Find Verified Glass Glass Products Suppliers, Manufacturers and Wholesalers

The main products of the company are: pipeline glass fiber cloth, non-alkali glass fiber cloth, non-alkali hydrophobic glass fiber cloth, 7628/2116/1080 electronic cloth, glass fiber belt, black glass fiber cloth, mesh cloth, high silicon oxygen fiber cloth, fire cloth, fire blanket, three anti cloth, T cloth, etc.

Our HighFlux Aruvi series hollow fiber Cartridges have the following salient features

Membrane Packing - About 50 square meter Membrane Area
Pre-filtration - Suitable Pre-filter for RO; Municipal Water & Industrial Wastewater
Low Pressure - Around 2 bar Pressure Operation
Higher Permeate - up to 1-3 cubic meter Permeate (vary depends on actual conditions)
Backshwash - Easy backwash process and cleaning

The product is a structural plate which uses high-strength E-Glass roving as reinforcing material, thermosetting resin as matrix and then cast and formed on a special metal mold. It provides properties such as: light in weight, high strength, corrosion resistance, fire resistance, solid and anti-skid,.

FRP pultruded grating has the most characteristics of molded grating, but it has its distinct advantages, it has very high fiberglass content in the loading direction, so it has very high load capability, it has more superiority when used at wide span, so that the basic support will be decreased and the project cost will be reduced accordingly.

Adopted filament winding technique, computer-controlled Lianzhong filament winding FRP corrosion-resistant tanks possesses the advantages of lightness, high strength and corrosion resistance and was mainly used as the container of acid, alkali, salt etc. raw material and the middle, final products in the chemical industry.

Pultrusion profile is a kind of compound materials which is formed by taking fiberglass as the reinforced material, and taking thermosetting resin as base, the fiberglass continuous roving enable the product to have the extremely high longitudinal strength, the fiberglass mat (continuous strand mat, knitted mat and so on) makes the product have the good transverse strength. The thermosetting resin base is usually the unsaturated polyester resin, the vinyl resin, or the epoxy resin and the phenolic resin, the resin base enable the product to have the good anti-corrosion property, the different resin enables the product to be suitable for various corrosion environment, to add the ultraviolet inhibitor and fire retardant may enable the product to have the outstanding anti-aging property and the different rank anti-flammable property.

Product Information:
Fiber glass cloth is a multi-directional reinforced fabric made of glass fiber yarn, with plain weave, twill weave, satin weave.
Fiberglass cloth is an engineering material, which has the excellent merit such as anti-burns, anti-corrosion, stable-size, heat-isolation, minimum elongated shrinkage, high intensity.
1. Suitable for reinforced unsaturated resin, vinyl resin, epoxy resin, phenolic resin
2. Widely used in hand lay-up, pultrusion, winding and vacuum infusion and other processes
3. This new material product has already covered many domains such as electric appliances, electronic, transportation, chemical engineering, architectural engineering, heat insulation, sound absorption, fire prevention and environmental protection, etc. Terminal products include: pultruded profiles, auto parts, yachts, pipes, plates, sports equipment, wind energy blades and other FRP products.

Product Specifications
EW25: 25�±1g/m2, 100-3200mm Width, Plain;
EW50: 50�±2g/m2, 100-3200mm Width, Plain;
EW80: 80�±3g/m2, 100-3200mm Width, Plain;
EW100: 100�±3g/m2, 100-3200mm Width, Plain;
EW135: 135�±4g/m2, 100-3200mm Width, Plain;
EW160: 160�±5g/m2, 100-3200mm Width, Plain;
EW200: 200�±6g/m2, 100-3200mm Width, Plain;
EW300: 300�±9g/m2, 100-3200mm Width, Plain;
EWT100: 100�±3g/m2, 100-3200mm Width, Twill;
EWT135: 135�±4g/m2, 100-3200mm Width, Twill;
EWT160: 160�±5g/m2, 100-3200mm Width, Twill;
EWT200: 200�±6g/m2, 100-3200mm Width, Twill;
EWT300: 300�±9g/m2, 100-3200mm Width, Twill;
EWS300: 300�±9g/m2, 100-3200mm Width, Satin;

Product Properties:
1.High intensity and quick wet out
2.Anti-corrosion and electric insulation

Packaging Information�¯�¼?
It is wound onto paper tube and then wrapped up with plastic film, which can be packed in a cardboard box or woven bag. The rolls are to be horizontally placed rolls can be loaded into container directly or on pallets for Fiberglass stitched mat.

The spec as follows:
Name:E- Fiber glass
micron:9-11micron
Length:30cm-70mm
Color:white
We also can supply it with your requirements.Please kindly give us your requirements.

Chopped Strand Mat
Fiberglass Chopped Strand Mats are non-woven fabrics consisting of randomly distributed chopped strands held together with a powder or emulsion binder.
Chopped Strand Mat is compatible with unsaturated polyester, vinyl ester, epoxy and phenolic resins. The products are most widely used in hand lay-up process and can also be used in filament winding, Compression molding and continuous laminating processes. The typical end-use applications include various panels, boats, FRP roof shoot, Autonitive parts, bathroom equipment and cooling towers.

Product Features

1.Uniform density ensures consistent fiberglass content and mechanical properties of the composites products.
2.Uniform powder distribution ensures good mat integrity, little loose fibers and small roll diameter.
3.Excellent flexibility ensures good moldability with no spring-back at sharp corners.
4.Fast and consistent wet-out speed resins and rapid air release reduce resin consumption, improving manufacturing costs, productivity and mechanical properties of the end products.
5.The composite products have high dry and wet tensile strength and good transparency.

General Data

Binding type : Powder or Emulsion;
Densily : 85-900g/m2;
Width : Max.3300mm, Tapes available.
Edge : 1 or 2 untrimmed edge available upon request.

Surfacing Tissue

Surfacing Tissue mainly used in the surface layers of FRP products. It features even Fiber distribution, soft feel, level and smooth fiber surface, less glue content, quick resin soak and good pattern fitness. It can improve the product surface property on corrosion resistance, compressive strength, seepage resistance, and longer service life. It is also suitable for spraying; pattern pressing and other FRP pattern technology.

Packaging

Product is manufacture in form of a roll wrap on a paper tube then after packed in a plastic bag and placed with in a cardboard carton. Rolls can be loaded in a container directly or on pallets.

Stroge

Should be stored in dry, cool, clean and rain-proof area. Recommended temperature range of storage is between 10~30 and relative humidity between 50%~75%.

3-D spacer fabric construction is a newly developed concept . The fabric surfaces are strongly connected to each other bv the vertical pile fibers which are interwoven with the skins . Therefore, lhe 3-D spacer fabric can provide good skin-core debonding resistance, excellent durability and superior integrity. In addition, the interstitial space of the construction can be filled up wilh foams to provide synergistic support with vertical piles. These products have broad application prospects in automobile, Iocomotive, aerospace, marine, windmills, building and other industries.

Product Characteristics
The 3-D spacer fabric consists of two bi-directional woven fabric surfaces, which are mechanically connected with vertical woven piles. And two S-shaped piles combine to form a pillar, 8-shaped in the warp direction and 1-shaped in the weft direction.
The 3-D spacer fabric can be made of glass fiber, carbon fiber or basalt fiber. Also their hybrid fabrics can be produced.
The range of the pillar height:3-50 mm, the range of the width:3000 mm.
The designs of structure parameters including the areal density, the height and distribution density of the pillars are flexible.
The 3-D spacer fabric composites can provide high skin-core debonding resistance and impact resistance and impact resistance, light weight. high stiffness, excellent thermal insulation, acoustic damping, and so on.

Carbon fiber modification on engine hood,empennage, surrounding surface, car handle, rotary plate, ect,. is the desire of car fans. Car fans are bothered by this problem any more after the carbon fiber vinyl come out as its price is lower and easy to operate

Model : K9291, K9292, K9293, K9296, K9297

Material
Size : 127cm × 50M
Fabric : 0.09mm
Glue : 30µ
paper : 140g.

FP-02
Description
Insulated 16mm Rod Pin with a metal point and metal cap, which allows it to be struck with a hammer. Each Insulated Road Pin is flash tested to 10,000V.

Insulated non conductive road pins help reduce the risk of electric shock from buried cables. Manufactured from 12mm fibreglass rod with forged point, allowing it to penetrate a variety of surfaces.

Sizes Available : 16mm x 600-1500mm.

FP-01
Description
Insulated 12mm Rod Pin with a metal point and metal cap, which allows it to be struck with a hammer. Each Insulated Road Pin is flash tested to 10,000V.

Insulated non conductive road pins help reduce the risk of electric shock from buried cables. Manufactured from 12mm fibreglass rod with forged point, allowing it to penetrate a variety of surfaces.

Sizes Available : 12mm x 600-1500mm.

Attachments Available : Metal & Plastic Point & Plastic Hook End & Metal Cap.

FRP-04
Description
Epoxy fiber glass tube is high quality material as making high voltage electric devices.

Inner diameter(mm):
24 30 33 36 38 42 46 48 50 52 54 55
56 58 60 63 66 74 75 76 78 80 82 100 105
115 130 140 144 180 1851 94 210 240 245 250 253
Other Inside diameter is available.

Outer diameter and length can be made by customers specific requirements.

Features
Non-Corrosive
2. Dimensionally Stable

3. Lower Life Cycle Cost

4. Flame Retardant

5. Easy to Fabricate and Install

6. Electrically Non-Conductive

7. Lightweight/High Strength

8. Resists Insect Damage

9. High Impact Strength

10. Low Water Absorption

11. Greater Flexural Strength Than Timber

12. Non-Leeching

Physical,mechanical and dielectric property should follow the table below:
Technical requirement
Normal Diameter Thickness Length Tolerance Allowed
inside diameter outside diameter Length
30~70 3~20 500 ±0.3 ±0.3 ±1
70~150 3~20 1000 ±0.5 ±0.5 ±2
150~550 10~100 2800 ±0.5 ±0.2 ±2
Physical and mechanical parameters Physical and mechanical parameters
Index Name Unit Index Index Name Unit Index
Density g/cm3> 1.80 Density g/cm3> 1.80
Water absorption % 0.15 Water absorption % 0.15
Intensity of curvature(circling direction) Mpa 400 Intensity of curvature(circling direction) Mpa 400
Intensity of compress Mpa 98 Intensity of compress Mpa 98
Voltage vitality on parallel layer at normal state for 5min Kv 25 Voltage vitality on parallel layer at normal state for 5min Kv 25
Voltage vitalityon vertical layer in the oil at 90C for 5min MV/m 12 Voltage vitalityon vertical layer in the oil at 90Cfor 5min MV/m 12


Enquire Now
Epoxy fiber glass tube is made by good quality glass fiber steeped into epoxy resin of thermo-stability, which is high quality material as making high voltage electric devices, such as breakers, thimbles, mutual inductors, zinc oxide arresters, etc.

FRP-02
Description
This product is widely used in composite suspension long rod insulator, composite post insulator, composite cross-arm insulator, composite drop switch insulator, disconnector, wind deflection of composite insulator, spacer composite insulator, composite insulator for electric railway overhead contact line and other composite insulator industry. The product quality we manufacture for our clients is said to meet IEC 61109 DL/T 810 GB/T 13096-1 GB/T 775.3 JB/T 5892-91 and other related technical requirements.

We specialise on fiber glass products, which include the fiber glass rods, fiber glass tubes, fiber glass sheet as well as various fiber glass profiles like the fiber glassI beam,fiber glass channel,fiberglass angle, etc. Pultrusion process is a kind of method to make continuous composite profiles, which use the twist-less roving on the creel with other continuous reinforced composites, polyester surface mat to proceed the resin impregnation, and then keep the forming mould at certain section, makes the continuous deepening after curing in the intramode. Thus,the pultrusion products come out by this automatic production process. The common products like round rods, round tubes, flat bars, square tubes, angles, U-bars, joist steels,T profiles and other kinds of special profiles.

Characteristic
1). Corrosion resistant, light weight

2). Extremely strong and durable

3). High strength

4). Fire retardant

5). Good insulation

6). Good flexibility, corrosion resistant

Specification
Specification Item
Density 2.1g/cm3
Water Absorption <0.05 %
Tensile Strenth 1200 Mpa
Bending Strenth 900 Mpa
Flexural Strength in thermal state 300 Mpa
Water Diffusion Test (12 KV)1min <1 mA
Dye penetration pass after 15mins

FRP-01
Description
Epoxy Resin Fiberglass rod is adopt glass fiber steeped into epoxy resin pultrusion under high temperatures, which as features light weight,stable mechanical performance,high insulation performance in the range of 10KV to 1000KV.

The tensile strength can up to 1360Mpa

High-temperature rod,Acid-proof rod. This product can be used as the core rod of composite insulator, the vaulting pole of the arresters and the insulant of other high mechanical and electrical appliances.

Insulating Solid Rod is made of ECR glass reinforced epoxy resin.We use continuous pultrusion process .The products comply to the BS standards. Insulator core rods also are also called fiber glass rod, FRP rod, GRP rod, fiber glass bar, Insulation rod, fiber glass stick and so on. It is widely used in the electrical industry, our fiber glass epoxy resin rod products be exported to European Countries like France, Romania, Hungary and United Kingdom, and other countries like Vietnam.

Characteristic
1). Corrosion resistant, lightweight

2). Extremely strong and durable

3). High strength

4). Fire retardant

5). Good insulation

6). Good flexibility, corrosion resisting

Specification
Dimeter of rounded rod: D16, D18, D20, D24, D26, D28, D30, D32, D34, D36, D40, D46, D50,D53, D55, D60, D68, D70, D80, D90, D96, D100, D110, D150 and so on

Length of Round rod: 200mm to 6000mm, itâ??s depend on customer's request.

Also, can open new mould according to customer's demand.

Specification Item
Density 2.1g/cm3
Water Absorption <0.05 %
Tensile Strength 1200 Mpa
Bending Strength 900 Mpa
Flexural Strength in thermal state 300 Mpa
Water Diffusion Test (12 KV)1min <1 mA
Dye penetration pass after 15mins

Application:Polymer insulator/ Arrester/ Cut-out fuse

Technique:Pultrusion

Dimensions: 10-110MM

Material:Epoxy resin and Fiber glass

Color: Any

Type: Common rod, High-temperature rod, Acid-proof rod, Insulation Rod

GRP Gel coated, translucent, high gloss and smooth finish. With mat in its composition. White color. From 1.00 mm to 3.50 mm thick and from 1.6 m to 3.05 m wide. Length up to 60 meters. Other colors available on demand. Can be produced with or without Woven roving. Prices per m², according to composition, thickness, color and finish.

GRP Gel coated, texturized, high gloss and smooth finish. With mat in its composition. White color. From 1.00 mm to 3.50 mm thick and from 1.6 m to 3.05 m wide. Length up to 60 meters. Other colors available on demand. Can be produced with or without Woven roving. Prices per m², according to composition, thickness, color and finish.

GRP Gel coated, high gloss and smooth finish. With mat and white. From 1.00 mm to 3.50 mm thick and from 1.6 m to 3.05 m wide. Length up to 60 meters. Other colors available on demand.

Can be produced with or without Woven roving.

Prices per m2, according to composition, thickness, color and finish.