MB1004 LV-ProxSonar-EZ0
High Performance Ultrasonic Rangefinder
MB1004 LV-ProxSonar-EZ0 Ultrasonic Rangefinder Product Description
These ultrasonic proximity sensors detect objects in a calibrated detection zone. The LV-ProxSonar-EZ sensors report when an object (such as a person) enters the detection zone. The target is released after leaving the LVâ??ProxSonarâ??EZ detection zone.
The LV-ProxSonar-EZ0 has a detection zone of ~7 feet and will allow for 6+ simultaneous sensors.
MB1004 LV-ProxSonar-EZ0 Ultrasonic Rangefinder Product Specifications
* Resolution of 1 inch
* ~2.5 second target acquire time
* ~1.5 second target release time
* Automatic multi-sensor operation
* People sensor
* Maximum reported range of 254 inches (645 cm)
* ~7 foot proximity detection zone (84 inches or 213 cm)
* Run up to 6+ sensors in the same environment
* Choice of 2 digital outputs: Logic Level (High/Low) and RS232 serial
* 42kHz Ultrasonic sensor measures distance to objects
* RoHS Compliant
* Read from sensor outputs: Serial and Pulse Width
* Virtually no sensor dead zone, objects closer than 6 inches range as 6 inches
* Operates from 2.5-5.5V
* Low 2.0mA average current requirement
* Small, light weight module
* Designed for easy integration into your project or product
* Longest detection zone
ToughSonic 14 Level & Distance Sensor
PC or Button Setup, Waterproof, Two Selectable Outputs
TSPC sensors and SenixVIEW software put the power of ultrasonics in your hands yet retain the simplicity of push-button TEACH setup. You can quickly adjust, optimize, save and clone your applications without calibration!
ToughSonic sensors contain a rugged transducer potted in a stainless steel housing for long life.
Outputs respond to measured distance and non-contact technology means nothing touches your materials.
TSPC-30S1 Series Ultrasonic Level & Distance Sensor Features
Distance Measurements
* Long range, short dead band
* Unaffected by optical factors like color and transparency
* PC or button "teachable" setup
* Narrow beam with adjustments to optimize performance
* Temperature compensated
Packaging & Performance
* Quick mounting
* Durable sealed housing for wet or dirty applications
* Short & overload protected I/O
* Multi-sensor synchronization
* Adjustable sensitivity
* Rear status indicators (3)
Free Functionality using adjustable interface features like switch hysteresis and time delays to build complete solutions such as pump or material flow controllers. Save cost by eliminating PLCs, delay circuits and time delay relays!
OXY-LC Oxygen Sensor Interface Board Description
The OXY-LC Oxygen Sensor Interface Electronics provides the necessary electronics to power and control SST range of zirconium dioxide (ZrO2) sensors.
The OXY-LC Oxygen Sensor offers various user configurable output variants RS485, PWM, 0-10Vdc and 4-20mA. The RS485 Modbus RTU Protocol offers various benefits over other output types but most importantly it allows complete control of the sensor operation and access to all available information including sensor diagnostics, barometric pressure and pressure sensor temperature.
The adaptive software filtering which enables it to provide a fast response coupled with a stable oxygen output. In addition to this, the OXY-LC Oxygen sensor interface electronics offers a high accuracy linear output for all of our zirconium dioxide oxygen sensors.
The built in pressure sensor allows for barometric pressure compensation and the interface mounted screw terminals offers easy wiring with reverse voltage and transient overvoltage.
OXY-LC Oxygen Sensor Interface Board FEATURES
* Provides the electronics necessary to power and control SST range of zirconium dioxide (ZrO2 ) sensors
* Built in pressure sensor for barometric pressure compensation
* Interface mounted screw terminals for easy wiring with reverse voltage and transient overvoltage
OXY-LC Oxygen Sensor Interface Board BENEFITS
* Adaptive software filtering provides a fast sensor response coupled with a stable oxygen output
* High accuracy linear outpu
Oxy-comm zirconia oxygen analyser description
The oxy-comm zirconia oxygen analyser is designed for controlled atmosphere applications such as refrigerated transportation containers and fire prevention.
The oxy-comm zirconia oxygen analyser combines a high accuracy zirconium dioxide oxygen sensor with a networkable, fault tolerant rs485 interface. The oxygen analyser is mounted under a stainless steel hood to protect it from the environment. The ip65 waterproof die-cast aluminium housing accommodates the electronics and has a 4-pole m12 connector to allow multiple devices to be interconnected.
The oxygen sensor inside oxy-comm uses a unique closed loop measurement system. While oxy-comm continuously measures the oxygen level, a heartbeat signal is also generated providing an immediate warning of any failures. Due to the innovative design, the oxy-comm zirconia oxygen analyser does not require a reference gas. Low drift means these products do not require frequent calibration but when they do, it is an extremely simple process which can be performed in fresh air which means there is no need for expensive calibration gases.
The oxy-comm zirconia oxygen analyser has an 8 to 15vdc supply voltage range with reverse polarity and transient overvoltage protection. The oxygen analyser is barometric pressure compensated and can be calibrated in fresh air (20.7% o2) or to any other known o2 concentration.
Oxy-comm-rs485 zirconia oxygen analyser features
* 8-15v dc supply voltage with reverse polarity and transient overvoltage protection
* networkable, fault tolerant rs485 interface, short circuit and overvoltage protection
* can be calibrated in fresh air (20.7% o2 ) or to any other known o2 concentration
* barometric pressure compensation
Oxy-comm-rs485 zirconia oxygen analyser applications
* refrigerated transportation containers
* protecting historical artefacts against oxidation
* fire prevention in facilities such as server rooms, or document storage
Our wind speed sensors have proven themselves in wind tunnel tests, in mountain-top tests and in thousands of household and institutional installations to be rugged, reliable and highly accurate.The type #41 generator has recorded wind to 214 mph.
Their low moment of inertia and unique bearings permit very rapid response to gusts and lulls. The black lexan cups (virtually shatter-proof) have thermal propertieswhich let it resist and shed icing far more effectively than metal assem-blies. Because of their output linearity these sensors are ideal for use with various data retrieval systems. The experience that maximum hasbuilt up over the years has provided the basis of our solid confidencein these sensors for a wide variety of applications.
Wind speed sensor 400 environmental
Operating temperature: -67 to + 130 degrees f
Operating humidity range: 10 to 100% rh
Wind speed sensor 400 technical specifications
* 3 cups of conical cross-section, 2" diameter. 7.5" swept diameter of rotor.
* 2 diameter housing.
* 3.2 overall assembly height.
* moment of inertia of rotor assembly = 68 x 10-6 x s-ftâ². Material of cups is black lexan.
* material of housing is black abs.
* shaft material is beryllium copper; fully hardened. Upper and lower bearings of modified teflon, self-lubricating.
* they have a rated pv factor of 20, 000 (at 15mph, pv is approx. 500; at 100mph pv is approx. 2, 000).
* upper bearing is centered in the plane of cup thrust for optimal loading.
* permanent magnet: indox 1, 1"dia. Long, 4 poles. Generators mount (using a cotter pin) on a 0.500" diameter mast with a #35 hole 0.350" from top of mast.
* starting threshold < = 4 mph distance constant 10 feet
162753 Electronics Communications Suppliers
Short on time? Let Electronics Communications sellers contact you.
The cv7 range of products features lateral transducers delivering four independent measurements. The validity checks are used to measure head wind vectors for calculations. This method gives a wind speed sensitivity of 0.15 m/s, and reliability and excellent linearity up to 40 m/s.
Cv7-v ultrasonic wind speed sensor specification:
Output data format: nmea0183; mwv, xdr
Information transmited: instant. W. Speed, instant. W. Angle, avaibility
Output rate: 2 hz / 30 hz measurement
Wind module sensitivity: 0.12 m/s
Wind module resolution: 0.05 m/s
Wind module dynamic: 0.12 to 40 m/s
Direction sensitivity: +/-1.5'
Direction resolution: 1'
Power supply: 8 v to 30 v dc
Electrical consumption: 9 ma
Op. Temp. Without icing: -15'c to +55'c
Cable: 25 m / 4x0.22 mm2
Connection: 4 wires
Weight of the head: 100 gr
Weight of unit assembly: 200 gr with mounting part
Mounting: vertical ; 300 aluminium arm, 16 mm
Rdo-200 fluorescence dissolved oxygen sensor application
Widely used in online dissolved oxygen monitoring for power plant, chemical, industrial wastewater, pharmaceutical, biochemical and water treatment industry.
Rdo-200 fluorescence dissolved oxygen sensor feature
* 0-20mg/l or 0-200% saturation
* 0 ~ 50'c; ip68 protection rating
* no film, no electrolyte, not polarization
* no consumption of oxygen, the flow rate is not affected
* built-in temperature sensor, automatic temperature compensation
* chemical interference from sulfide
* in drift, fast response, more accurate measurements
* maintenance-free longer applicable period, lower cost
* fluorescent cap replacement is simple
* supports rs-485, modbus protocol
Technical instructions
Do range: -20mg/l 0-20 mg/l or 0-200% saturation
Reaction time: 10 sec
Degree of protection: ip68
Do accuracy±1%
Sensor drift:
This product is one of the optical transmitter cyanobacteria and red algae, using ultraviolet light absorption principle, protection class ip68, can be installed directly into the formula, suitable for all occasions need to measure blue-green algae, such as marine environmental monitoring and other industries.
Technical parameters
Measurement range:
Blue algae: 0~100ug/l (bga-pc)
Red algae: 0~80ug/l(bga-pe)
Resolution: 0.01ug/l
Accuracy: ±1%f.S.
Working temperature: 0~40'c.
Working pressure:
Properties of the tocon-abc10 sic uv photodetector
* broadband sic based uv photodetector in to5 housing with attenuator
* 0 - 5 v voltage output
* peak wavelength at 290 nm
* max. Radiation (saturation limit) at peak is 18 w/cm2, minimum radiation (resolution limit) is 1.8 mw/cm2
* applications: uv hardening control and other very high uv radiation sources
Sic uv photodetector tocon-abc10 specifications
Spectral characteristics
Typical responsivity at peak wavelength: 0.28 mv/mw/cm2
Wavelength of max. Spectral responsivity: 290nm
Responsivity range: 227 360nm
General characteristics (t=25'c, vsupply=+5 v)
Supply voltage: 2.5 - 5v
Dark offset voltage: 50âµv
Temperature coefficient at peak: < -0.3%/k
Current consumption: 150âµa
Bandwidth (-3 db): 15hz
Risetime (10-90%): 0, 069s
(other risetimes on request)
Maximum ratings
Operating temperature: -25 +85'c
Storage temperature: -40 +100'c
Soldering temperature (3s): 300'c
Properties of the sg01d-a18 uv photodiode
* uva-only sensitivity, ptb reported high chip stability
* active area a = 0.50 mm2
* to18 hermetically sealed metal housing, 1 isolated pin and 1 case pin
* 10µw/cm2 peak radiation results a current of approx. 1.85 na
Spectral characteristic
Typical responsivity at peak wavelength: 0.037/aw
Wavelength of max. Spectral responsivity: 331nm
Responsivity range: 309 - 367nm
Active area: 0.50mm2
Dark current (1v reverse bias): 1.7fa
Capacitance: 125pf
Short circuit (10µw/cm2 at peak): 1.85na
Temperature coefficient: < 0.1%/k
Maximum rating
Operating temperature: -55 - +170'c
Storage temperature: -55 - +170'c
Soldering temperature (3s): 260'c
Reverse voltage: 20v
Gp2y0a41sk0f
Distance measuring sensor unit
Measuring distance : 4 to 30 cm
Analog output type
Sharp distance measuring sensor gp2y0a41sk0f description
Gp2y0a41sk0f is a distance measuring sensor unit, composed of an integrated combination of psd (position sensitive detector) , ir-led (infrared emitting diode) and signal processing circuit.
The variety of the reflectivity of the object, the environmental temperature and the operating duration are not influenced easily to the distance detection because of adopting the triangulation method.
This device outputs the voltage corresponding to the detection distance. So this sensor can also be used as a proximity sensor.
Sharp distance measuring sensor gp2y0a41sk0f features
1. Distance measuring sensor is united with psd, infrared led and signal processing circuit
2. Short measuring cycle (16.5ms)
3. Distance measuring range : 4 to 30 cm
4. Package size (29.5 x 13.0 x 13.5mm)
5. Analog output type
transform between hl/hrc/hrb/hb/hv/hs.
store the latest 250 groups measurements.
select measured material and way by key.
can show measurements repeatedly to remove the large errors.
use usb data output with connection pc.
provide bluetooth data output choice.
Product parameters
Accuracy
Display error 0.8% at ld=900
Measuring range:200~900 hld
Measurable material:9 different common materials
Operating temperature:-10°c~50°c°c
Relative humidity:90%
Size:140x70x30 mm
Power supply2x1.5vaaa um-4 battery
Weight:130 g (not including batteries)
The shore hardness tester as-120 series including type(a, b, c, d, e, o, do, oo), model complete, with different probe size, use for different measured objects and hardness value, to meet different request for kinds of material hardness measure. integrated design, small volume, light weight, simple structure, easy to use, intuitive readings and automatic shutdown function.
with low battery alarm indicator & average value calculation function.
auto switch off and manual shutdown.
use usb data output with connection pc.
provide bluetooth data output choice.
Accuracy1h
Resolution:0.1h
Range:1090h
Operating temperature:040°c
Size:170x63x24 mm
Power supply2x1.5vaaa um-4 battery
Weight:310 g (not including batteries)
Liquid level switches
Honeywell lle series alternatives
For part numbers lle101000, lle102000, lle103000 and lle105000
Liquid level sensor llc101000 features
* liquid level switches that can detect almost any liquid type; oil or water based
* choice of mounting; internal or external
* choice of threads
Sht20 digital temperature and humidity sensor product summary
The sht20 humidity and temperature sensor of sensirion has become an industry standard in terms of form factor and intelligence: embedded in a reflow solderable dual flat no leads (dfn) package of 3 x 3mm foot print and 1.1mm height it provides calibrated, linearized sensor signals in digital, i2c format.
The sht2x sensors contain a capacitive type humidity sensor, a band gap temperature sensor and specialized analog and digital integrated circuit - all on a single cmosens chip. This yields in an unmatched sensor performance in terms of accuracy and stability as well as minimal power consumption.
Every sensor is individually calibrated and tested. Lot identification is printed on the sensor and an electronic identification code is stored on the chip which can be read out by command. Furthermore, the resolution of sht2x can be changed by command (8/12bit up to 12/14bit for rh/t) and a checksum helps to improve communication reliability.
With this set of features and the proven reliability and long-term stability, the sht2x sensors offer an outstanding performance-to-price ratio. For testing sht2x two evaluation kits ek-h4 and ek-h5 are available.
Sht20 digital temperature and humidity sensor features
* fully calibrated
* digital output, i2c interface
* low power consumption
* excellent long term stability
* dfn type package reflow solderable
Sht20 digital temperature and humidity sensor performance
Size: 3 x 3 x 1.1 mm
Output: i²c digital, pwm, sdm
Supply voltage range: 2.1 to 3.6 v
Energy consumption: 3.2µw (at 8 bit, 1 measurement / s)
Rh operating range: 0 - 100% rh
T operating range: -40 to +125'c (-40 to +257'f)
Rh response time: 8 sec (tau 63%)
Sht21 digital humidity and temperature sensor product summary
The sht21 humidity and temperature sensor of sensirion has become an industry standard in terms of form factor and intelligence: embedded in a reflow solderable dual flat no leads (dfn) package of 3 x 3mm foot print and 1.1mm height it provides calibrated, linearized sensor signals in digital, i2c format.
The sht2x sensors contain a capacitive type humidity sensor, a band gap temperature sensor and specialized analog and digital integrated circuit all on a single cmosens chip. This yields in an unmatched sensor performance in terms of accuracy and stability as well as minimal power consumption.
Every sensor is individually calibrated and tested. Lot identification is printed on the sensor and an electronic identification code is stored on the chip - which can be read out by command. Furthermore, the resolution of sht2x can be changed by command (8/12bit up to 12/14bit for rh/t) and a checksum helps to improve communication reliability.
With this set of features and the proven reliability and long-term stability, the sht2x sensors offer an outstanding performance-to-price ratio. For testing sht2x two evaluation kits ek-h4 and ek-h5 are available.
Sht21 digital humidity and temperature sensor features
* fully calibrated
* digital output, i2c interface
* low power consumption
* excellent long term stability
* dfn type package - reflow solderable
Sht21 digital humidity and temperature sensor performance
Size: 3 x 3 x 1.1 mm
Output: iâ²c digital, pwm, sdm
Supply voltage range: 2.1 to 3.6 v
Energy consumption: 3.2âµw (at 8 bit, 1 measurement / s)
Rh operating range: 0 - 100% rh
T operating range: -40 to +125'c (-40 to +257'f)
Rh response time: 8 sec (tau 63%)
Reliable galvanic sensing technology
Compact 12mm design
For portable, laboratory or on-line use
Optional integral atc element
Easy to use pre-membraned replacement caps
The do1200 and do1200tc feature dependable galvanic technology. No warm up period is required. Sensors are supplied with fast responding hdpe membrane caps for portable or lab use. Optional ptfe membrane caps are available for on-line or heavy uv exposure applications. Fill solution is replaceable when required.
The do1200 is supplied without internal temperature compensation. The do1200tc can be supplied with a variety of user defined atc elements. Standard cable length is 2.5 feet with a tinned lead termination. Longer cable lengths and connectors are available for an additional charge. For on-line use, our fc75p 3/4 inch in-line fitting may be ordered to provide for mounting into 3/4 inch fnpt threaded tees.
Do1200 laboratory dissolved oxygen sensor specifications
Range: 0-20 mg/l
Body material: epoxy and noryl
Max temperature: 50 degrees c
Saturation output:
Hdpe = 47mv +/- 9mv,
Ptfe = 33mv+/-9mv
Pressure: 0-100 psig (7.5 bar)
Calibration: single point in air
Response time: after equilibration, hdpe 1 minute for 2mv, ptfe 2 minutes for 2mv
Large solution capacity for long term deployment
Models with and without temperature sensor
Easy installation and maintenance
Mv or 4-20ma output models available
The do6400 & 7400 series dissolved oxygen sensors feature a large capacity electrolyte holder, positive fit, easy to replace membrane and dependable galvanic cell technology for long term deployment. The body design ensures a good grip when wet. Ideal for aquaculture and wastewater monitoring applications, these sensors require minimal maintenance. Ptfe or high-density polyethylene (hdpe) membranes are available. 2 replacement membranes, installation tool and electrolyte are included. Additonal maintennace parts are in convenient kits (see ordering information). Sensors with mv output as well as built-in 4-20ma output in 0-100% and 0-200% saturation range are available.
Dissolved oxygen sensors specifications
O2 measuring range:
Do6400, do6400tc (0.5-20ppm), do6441(0-100%), do6442(0-200%)
Do7400, do7400tc (0.03-20ppm), do7441(0-100%), do7442(0-200%)
Body: material noryl
Cathode: silver
Anode: zinc (do6400 series), lead (do7400 series)
Maximum temperature: 50 degrees c
Power requirement: 12-36v dc (for models do6441, do6442, do7441 and do7442 only )
1. Uv sensor guva-c22sd features
Gallium nitride based material
Schottky-type photodiode
Photovoltaic mode operation
Good visible blindness
High responsivity & low dark current
1. Uv sensor guvb-t11gd-l features
Aluminium gallium nitride based material
Schottky-type photodiode
Photovoltaic mode operation
Good visible blindness
High responsivity & low dark current
