economical powers consumption. The main advantages of SKA(2BE)series products: • All the bearings are the imported brand like NSK to ensure the precise orientation and the high stability during the working of the pump. • The material of the impeller is QT400 nodular iron or stainless steel to ensure the stability when the pump works under the rigorous condition and can extend the lifetime of the pump. • The casing is made of steel or stainless steel plates to extend the lifetime. • The shaft sleeve is made of stainless steel to improve the lifetime of the pump 5 times than the normal material. • The V-belt pulley (when the pump is driven by belt) is used the high precise pulley with taper bushing to keep the reliability of the pump and extend its life. And it is also easy for assembling and disassembling. • The coupling is used to drive the pump directly. The flexible part connecting the two half coupling is made of polyurethane that makes the pump more reliable. • The unique design to set the separator above the pump saves the space and decreases the noise efficiently. • All the parts are cast by the resin sands that make the pump surface very smooth. It is not necessary to cover the surface of the pumps with putty and gives out the heat efficiently.
Features • Space-saving installation Compared to conventional pumps, the 2BVseries of pumps design delivers the benefits of a simple, and motor are integral and self supporting, there is no need for additional base plates, couplings or guards, which add to the cost, complexity and overall size of the installation. • Rugged and reliable The main features of 2BV series vacuum pumps focused on durability and dependability. With a reinforced stainless steel shaft and sealed bearings, the 2BV series can provide up to 20000 hours of maintenance-free operation. • Quiet operation The 2BV is expertly designed and manufactured to be quiet and vibration free. With sound pressure levels of less that 75dBA, it complies with the strictest noise standards, eliminating the need for additional sound attenuating devices. • Advantages a. Compact structure. b. Rugged design of reliable operation and long service life. c. Precision-balanced rotor. d. For worldwide use with 50/60Hz motors. e. Available from stock. f. Low installation costs. g. Easy to service. h. Standard mechanical seal. i. Reinforced stainless-steel shaft Technology specification list:
, Characteristics of the equipment: The TC type of vacuum unit series, it made of anti-corrosion PP tank, buffer tank, RPP water pump, check valve, the structure compact, low energy consumption, high vacuum level, and removable. , Using Attention: 1, The equipment should be installed on the flat and solid foundation, to ensure the equipments' service intensity. 2, The tank should be filled with water before starting up ,and need to open water pump inlet valve. The water pump prohibits to idling in dehydration and inversion so that to prevent the water resource to damage. 3. When using circulating water tank should be offent to added the cooling water and replace the circulating water, to lower the working temperature, to protect the circulating water have the particles sundry. 4, When equipments downtime, it should be shut off the steam valve, and stop the roots vacuum pump, open the emptying valve of vacuum tank ,to reduce the degree of vacuum. Then stop working. Otherwise to make it to suck-back and to damage equipment.
MD Multistage Pump Size (discharge): 1 inch to 32 inch Capacity: 3.4~ 15000 m3/hr Head: 8.6~140m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc. MD Multistage Pump Introduction: Multistage Pump is single-suction,multistage,centrifugal pump,It is widely used for water supply&drainage infields of factories mines and cities.It is provided for delivering clear water without solid particles or other liquid which is physically and chemically similar to clear water. The temperature of the liquid is 0¡ãC~80¡ãC. Permissible inlet pressure is 0.6MPa MD Multistage Pump Features: 1. Stator: The main parts are suction casing, stage casing, discharge casing and diffuser. They are screw up by poles, to become a working house. It is horizontal, the discharge direction is upward; The discharge and suction direction of them are both upwards, and the suction direction is horizontal usually, also they can be made upward according to user's requirement. 2. Rotor: It is consist of shaft, impellers, balance dic and shaft sleeve etc. Shaft supplied power to impellers; The axial force is balanced by balance disc; The sleeve mounted on shaft to protect shaft. 3. Bearing parts: It is consist of bearing body, bearing and bearing cover etc. The bearing of type 85-67, 155-67, 600-60 pump is sliding bearing, lubricated by diluted oil, the other pump bearing is rolling bearing, lubricated by grease. 4. Shaft seal: It is usually adopted soft packing seal, consist of sealing house on suction casing, packing, blocking water ring, the sealing hose have some pressure water, to cool, lubricate and seal pump. The pumps usually adopt mechanical seal. 5. Drive: The pump is driven directly by motor through elastic coupling, the rotation of pump is clockwise looking from motor to pump. MD Multistage Pump Parameter Selection Table: MD Multistage Pump Application: Water supply and discharge in high-rise buildings Fire water supply in constructions Water supply and discharge in factories and mines Long distance delivery Cyclic pressurization in production
MDG Boiler Feed Water Pump Size (discharge): 1 inch to 32 inch Capacity: 3.4~ 15000 m3/hr Head: 8.6~140m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc. MDG Boiler Feed Water Pump Introduction: MDG Boiler Feed Water Pump can deliver clear water without solid particles or other liquid which the physical and chemical feature is similar with clear water. The boiler hot water circulating pump is suitable for boiler feed water or feed water of high-pressure boiler. The temperature range of liquid is from -20 ¡ãC to -150 ¡ãC and the inlet pressure of pump is less than 0.6 Mpa. MDG Boiler Feed Water Pump Features: 1) Stator parts of the MDG boiler feed water pump : It mainly consists of suction stage, mid-stage, discharge stage and diffuser; they are strained through a lever and form a working chamber. the inlet and the outlet are vertival upword. 2) Rotor parts of the MDG boiler feed water pump : It mainly consists of shaft, impeller, balance kettle and shaft sleeve. Shaft transfers power to impeller and make the pump work. The axial force is balanced by balance disc (kettle) and there is rechargeable shaft sleeve in shaft to protect shaft. 3) Bearing parts of the MDG boiler feed water pump: It mainly consists of bearing body, shaft cover and sliding bearing. There are two single centripetal ball bearing in bearing body to prevent balance disc (kettle) from abrasion. The sliding bearing is lubricated by dilute oil, there is cooling chamber in bearing body and the bearing can be cooled with exterior water. 4) Shaft seal parts of the MDG boiler feed water pump : Shaft seal uses soft packing seal. It mainly consists od seal box, packing, packing ring and packing cover. The shaft is sealed, cooled and lubricated by exterior water from seal chamber. The mechanical seal can also be used as requirement and it need be cooled, lubricated and washed by exterior water. 5) Drive: Type MDG boiler feed water pump is directly driven by motor through flexible coupling. View from motor end, the rotating direction of pump is clockwise. MDG Boiler Feed Water Pump Parameter Selection Table: Model Speed(r/min) Flow Head(m) Power(KW) NPSH (m) m3/h L/S Shaftpower Motorpower MDG6-25×3 2950 3.75 1.04 76.5 2.37 5.5 2.0 6.3 1.75 75 2.86 2.0 7.5 2.08 73.5 3.19 2.5 MDG6-25×4 2950 3.75 1.04 102 3.16 7.5 2.0 6.3 1.75 100 3.81 2.0 7.5 2.08 98 4.26 2.5 MDG6-25×5 2950 3.75 1.04 127.5 3.95 7.5 2.0 6.3 1.75 125 4.77 2.0 7.5 2.08 122.5 5.32 2.5 MDG6-25×6 2950 3.75 1.04 153 4.73 11 2.0 6.3 1.75 150 5.72 2.0 7.5 2.08 147 6.39 2.5 MDG6-25×7 2950 3.75 1.04 178.5 5.52 11 2.0 6.3 1.75 175 6.67 2.0 7.5 2.08 171.5 7.45 2.5 MDG6-25×8 2950 3.75 1.04 204 6.31 15 2.0 6.3 1.75 200 7.63 2.0 7.5 2.08 196 8.58 2.5 MDG6-25×9 2950 3.75 1.04 229.5 7.10 15 2.0 6.3 1.75 225 8.52 2.0 7.5 2.08 220.5 9058 2.5 MDG6-25×10 2950 3.75 1.04 255 7.89 18.5 2.0 6.3 1.75 250 9.53 2.0 7.5 2.08 245 10.63 2.5 MDG6-25×11 2950 3.75 1.04 280.5 8.68 18.5 2.0 6.3 1.75 275 10.5 2.0 7.5 2.08 269.5 11.71 2.5 MDG6-25×12 2950 3.75 1.04 306 9.47 18.5 2.0 6.3 1.75 300 11.44 2.0 7.5 2.08 294 12.78 2.5 MDG Boiler Feed Water Pump Application: This series boiler feed water pump is used for transport no solid particles contained water or Chemical and Physics water Boiler feed water and boiler circulation water High-rise building booster Urban Fire booster Long distance water transportation Boiler heating and cooling water circulation booster
MSG Inline Centrifugal Pump Size (discharge): 25mm to 450mm Capacity: 3.4~ 1200 m3/hr Head: 6m ~ 135 m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc MSG Inline Centrifugal Pump Introduction: MSG Inline Centrifugal Pump is a high-efficient, energy-saving product successfully designed by means of adopting the property data of MS model inline centrifugal pump and the unique merits of vertical pump and strictly in accordance with ISO2858 world standard and the latest national standard JB/T53058-93 and an ideal product to replace MS horizontal pump, DL model pump and other ordinary pumps. MSG Inline Centrifugal Pump Features: 1.Vertical structure, inlet and outlet diameters are same and on one center line, So it can be installed in pipe line like valves, it has compact and goodly externality, small floor area and low building investment, it can be used outdoor by add a shied on it. 2.Impeller mounted directly on the long axis of the motor, pump and motor bearing arrangement is reasonable, pump operation can effectively balance the radial and axial loads, thus ensuring the smooth operation of the pump,small vibration and low noise. 3.Mechanical shaft seal, use of imported titanium alloy seal ring, medium and high temperature mechanical seal with carbide materials, anti-wearing no leakage. 4.Easy installation and maintenance, no need to open pipeline system, the rotation parts of the pump can be pulled out by removing the screws on the pump. 5.According to the needs of flow and head, the pump can be used in series or parallel operation mode. MSG Inline Centrifugal Pump Parameter Selection Table: Model Flow(m3/h) Head(m) Speed(r/min) Power(Kw) Voltage(V) MSG15-80 1.5 8 2900 0.18 380 MSG20-110 2.5 15 2900 0.37 380 MSG20-125 2.5 20 2900 0.75 380 MSG20-160 2.5 32 2900 0.75 380 MSG25-110 4 15 2900 0.55 380 MSG25-125 4 20 2900 0.75 380 MSG25-125A 3.5 16 2900 0.75 380 MSG25-160 4 32 2900 1.5 380 MSG25-160A 3.7 28 2900 1.1 380 MSG32-100 4.5 12.5 2900 0.75 380 MSG32-125 5 20 2900 0.75 380 MSG32-125A 4.5 16 2900 0.75 380 MSG32-160 5 32 2900 1.5 380 MSG32-160A 4.5 28 2900 1.1 380 MSG32-160(I) 6.3 32 2900 2.2 380 MSG32-200 5 50 2900 3 380 MSG32-200A 4.5 44 2900 2.2 380 MSG Inline Centrifugal Pump Application: ▶Marine sea water ▶Cleanout system. ▶Every series of food machining and medicine produce ▶Environment protect system. ▶Waste water treatment for papermaking, metallurgy, galvanization, smelting, dye. ▶Electroplate and Dyeing system. ▶Industrial and chemical sump treatment ▶Explosion proof motor for oil, alcohol and other explosive liquid
MX Self Priming Pump Size (discharge): 25mm to 450mm Capacity: 3.4~ 1200 m3/hr Suction lift: Max. 6.5m Head: 6m ~ 135 m Efficiency:Up to 92% Materials:Cast iron,SS 304,SS 316,Bronze etc MX Self Priming Pump Introduction: MX Self priming pump made by our company is developed after our digestion, assimilation and improvement of domestic and foreign relevant technical data, which is a energy-saving kind of pump production. The pump is a kind of self-suction centrifugal pump, which has the advantages of compact structure, convenient operation, steady running, easy maintenance, high efficiency, long life, strong self-suction ability and so on. It doesn't need a foot valve on the pipeline, and just need to ensure that there is quantificational inducting oil stored in the pump case before work, so as to simplify the pipeline system and improve the working condition. MX Self Priming Pump Features: 1. Beautiful shape and fine structure,reliable performance. 2. With strong capacity of self priming, no need to equip with flap valve. 3. Non-clog, and with powerful capacity of passing big solid.. 4. Convenient for maintenance. MX Self Priming Pump Parameter Selection Table: MX Self Priming Pump Application: It is used in environment protection,construction,fire protection,chemical industry,phamary,printing and dyestuff,brewage,elctric power,electroplate,papermaking,petrol,washing for industry and mine,cool for device,etc. It is suitable for clear water,sea water and chemical medium with acid and alkali and mushy slurry(viscosity100 centipois),consistency for solid can not exceed 30% of total medium. When it's mounted with an arm sprayer, it can jet the water into the air to disperse into little raindrops for spraying, so it is a good tool for farm, nursery, orchard and tea garden. It is the ideal supporting pump for transfer slurry to filter press, it could matching with filter press of different specs and models.
The product has own advantage not only carry is convenient,durable,labor-saving,but also have been acquired ZBY 89001-88 international standard. It's used to all kinds of charge,such as bike,motorbike,car tyre,buoy,air bed,ball series etc.
Hand press water pump Features: 1) bs-type hand-press pumps are suitable for delivering well water, river water, or any Kinds of non-corrosive water 2) this product has a good structure, stable property and long service life 3) rotary action 4) cast-iron construction 5) types: bsd, bsf
Submersible water pump for water wells, mining, industries 1.5 to 300 HP
Spare parts of pumps like rotors stator.
Household pump parts.
