Sic uv photodiode sg01m-5lens
Concentrator lens sic based uv photodiode avirtual = 11.0 mm2
Properties of the sg01m-5lens sic uv photodiode
* broadband uva+uvb+uvc, ptb reported high chip stability, for very weak radiation
* radiation sensitive area a = 11.0 mm2
* to5 hermetically sealed metal housing with concentrator lens, 1 isolated pin and 1 case pin
* 10âµw/cm2 peak radiation results a current of approx. 140 na
Specifications
Typical responsivity at peak wavelength: 0.130/aw
Wavelength of max. Spectral responsivity: 280 nm
Responsivity range (s=0.1*smax): 221 - 358 nm
Sensitive area (chip size = 0.20 mm2): 11.0 mm2
Dark current (1v reverse bias): 0.7 fa
Capacitance: 50 pf
Short circuit (10uw/cm2 at peak): 140 na
Temperature coefficient: < 0.1 %/k
Operating temperature: -55 - +170 'c
Storage temperature: -55 - +170 'c
Soldering temperature (3s): 260 'c
Reverse voltage: 20 v
High speed carbon dioxide sensor ndir co2 sensor sprintir summary
Sprintir is a high speed (20 hz) co2 sensor, ideally suited for applications which require capture of rapidly changing co2 concentrations including metabolic assessment and analytical instrumentation.
Fast, accurate carbon dioxide sensor
The sprintir carbon dioxide sensor is the fastest, most accurate co2 sensor on the market. A breakthrough in ndir technology, the sprintir uses advanced solid state indium antimonide ledâ??s and detectors to offer a robust sensor with no moving parts, no heated filaments, and incredibly low power requirements. The sensor comes in four versions - from 0% to 100% - all capable of the same high-speed co2 measurement. This makes the sprintir especially useful in biological applications.
* high speed sensing (20hz)
* measurement ranges from 0 to 100%
* 3.3v supply
* low power requirement 35mw
* flow through adaptor (optional)
High speed carbon dioxide sensor ndir co2 sensor sprintir specifications
Measurement range: 0-5%, 0-20%, 0-60%, 0-100%
Accuracy: â±70 ppm +/- 5% of reading
Measurement noise:
Typical applications
* contactless measurement of surface temperatures or infrared radiation
* temperature measurement on moving objects
* continuous temperature control of manufacturing
* thermal alarm systems
* climate control
* medical instruments
* home appliances
Features
High accuracy
High sensitivity (110 V/W)
Low resistance (50 Kohm) and therefore
Very good signal-to-noise-ratio
Good response time (40 ms)
Low cost thin film technology
Introduction
The Smartec infrared sensors SMTIR9901 and SMTIR9902 are sophisticated full silicon infrared sensors which can be used in measuring the radiation temperature without any contact. For the different radiation temperature ranges various filters are available. The sensor type SMTIR9902 contains a temperature sensor for measuring the temperature of the sensor itself. The temperature range of the sensor-element is between - 40 to 100 'C. The sensor is available in a standard TO-05 encapsulation and with a 5.5. µm. high pass filter.
Easy and accurate measuring of the sensors temperature by means of a built-in temperature sensor (only for type SMTIR9902).
FS5001B series mass flow sensors are designed for general purpose flow monitoring and control applications. The sensors directly measure mass flow in the designed channel with trace flow detection capability. The lowest flow it can detect is 20 uL/min. These sensors can readily be applied for manifold flow assembly, leak detection, HVAC control, clean room air flow or nitrogen flush monitoring and control, environmental equipments such as air sampler, analytical instrumentation such as GC spectrometer.
FS5001 can be configured to measure flow full scale from 100 sccm to 1000 sccm (1 SLPM). With a full spectrum of customizable adaptors, it can be plug-and-play in many applications.
Features and Applications
- Low mass flow detectable from 0 ~ 200 sccm up to 0 ~ 1000 sccm
- Outstanding accuracy of 2.0%
- Response time < 10 ms
- Pressure rating up to 5 bar (73 psi)
- Output: analog or both analog and digital
FS7002 series mass flow/clog sensors can be used for open air space flow measurement or applied for clog sensing in an open space configuration. The sensor can measure air flow up to 10 m/sec with a fast response. The compact design make the installation an easy task. Examples are clog sensing in LCD projector; HVAC air flow monitoring, air fresher and fan status monitoring.
Features and Applications
- Measure open space air flow up to 10 m/sec
- Fast response < 20 msec
- Compact miniature design
- Excellent sensitivity
- Bi-direction capability
- Additional customization available
1192 Electronic Sensors Suppliers
Short on time? Let Electronic Sensors sellers contact you.
FS1015CL series mass flow sensors are specially designed for medical equipment flow monitor and control applications, and are made with world leading proprietary MEMS mass flow designed channel with a low pressure loss. The current models can be readily applied to ventilators and anesthesia equipments. These sensors can also be sterilized in medical liquids for reuse or hygienic purposes.
FS1015 Series can measure a flow up to 150 SLPM. ISO-15mm connection model is readily applicable to ventilators and/or anesthesia equipments.
Features and Applications
- MEMS thermal mass flow sensor
- Excellent rangeability with integrated multiple sensing elements
- High stability at null and full scale
- Fast response
- Low power consumption
- Low pressure loss
FS4003/08 series mass flow sensors are designed for general purpose flow monitor and control applications, and are made with world leading proprietary MEMS mass flow sensors and the smart electronic control system. The sensors directly measure mass flow in the designed channel with a low pressure loss. These sensors can readily be applied for electronics flow meters for anesthesia equipments, clean room air flow or nitrogen flush monitor and control, environmental equipments such as air sampler, analytical instrumentation such as GC spectrometer.
FS4008 can be configured to measure flow up to 50 SLPM. It can be applied for gas flow measurement and/or control equipments. Applications include electronic flow meter for anesthesia equipments, clean room gas flow monitor, air sampler, and gas analyzer.
Features and Applications
- Designed for 3 and 8 mm package
- Mass flow detectable from 0 ~ 2 SLPM to 0 ~ 50 SLPM
- Exchangeable connectors for easy installation
- Digital and analog output provide easy access for various communications
- Compact design ready for multiple channel assembly
- Excellent for electronic meters in anesthesia equipment
- Fast response and low power consumption
- Low pressure loss
FS4001 series mass flow sensors are manufactured using MEMS flow sensor and package technology. The sensors are specially designed for low flow rate range applications from 0 ~ 30 sccm up to 0 ~ 1000 sccm. The maximum flow rate for each model is manufactured via specially designed package as well as smart electronics so that the optimal sensitivity would be achieved.
Features and Applications
- Low mass flow range from 0 ~ 30 sccm up to 0 ~ 1000 sccm
- Outstanding accuracy of ±1.5 %
- Fast response (4 ms selectable)
- Pressure rating up to 5 bar (73 psi)
- Analog and/or digital user interface
- Easy installation
Typical Applications
* Contactless measurement of surface temperatures
* Temperature measurement of moving objects
* Remote measurement due to small angle of view
* Climate control
* Medical instruments
Introduction
The Smartec infrared sensor type SMTIR9902SIL is a standard Smartec SMTIR9902 sensor equipped with a silicon lens for measuring radiation temperatures within a small angle of view (7.27'). The SMTIR9902SIL contains a NI1000 temperature sensor for measuring the temperature of the sensor itself. The temperature range of this internal sensor is -20 to 100 'C. The sensor is mounted in a modified TO-05 encapsulation.
The Probe Range of zirconium dioxide oxygen sensors are available in three lengths. Suitable for aggressive and polluted applications such as boiler exhausts. Longer probes are an ideal solution for thicker walled, insulated flue pipes.
FEATURES
* Zirconium dioxide (ZrO2) sensing elements
* Long life, non-depleting technology
* Integral heating element
* High accuracy
* Requires an external interface board to operate
BENEFITS
* No reference gas required
* No need for temperature stabilisation
* Compact enclosure
OUTPUT VALUES
Oxygen pressure range 2mbar ~ 3bar max
Accuracy 5mbar max
Internal operational temperature 700'C
Response time (10 - 90% step)
Standard response sensor < 15s
Fast response sensor < 4s
Warm up time (prior to sensor operation) 60s
Warm up time (from standby) 20s
Output stabilisation time ~ 180s
SO-E2-960
Limiting Current Type Sensor Oxygen Sensors
When voltage is applied to a zirconia electrolyte cell, oxygen is pumped through the zirconia disc from the cathode side to the anode side because the carriers of the current flowing through the zirconia electrolyte are oxygen ions. By attaching a cap with a pinhole on the cathode side of the cell and by increasing the voltage over the cell the current shows saturation due to the rate limiting step in the transfer of oxygen to the cathode. This saturation current is called limiting current and is nearly proportional to the ambient oxygen concentration.
Below the advantages of the oxygen sensor:
measuring range 1.00 to 96.0 vol.% oxygen
High accuracy
For many types a more or less linear characteristic
Small temperature dependence of the sensor signal
Low interference with other gases
Long service life
In many cases "Single point calibration" necessary only once
Applications:
Medical
Laboratory
Food industry
Household/Gastronomy
Measuring technique
Security technology/Monitoring
(Electrical-) industry
Characteristic Data:
Measuring gas: Oxygen concentration
Measuring medium: Gaseous atmosphere
Measuring principle: Limiting current type sensor
Measuring ranges: 1.00 - 96.0 vol.% O2
Response time (t90): 2 to 25 sec. (Depends on: sensor type, gas flow, measuring chamber)
Sensor voltage / heating voltage / power consumption / heater cold resistance
Sensor voltage: 0.7 to 1.6 Volt
Heating voltage: 3.6 - 4.4 Volts
Power consumption: 1.3 to 1.8 Watts (depends on application and packaging)
Cold resistance: R( 25'C ) = 3.25 ohm ± 0.20 ohm
Warm up time: Min. 30 s
FEATURES
* Zirconium dioxide (ZrO2) sensing elements
* Long life, non-depleting technology
* Integral heating element
* High accuracy
* Requires an external interface board to operate
BENEFITS
* No reference gas required
* No need for temperature stabilisation
* Two lengths available; 220mm and 400mm
TECHNICAL SPECIFICATIONS
Heater voltage
Operating 4V DC ± 0.1V DC (1.7A)
Standby 1.65V DC (0.7A)
Pump impedance at 700'C < 6kohm
Permissible gas temperature
Standard temperature -100'C to +250'C
High temperature -100'C to +400'C
Gas flow rate 0 - 10 m/s
Repetitive permissible acceleration 5g
Incidental permissible acceleration 30g
OUTPUT VALUES
Oxygen pressure range 2mbar - 3bar max
Accuracy 5 mbar max
Internal operational temperature 700'C
Response time (10 - 90% step) < 15s
Warm up time (prior to sensor operation) 100s
Warm up time (from stand by) 20s
Output stabilisation time ~ 180s
MB1240
XL-MaxSonar-EZ4
High Performance Ultrasonic Rangefinder
Product Description
The XL-MaxSonar-EZ4 has the highest noise tolerance and narrowest beam of any of our indoor sensors. The sensor is designed and calibrated to provide reliable range information to large targets even in environments with strong acoustic or electrical noise sources.
MB1240 Features and Benefits
* Narrowest beam in the XL-MaxSonar-EZ/AE sensor line
* Low power consumption
* Easy to use interface
* Large target detection
* Acoustic noise rejection
* 3.3v to 5.5v operational voltage
MB1240 Applications and Uses
* Great for people detection
* Security
* Motion detection
* Recommended for multi-copters and UAV's
* Used with battery power
* Autonomous navigation
* Educational and hobby robotics
* Collision avoidance
Mb7389
Hrxl-maxsonar-wrmt
High performance ultrasonic precision rangefinder
Product description
The hrxl-maxsonar-wrmt ignores smaller targets and only reports the range to target with the largest acoustic return. This is our most advanced weather resistant sensor designed for target detection and ranging outdoors or in tank or bin applications.
Mb7389 features and benefits
* factory calibrated beam width
* low operating voltages from 2.7v to 5.5v
* all range outputs are active simultaneously
* superior clutter rejection
Mb7389 applications and uses
* bin level measurement
* tank level measurement
Humidity Module HTG3513CH Voltage Output Humidity Sensor
DESCRIPTION
Based on the rugged HUMIREL humidity sensor, HTG3513CH is a dedicated humidity and temperature plug and play transducer designed for OEM applications where a reliable and accurate measurement is needed. Direct interface with a micro-controller is made possible with the module's humidity linear voltage and direct NTC outputs. HTG3513CH is designed for high volume and demanding applications.
FEATURES
* Voltage Supply: 3.3 Vdc
* Nominal Output @55%RH: 1.462 - 1.568 V
* Humidity Average Sensitivity: +18 mV/%RH
* Current consumption: 1.0 mA dc
* Humidity Measuring Range: 0 - 100 %RH
* Humidity Operating Range: 0 - 100%RH
* Temperature Operating Range: -40 - 110'C
* Suitable for small bulk assembly
* Product free from Lead, Cr (6+), Cd and Hg. Compliant with RoHS
* Full interchangeability. Better than +/-3%RH and +/-0.25'C
* Humidity calibrated within +/- 3% RH @ 55% RH
* Temperature measurement through NTC direct output
* Demonstrated reliability and long term stability
* Reliability not affected by repeated condensations
APPLICATIONS
* Automotive
* Home Appliance
* Printers
HTG3535CH Humidity and Temperature Sensor Module with voltage output
DESCRIPTION
Based on the rugged HUMIREL humidity sensor, HTG3535CH is a dedicated humidity and temperature plug and play transducer designed for OEM applications where a reliable and accurate measurement is needed. Direct interface with a micro-controller is made possible with the moduleâ??s humidity linear voltage and direct NTC outputs. HTG3515CH is designed for high volume and demanding applications.
FEATURES
* Voltage Supply: 5 Vdc
* Nominal Output @55%RH: 2.401 - 2.559 V
* Humidity Average Sensitivity: +26 mV/%RH
* Current consumption: 1.2 mA dc
* Humidity Measuring Range: 0 - 100 %RH
* Humidity Operating Range: 0 - 100%RH
* Temperature Operating Range: -40 - 110'C
* Suitable for small bulk assembly
* Product free from Lead, Cr (6+), Cd and Hg. Compliant with RoHS
* Full interchangeability. Better than +/-3%RH and +/-0.25'C
* Humidity calibrated within +/- 3% RH @ 55% RH
* Temperature measurement through NTC direct output
* Demonstrated reliability and long term stability
* Reliability not affected by repeated condensations
APPLICATIONS
* Automotive
* Home Appliance
* Printers
Frequency Output Temperature and Humidity Sensor HTF3226LF
DESCRIPTION
Based on the rugged HS1101LF humidity sensor, HTF3226LF is a dedicated humidity and temperature transducer designed for OEM applications where a reliable and accurate measurement is needed. It features a miniature connector for easy, cost-effective mechanical mounting. Direct interface with a micro-controller is made possible with the moduleâ??s linear frequency output.
FEATURES
* Full Lead free product
* Calibrated within +/-5% @55%RH
* Small size and very cost effective
* Miniature connector (JST)
* 10kOhms +/-3% NTC temperature sensor (1% optional)
* The best combination of cost effectiveness and performance
* Stable, linear proportional frequency output from 10% to 95%RH
* Stable and reproducible characteristics with temperature
* High reliability and long term stability
Humidity Sensor Specific Features
* Instantaneous de-saturation after long periods in saturation phase
* Fast response time
* High resistance to chemicals
* Not affected by water immersion
* Patented solid polymer structure
Temperature Sensor Specific Features
* High quality thermistor
* Stable
* High sensitivity
Voltage Output Temperature and Humidity Sensor HTG3515CH
DESCRIPTION
Based on the rugged HUMIREL humidity sensor, HTG3515CH is a dedicated humidity and temperature plug and play transducer designed for OEM applications where a reliable and accurate measurement is needed. Direct interface with a micro-controller is made possible with the module's humidity linear voltage and direct NTC outputs. HTG3515CH is designed for high volume and demanding applications.
FEATURES
* Voltage Supply: 5 Vdc
* Nominal Output @55%RH: 2.401 - 2.559 V
* Humidity Average Sensitivity: +26 mV/%RH
* Current consumption: 1.2 mA dc
* Humidity Measuring Range: 0 - 100 %RH
* Humidity Operating Range: 0 - 100%RH
* Temperature Operating Range: -40 - 110'C
* Suitable for small bulk assembly
* Product free from Lead, Cr (6+), Cd and Hg. Compliant with RoHS
* Full interchangeability. Better than +/-3%RH and +/-0.25'C
* Humidity calibrated within +/- 3% RH @ 55% RH
* Temperature measurement through NTC direct output
* Demonstrated reliability and long term stability
* Reliability not affected by repeated condensations
APPLICATIONS
* Automotive
* Home Appliance
* Printers
Description:
Based on the rugged HS1101LF humidity sensor, HTF3000LF is a dedicated humidity and temperature transducer designed for OEM applications where a reliable and accurate measurement is needed. It features a very small size for easy, cost-effective mechanical mounting. Direct interface with a micro-controller is made possible with the module's linear frequency output.
Product Description
The weather resistant SCXL-MaxSonar-WR selfâ??cleaning sensor is a rugged ultrasonic sensor component module. This outdoor sensor provides very short to long distance detection and ranging in a compact, robust PVC housing. The ultrasonic sensor meets the IP67 water intrusion standard and matches standard electrical 3/4-inch PVC pipe fittings.
MB7589 Features and Benefits
* Factory calibrated beam width
* Low operating voltages from 2.7V to 5.5V
* All range outputs are active simultaneously
* Superior clutter rejection
MB7589 Applications and Uses
* Bin Level Measurement
* Tank Level Measurement
z
1192 Electronic Sensors Suppliers
Short on time? Let Electronic Sensors sellers contact you.
