Find Verified Electric Motors Suppliers, Manufacturers and Wholesalers

Type: VHS5006TP-4-350P
Power: 350HP
Rated speed: 1780rpm
Insulation Class: F
Duty Cycle: S1
Standard: NEMA
Frequency: 60Hz

ZZJ-800 DC Motor
ZZJ-800 series motor is a DC motor for metallurgical lifting, suitable for rolling mills, cranes, elevators and electric shovels.
Structure:

1. The base adopts a thin-plate polygonal lamination structure, small size and light weight. The stator and rotor are treated with vacuum pressure paint (VPI), with good insulation and electrical conductivity.

2. Standard rated voltage: 220V, 440V.

3. Rated speed: 1025, 900, 800, 725, 650, 550r / min, etc.

4. Protection features: IP23S, IP44.

5. Installation method: IC01, IC06, IC17, IC37 and ICW37A86

6. Insulation class: Class F

7. The data listed in the technical data table should be under the following conditions;

a. The altitude does not exceed 1000 meters;

b. The ambient air temperature is between -30 â?? and 40 â??;

c. The working environment should be free of acidic, alkaline or other gases that have a corrosive effect on the insulation; there should be no explosive or flammable gases.

d. Continuous working system: SI; S2; S3.
Plz check the link for more details.

Power range:1250-2500 kw,2000kw-10000kw,10mw-50mw-100mw.
Rated armature voltage: 660, 750, 850, 950, 1000V,3000V
excitation: Other
Axis height:810 to 1000mm-5000mm
speed: Up to 1000 rpm

Permanent magnet motor

KYT series (IP55) compressor special ultra-efficient permanent magnet variable frequency motor
Frame center height: H160 ~ H355
Rated output power: 15kW ~ 250kW
This series of motors uses permanent magnet motors made of rare earth permanent magnet materials. The rotor has achieved rare earth permanent magnetization, no slip, no fundamental iron in the rotor, copper loss and less heat generation, which reduces stator current and stator resistance losses. Especially at low speeds, high motor efficiency can still be maintained.

SYNCHRONOUS MOTOR
Basic model: T, TKS, TD
Armature diameter:  1200-  3550mm
Power: 200 800000Kw
Number of poles: 2-40
Voltage: 690 15000V
Frequency: 50HZ, 60HZ
Protection level: IP23, IP44, IP54, IP55
Cooling method: IC01, IC611, IC81W

Because synchronous motors can operate at advanced power factors by adjusting the excitation current, it is beneficial to improve the power factor of the power grid. Therefore, large equipment, such as large blowers, water pumps, ball mills, compressors, rolling mills, etc., are often driven by synchronous motors. This advantage is particularly prominent when low-speed large equipment uses synchronous motors. In addition, the speed of the synchronous motor is completely determined by the power frequency. When the frequency is constant, the speed of the motor is also constant, and it does not change with the load. This feature is of great significance in certain transmission systems, especially multi-machine synchronous transmission systems and precision speed regulation and speed stabilization systems. The running stability of synchronous motors is also relatively high. Synchronous motors generally operate in an over-excited state, and their overload capacity is greater than that of corresponding asynchronous motors. The torque of an asynchronous motor is proportional to the square of the voltage, while the torque of a synchronous motor is determined by the product of the voltage and the internal electromotive force generated by the motor's exciting current, which is only proportional to the first power of the voltage. When the grid voltage suddenly drops to about 80% of the rated value, the torque of the asynchronous motor often drops to about 64% and stops running because it does not move the load; while the torque of the synchronous motor does not drop much, it can also be forced by Excitation to ensure stable operation of the motor

VHS-Motor
Effiziente vertikale NEMA-Hohlwellenmotoren
VHS445TP-4-250S Zus�¤tzlicher Abw�¤rtsschub: 9800 (lb) 1500 U / min

VHS Motor
NEMA Premium Efficient Vertical Hollow-shaft Motors
VHS445TP-4-250S Extra Downthrust: 9800(Lb) 1500RPM
VHS IP55 TEFC 380 VOLT 50 HZ;With TERMINAL BOX
SERVICE FACTOR 1.15;PT 100 2 SETS OF 3 ELEMENTS
MAIN TERMINAL BOX HEATER GUIDE BEARING PT 100 MOTOR HEATER
TRUST BEARING PT 100 DIAL SCALE,IP55 TEFC,Top cover red,Body Grey color Working altitude 1500m NSK or SKF bearing Included heaters, sensors and boxes

VHS Motor ylb motor
NEMA Premium Efficient Vertical Hollow shaft Motors
VHS447TP-4-300S Extra Downthrust: 9800(Lb) 1500RPM
VHS IP55 TEFC 380 VOLT 50 HZ;With TERMINAL BOX
SERVICE FACTOR 1.15;PT 100 2 SETS OF 3 ELEMENTS
MAIN TERMINAL BOX HEATER GUIDE BEARING PT 100 MOTOR HEATER
TRUST BEARING PT 100 DIAL SCALE,IP55 TEFC,Top cover red,Body Grey color Working altitude 1500m NSK or SKF bearing Included heaters, sensors and boxes

VHS Motor vertical motor
NEMA Premium Efficient Vertical Hollow shaft Motors
VHS284TP-4-025P Extra Downthrust: 3200 (Lb) 1500RPM
VHS IP55 TEFC 380 VOLT 50 HZ;With TERMINAL BOX
SERVICE FACTOR 1.15;PT 100 2 SETS OF 3 ELEMENTS
MAIN TERMINAL BOX HEATER GUIDE BEARING PT 100 MOTOR HEATER
TRUST BEARING PT 100 DIAL SCALE,IP55 TEFC,Top cover red,Body Grey color Working altitude 1500m NSK or SKF bearing Included heaters, sensors and boxes

JK, JS, JR, JS2, JR2, JSL, JRL series medium-sized motors are used to drive a variety of different machinery, such as fans, compressors Machines, water pumps, crushers, coal mills, cutting machine tools, transportation machinery and other equipment, and can be used as prime movers in coal mines, machinery industries, power plants and various industrial and mining enterprises.
6 Ordering instructions Please indicate the following when ordering

a. Motor model: (JS158-4)

b. Rated frequency: (50Hz/60HZ)

c. Rated power: (10KW-680kW-5000KW-100MW)

d. Rated voltage: (460-6KV-10KV-20KV)

e. Number of poles: (2-4-18 poles)

f. Outlet box position (right side of the motor [looking at the end of the motor shaft extension]

Power : 100HP-1000HP; 1200HP-5000HP,10MW-100MW.
YL series 6KV, 10kV medium and large high-voltage vertical three-phase asynchronous motors (hereinafter referred to as motors) are our company using domestic and foreign advanced technology, combined with our company's decades of practical experience in producing high-voltage motors, in accordance with international standards, national standards and industries A series of optimized products developed as standard. It can also be treated by anti-corrosion and anti-mildew technology to derive outdoor (W) and outdoor anti-corrosion (WF) motors. This series of motors can be used directly on 10kV power grids, which has the advantages of simplifying equipment, saving investment, reducing energy consumption and so on.

Vertical hollow shaft motor:
Model No: VHS315-3-4
Power: 300HP
Rated speed: 1780rpm
Insulation Class: F
Duty cycle: S1
Frequency: 60Hz/50Hz
IEC standard

JK, JS, JR, JS2, JR2, JSL, JRL series medium-sized motors are used to drive a variety of different machinery, such as fans, compressors

Machines, water pumps, crushers, coal mills, cutting machine tools, transportation machinery and other equipment, and can be used as prime movers in coal mines, machinery industries, power plants and various industrial and mining enterprises.

Model: PREMIUM EFFICIENT SEVERE DUTY MOTOR, 10 HP, 1800 RPM, 208-230 / 460V, 215TC FRAME, C-FACE WITH FEET Model Number: PEWWE10-18-215TC; Voltage: 230/460 V; Chadal: 10 HP; torque: 1760 rpm; Degree of protection: IP55; APC: 0.92;
Ambient temperature: -30 - +40 C; working height: 1300 m;
-With Special grease for -30C
-No Thermal protection
-Terminal box position F1
-With foot and flange C-Face (AJ=7.250 AK=8.500 BD=8.875 )

model: YA, YAKS, YAKK
Machine seat number: H355-H1120
Power: 160 -25000Kw
Number of poles: 2-24
Voltage: 690 - 11000V
Frequency: 50HZ, 60HZ
Explosion-proof grade Exe II T1, Exe II T2, Exe II T3
Protection level: IP44, IP54, IP55, IP56
Cooling method: IC511, IC516, IC611, IC616, IC666, IC81W, IC86W

Product Description

Basic model: Y, YKS, YKK,YR,YRKK

Machine seat number: H355-H1120

Power: 160 - 25000Kw

Number of poles: 2-24

Voltage: 415V - 15000V

Frequency: 50HZ, 60HZ

Protection level: IP23, IP44, IP54, IP55

Cooling method: IC01, IC611, IC616, IC81W, IC86W

Standard design data

Standard GB755 IEC

Voltage 380V (400-450mm), 660V (500-560mm)

Cooling method IC416 (independent axial fan, or centrifugal fan)

Independent fan voltage three-phase, 380V

Frame size 400-560mm

Rated frequency 50HZ

Insulation class F

Installation form IMB3

Working method S3-40% for lifting and metallurgy

Protection class IP54

Overload multiple At rated voltage and rated frequency, 150% rated current is allowed to overload for 1 minute

Altitude does not exceed 1000m

Product Description

Basic model: Y, YKS, YKK,YR,YRKK

Machine seat number: H355-H1120

Power: 160 - 25000Kw

Number of poles: 2-24

Voltage: 415V -15000V

Frequency: 50HZ, 60HZ

Protection level: IP23, IP44, IP54, IP55

Cooling method: IC01, IC611, IC616, IC81W, IC86W

Machine seat number: ZD180-ZD350
Power: 50-3000KW 2800-6000kW
Speed:100/300/600/800/1500/1800rpm
Voltage: 660 1200V
Torque range: 90 1500kNm
Protection level: IP23, IP44
Cooling method: IC06, IC17, IC37, IC81W

The Z series large DC motor is a new product developed by our company. The new design has the characteristics of large output power, low noise, small vibration, high efficiency, high reliability, and good safety performance.

Power range:1250-2500 kw,2000kw-10000kw,10mw-50mw-100mw.
Power range:1250-2500 kw,2000kw-10000kw,10mw-50mw-100mw.â??â??â??â??â??â??â??
Rated armature voltage: 660, 750, 850, 950, 1000V,3000V
excitation:Other
Axis height:810 to 1000mm-5000mm
speed:Up to 1000 rpm

WEG W22 200 HP-150kw Poles: 6P
586 / 7TZ 3Ph 460 V 50 Hz IC411 - TEFC
WEG 2.2kw 3hp 3 Phase 6 Pole Mte16a Al Ip55 Al112m
WEG, W22 IE3 7.5 kW 4P 132M 3Ph 380- 415/660 // 460 V 50 Hz
WEG, 3 HP-2.2kw, 1800 RPM, 208-230 / 460V, 182TC FRAME
WEG, 10 HP-7.5kw, 3-Phase, 1760rpm, 208- 230 / 460V, 213 / 5TC Frame
WEG, 10 HP-7.5kw, 1800 RPM, 208-230 / 460V, 215TC FRAME

JK, JS, JR, JS2, JR2, JSL, JRL series medium-sized motors are used to drive a variety of different machinery, such as fans, compressors
Motor model: (JS158-4)
Rated frequency: (50Hz/60HZ)
Rated power: (10KW-680kW-5000KW-100MW)
Rated voltage: (460-6KV-10KV-20KV)
Number of poles: (2-4-18 poles)

Power : 100HP-1000HP; 1200HP-5000HP,10MW-100MW.

YL series 6KV, 10kV medium and large high-voltage vertical three-phase asynchronous motors (hereinafter referred to as motors) are our company using domestic and foreign advanced technology, combined with our company's decades of practical experience in producing high-voltage motors, in accordance with international standards, national standards and industries A series of optimized products developed as standard. It can also be treated by anti-corrosion and anti-mildew technology to derive outdoor (W) and outdoor anti-corrosion (WF) motors. This series of motors can be used directly on 10kV power grids, which has the advantages of simplifying equipment, saving investment, reducing energy consumption and so on.