Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module description
Quickly integrate hydrogen sulfide sensing into your system with very low power consumption and a simple analog sensor signal output.
The ulpsm converts the hydrogen sulfide sensors linear current signal output to a linear voltage signal, while maintaining the sensor at its ideal biased operation settings.
Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module benefits
0 to 3 v analog signal output
Low power consumption < 45 uw
Fast response
On-board temperature sensor
Easy sensor replacement
Standard 8-pin connector
Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module applications
Fixed industrial safety monitoring
Portable industrial safety monitoring
Portable personal safety monitor
Indoor air quality monitoring
Outdoor air quality monitoring
Bad breath/halitosis sensing
Ulpsm-h2s 968-003 ultra-low power analog h2s sensor module performance characteristics
Measurement range: 0 to 50 ppm
Lower detection limit: 0.3 ppm
Resolution: 0.15 ppm
Accuracy: < â± 2 % of reading
Response time t90: < 30 seconds
Power-on stabilization time: 60 minutes recommended
4nd citicel nitrogen dioxide sensor key features & benefits
, industry leading reliability
, improved performance variability
4nd citicel nitrogen dioxide sensor application
Industrial safety: sensors for portable gas detectors used in industrial hygiene and confined space entry.
4nd citicel nitrogen dioxide sensor performance characteristics
, nominal range: 0-20 ppm
, expected operating life: two years in air
, output signal: 0.6 , ± 0.15 ua/ppm
, resolution: 0.1 ppm
, repeatability:
Sg01l-5lens
Concentrator lens sic based uv photodiode avirtual = 55 mm2
Properties of the sg01l-5lens uv photodiode
Broadband uva+uvb+uvc, ptb reported high chip stability, for flame detection
Radiation sensitive area a = 55 mm2
To5 hermetically sealed metal housing with concentrator lens, 1 isolated pin and 1 case pin
10âµw/cm2 peak radiation results a current of approx. 700 na
Sg01l-5lens uv photodiod specifications
Sensitive area: 55 mm2
Dark current: 3.5 fa
Capacitance: 250 pf
Responsivity range: 221 - 358 nm
Operating temperature: -55 ~ +170â°c
Storage temperature: -55 ~ +170â°c
Soldering temperature (3s): 260â°c
Reverse voltage: 20 v
Spd005gasmd 5 psi gauge pressure sensor with analogue output description
This pressure sensor has an amplified analogue output. The sensor is compensated for offset, sensitivity, temperature drift and nonlinearity.
The sensor is available in the range from 5 to 100 psi. Other ranges on request. Available in gauge and absolute type. The output is ratiometric to the power supply voltage. 5 v power voltage the output span is 0.5 to 4.5 v. The spd analogue series can be considered as an "analogue" successor of the spd series.
Sonic-anemo-dzp ultrasonic wind speed sensor description:
Sonic-anemo-dzp ultrasonic anemometer is powered by its own solar panel. It is well suited to remote installations where power consumption matters. This unit connects directly to a pulse or potentiometer input (i.E. On davis instruments). It is a useful product for professionals, integration to aws (autonomous weather station), and well-informed users.
Sonic-anemo-dzp ultrasonic wind speed sensor specification:
, output rate: 1 measure and update per second
, wind module sensitivity: 0.12 m/s
, wind module resolution: 0.05 m/s
, wind module dynamic: 0.12 to 40 m/s
, direction sensitivity: +/-1.5'
, direction resolution: 1' (9 bits)
, power supply: photovoltaic panel, battery lifepo4
, op. Temp. Without icing: -15'c to +55'c
Do1200 dissolved oxygen sensor features
* reliable galvanic sensing technology
* compact 12mm design
* for portable, laboratory or on-line use
* optional integral atc element
* easy to use pre-membraned replacement caps
Do1200 dissolved oxygen sensor description
The do1200 and do1200tc feature dependable galvanic technology. No warm up period is required. Sensors are supplied with fast responding hdpe membrane caps for portable or lab use. Optional ptfe membrane caps are available for on-line or heavy uv exposure applications. Fill solution is replaceable when required.
The do1200 is supplied without internal temperature compensation. The do1200tc can be supplied with a variety of user defined atc elements. Standard cable length is 2.5 feet with a tinned lead termination. Longer cable lengths and connectors are available for an additional charge. For on-line use, our fc75p 3/4 inch in-line fitting may be ordered to provide for mounting into 3/4 inch fnpt threaded tees.
Do1200 dissolved oxygen sensor specifications
* range: 0-20 mg/l
* body material: epoxy and noryl
* max temperature: 50 degrees c
* saturation output: hdpe = 47mv +/- 9mv, ptfe = 33mv+/-9mv
* pressure: 0-100 psig (7.5 bar)
* calibration: single point in air
* response time: after equilibration, hdpe 1 minute for 2mv, ptfe 2 minutes for 2mv
Mb7139 xl-trashsonar-wr
High performance ultrasonic trash bin measurement
Mb7139 xl-trashsonar-wr ultrasonic sensor product description
The mb7139 xl-trashsonar-wr1 is a weather resistant sensor designed for trash bin level measurement.
The mb7139 xl-trashsonar-wr1 reports the range to the first detectable target in a trash bin. This sensor is our most recommended sensor for testing within trash bins.
High output acoustic power combined with continuously variable gain, real-time background automatic calibration, real-time waveform signature analysis, and noise rejection algorithms results in virtually noise free distance readings. This holds true even in the presence of many of the various acoustic or electric noise sources. The xl-trashsonar-wr sensors are factory calibrated to match narrow sensor beam patterns and provide reliable mid-range detection zones.
Mb7137 is the i2c version of this sensor.
Mb7139 xl-trashsonar-wr ultrasonic sensor product specifiations
Resolution of 1 cm
10hz read rate
42khz ultrasonic sensor measures distance to objects
Rohs compliant
Read from all 3 sensor outpus: analog voltage, pulse width, rs232 serial
Operates from 3.0-5.5v
Operational temperature from -40'c to +65'c
Maximum range of 350 cm (138 inches)
Mb7139 xl-trashsonar-wr ultrasonic sensor features and benefits
Real-time calibration, noise rejection and additional filtering provides stable range information
Excellent for applications that require consistently accurate outputs
Impressive acoustic and electrical noise resistance
Mb7139 xl-trashsonar-wr ultrasonic sensor applications and uses
Autonomous navigation
Environments with acoustic and electrical noise
Bin level measurement
Tank level measurement
Trash level measurement
SONIC-ANEMO-DVC Ultrasonic Wind Speed Sensor Description:
As Worldwide Premiere launch, a specific version of the CV7-V which connects directly to the wind sensor input on Davis instruments.
This sensor will allow the replacement of mechanical anemometers / wind vanes with no need of anything else but power supply.
Itâ??s an exclusive and useful product for both, professionals and well-informed amateurs.
SONIC-ANEMO-DVC Ultrasonic Wind Speed Sensor Specification:
* Output rat: 2 Hz / 30 Hz measurement
* Wind module sensitivity: 0.12 m/s
* Wind module resolution: 0.05 m/s (16 bits)
* Wind module dynamic: 0.12 to 40 m/s
* Direction sensitivity: +/-1.5'
* Direction resolution: 1' (9 bits)
* Power supply: 2.7 V to 35 V DC
* Electrical consumption: 2.6 mA Avg. @ 12 V
* Op. temp. without icing: -15'C to +55'C
Y504-A Dissolved Oxygen Sensor Description
The sensor is based on optical fluorescence lifetime quenching technique. Its technical procedure meets ASTM D888-09 standard for optical sensing of dissolved oxygen. This online sensor is developed to integrate with Yosemite wireless monitoring system. Its rugged design and large measurement range make it ideal for sampling, flow cell, ground water and waste water measurements.
Y504-A Dissolved Oxygen Sensor Applications
Fish farmer, waste water plant, river, stream, and ocean monitoring
Y504-A Dissolved Oxygen Sensor Feature
* 0-20mg/L or 0-200% Saturation
* 0~50 'C; IP68 rating
* Membraneless, no electrodes design
* No oxygen consumption
* Flow Independent
* Automatic temperature compensation
* No H2S Interference
* Low Drift, fast response, and more accurate
* Low Maintenance, low operating cost
* Easy sensor cap replacement
* RS-485; MODBUS protocol compatible
SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Description
SONIC-ANEMO-SDI is made from the CV7-V to which a SDI12 protocol and optimizing electrical consumption has been added. Sample rate is 2 Hz.
This ultrasonic wind sensor operates in a request-response mode.
This product is more energy-efficient than standard units.
The SONIC-ANEMO-SDI is dedicated to meteorological applications.
SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Available data:
- Average speed and direction over 10 minutes
- Minimum wind speed and direction for that period
- Maximum wind speed (gust 3s) and direction for that period
- Software version and serial number
- Data measurement quality rate from the sensor
- Data for sensor diagnostic (manufacturer use only)
SONIC-ANEMO-SDI Ultrasonic Wind Speed Sensor Specification:
* Output rate: 2 Hz / 30 Hz measurement
* Wind module sensitivity: 0.12 m/s
* Wind module resolution: 0.05 m/s
* Wind module dynamic: 0.12 to 40 m/s
* Direction sensitivity: +/-1.5'
* Direction resolution: 1'
* Power supply: 2.7 V to 35 V DC
* Electrical consumption: 2.9 mA Avg. @ 12 V
* Op. temp. without icing: -15'C to +55'C
CV7-OEM Ultrasonic Wind Speed Sensor Description
CV7-OEM shows the same features as the CV7 standard: light, compact and low energy consumption.
With this OEM version of the Static Wind Transducer CV7, you can add an accurate Ultrasonic Wind Sensor to your own products and installations. It is powered by 8-30 VDC power supply and it outputs RS232/RS422/NMEA0183 signal.
CV7-OEM Ultrasonic Wind Speed Sensor Specification:
* Output rate: 2 Hz / 30 Hz measurement or *4 Hz / 60 Hz meas.
* Wind module sensitivity: 0.12 m/s
* Wind module resolution: 0.05 m/s
* Wind module dynamic: 0.12 to 40 m/s
* Direction sensitivity: +/-1.5 degree
* Direction resolution: 1 degree
* Power supply: 8 V to 30 V DC
* Electrical consumption: 9 mA
* Op. temp. without icing: -15 degree C to +55 degree C
CV7-E Ultrasonic Wind Speed Sensor Description
The CV7-E is easily integrated into measurement and monitoring systems. Detects gusts with great responsiveness and low latency. The CV7-E is powered by 8-30 VDC power supply and it outputs RS232 / RS422 / 5 V level signal / NMEA0183.
The CV7-E shows a data rate twice faster than the CV7 and CV7-V with a data output 4 per second.
The small size of this sensor makes it very discreet.
Like every LCJ Capteurs products, CV7-E is energy efficient.
CV7-E has proved its value with universities â??laboratories, scientific and wind tunnels successful tests.
It can be used connected to a PC and to any system featuring a NMEA® input port.
CV7-E Ultrasonic Wind Speed Sensor Specification:
* Output rate: 4 Hz / 60 Hz measurement
* Wind module sensitivity: 0.12 m/s
* Wind module resolution: 0.05 m/s
* Wind module dynamic: 0.12 to 40 m/s
* Direction sensitivity: +/-1.5 degree
* Direction resolution: 1 degree
* Power supply: 8 V to 30 V DC
* Electrical consumption: 9 mA
* Op. temp. without icing: -15 degree C to +50 degree C
Y511-A Turbidity Sensor Description
Automatic cleaning turbidity sensor is complied with ISO 7027 Turbidity Standard. The turbidity sensor can be deployed in-situ and provide very stable data over long period of usage, which helps to ensure the quality of your measurements.
Y511-A Turbidity Sensor Typical Applications
Water quality monitoring, waste water testing, process water and aquaculture monitoring.
Y511-A Turbidity Sensor Features
* 0.1~1000 NTU
* Accuracy
MB7040 I2CXL-MaxSonar-WR
High Performance Ultrasonic Precision Rangefinder
MB7040 I2CXL-MaxSonar-WR Ultrasonic Rangefinder Product Description
Weather Resistant (IP67) Sensors, and Optional Chemical Resistance
The industrial outdoor I2CXL-MaxSonar-WR sensors have a robust PVC housing designed to meet IP67 water intrusion. The sensors provide short to long distance detection and ranging with a narrow beam pattern. The I2CXL-MaxSonar-WR outdoor ultrasonic sensors have high power output, noise rejection, auto calibration, and factory calibrated beam patterns.
In addition to the standard I2CXL-MaxSonar-WR, has developed the Fâ??Option for additional protection necessary in a few hazardous chemical environments. Extremely corrosive gases or liquids can degrade or compromise the operation of the sensing unit. As a result, we offer a more chemically inert seal which allows our sensors to operate in all but the harshest of chemical environments. In addition to the chemical resistance the sensor has improved performance in wet or dust environments.
MB7040 I2CXL-MaxSonar-WR Ultrasonic Rangefinder Product Specifiations
* Resolution of 1 cm
* Up to 40Hz reading rate
* RoHS Compliant
* Operates from 3.0-5.5V
* IP67 rated, I2C interface ultrasonic sensor
* Maximum range of 765 cm (300 inches)
* Operational Temperature from -40'C to +70'C
MB7040 I2CXL-MaxSonar-WR Ultrasonic Rangefinder Features and Benefits
* Low power consumption
* Narrow, controlled beam
* Easy to use interface
* Detects smaller objects
* Can be powered by many different types of power sources
MB7040 I2CXL-MaxSonar-WR Ultrasonic Rangefinder Applications and Uses
* People detection
* Security
* Motion detection
* Useable with battery power
* Autonomous navigation
* Educational and hobby robotics
* Collision avoidance
SONIC-ANEMO-MICRO Ultrasonic Wind Speed Sensor Description:
As a result of its very special electronic architecture the SONIC-ANEMO-MICRO shows a very low electrical consumption. It is ideal for remote stations or mobile installation.
SONIC-ANEMO-MICRO is an OEM sensor designed for integration in other original Equipment.
This sensor shows a very low consumption. It operates from 300µA.
SONIC-ANEMO-MICRO is the lowest consumption power solution of all LCJ sensors.
SONIC-ANEMO-MICRO Ultrasonic Wind Speed Sensor Specification:
Output data format: ASCII format, avaibility
Information transmited: Instant. W. Speed, Instant. W. Angle, avaibility
Output rate: select. 1 meas. and Tx: every 1,6 or 18 s
Wind module sensitivity: 0.12 m/s
Wind module resolution: 0.05 m/s
Wind module dynamic: 0.12 to 40 m/s
Direction sensitivity: +/-1.5 degree
Direction resolution: 1 degree
Power supply: 3 V to 3.6 V DC
Electrical consumption: 200µA avg
Op. temp. without icing: -15 degree C to +50 degree C
Cable: 50 cm / 4x0.22 mm2
Connection: 4 wires
Weight of the head: 100 gr
Weight of unit assembly: N/A
Mounting: N/A
CV7-V Ultrasonic Wind Speed Sensor Description
The CV7 is easily integrated into measurement and monitoring systems. The CV7-V is powered by 8-30 VDC power supply and it outputs RS232/RS422 (5V level signal) / NMEA0183.
CV7-V Ultrasonic Wind Speed Sensor Application
Static wind sensor
A conventional wind vane/anemometer features mechanical rotating parts. These moving parts expose the sensor to failure.
CV7 series was extensively tested in Marine applications for both precision and robustness.
Configurable wind sensor
CV7-V can be programmed and configured for : angle correction, smoothing time constant, units of measurement and interface format.
CV7-V connexion
CV7-V can be used connected to a PC and any systems featuring an NMEA® input port and specific pieces of equipment using conventional formats.
In PC mode, this bidirectional sensor can be set up for angle correction, damping, measure units and interface format.
Quality
All LCJ Capteurs are designed and manufactured in the Nantes region in France where they are fully tested throughout the manufacturing process.
CV7-V Ultrasonic Wind Speed Sensor Specification:
Output data format: NMEA0183; MWV, XDR
Information transmited: Instant. W. Speed, Instant. W. Angle, avaibility
Output rate: 2 Hz / 30 Hz measurement
Wind module sensitivity: 0.12 m/s
Wind module resolution: 0.05 m/s
Wind module dynamic: 0.12 to 40 m/s
Direction sensitivity: +/-1.5 degree
Direction resolution: 1 degree
Power supply: 8 V to 30 V DC
Electrical consumption: 9 mA
Op. temp. without icing: -15 degree C to +55 degree C
Cable: 25 m / 4x0.22 mm2
Connection: 4 wires
Weight of the head: 100 gr
Weight of unit assembly: 200 gr with mounting part
Mounting: Vertical ; 300 aluminium arm, 16 mm
1192 Electronic Sensors Suppliers
Short on time? Let Electronic Sensors sellers contact you.
