ES MIG 80S-G is a 0.5Mo-alloyed, solid wire for the GMAW of creep-resistant steels of the same composition, like those used for pipes in press-ure vessels and boilers with a service tempera-ture of up to 500�°C.
ES MIG 80S-G is taking MAG welding operations to new levels of performance and all-round ef�ciency, especially in robotic and mechanised welding.
Characteristic features include excellent start properties; trouble-free feeding at high wire speeds and lengthy feed distances; a very stable arc at high welding currents; extremely low levels of spatter; low fume emission; reduced contact tip wear and improved protection against corrosion of the wire.
Wire connection clips are used in suspended ceiling systems to fasten the secondary furring channel to the main C- 38 channel. GaccessoriesTM wires are designed to have a thickness of 2 to 3mm and can bear up to 25 kg.
Advantages:
Ceiling System
steel wire for prestressed concrete
mainly includes three types according
to the surface treatment: plain PC
wire, spiral PC wire and indented PC
wire. And the reference standards: GB/
T5223, ASTMA421, BS5896, JISG3536,
EN10138 or other special standards.
331 Titanium Wire Suppliers
Short on time? Let Titanium Wire sellers contact you.
High carbon steel wire from mattress spring (Bonnell and Pocket)
Material :AISI 1045,1060,1065,1070,1072
Wire diameter : 1.2mm-5mm
Tensile Strength : 1550- 1850 MPA
Gosay Sunscreen Gel SPF 50+ is an advanced multi-spectrum broad-spectrum sunscreen formulated with a high-performance combination of organic (chemical) and inorganic (physical/mineral) UV filters including Octocrylene, Ethylhexyl Methoxycinnamate, Butyl Methoxydibenzoylmethane, Zinc Oxide, and Titanium Dioxide. Enriched with skin-nourishing antioxidants (Tocopheryl Acetate / Vitamin E), intense humectants (Panthenol, Sodium Hyaluronate, Glycerin, Urea, Trehalose), and soothing conditioning agents (Niacinamide, Serine), this lightweight gel provides comprehensive UVA/UVB protection, anti-aging defense, and deep hydration without leaving a greasy residue. Approved and registered by the Egyptian Drug Authority (EDA).
Ilmenite consists of iron oxide and titanium and is considered as the main source of titanium dioxide, titanium sponge, and titanium ingots, used in important strategic industries such as manufacture of aircraft structures, missiles, submarines , space vehicles .
ES FC 308LT is a rutile, fux-cored wire, speci�cally designed to operate in the vertical and overhead positions when welding 304, 304L, 308 and 308L stainless steels.
The stabilised 321 and 347 steels may also be welded.
Typical application: welding 304L and other common 18/8 stainless steels, Nitrogen bearing 304LN and titanium stabilized 321 and General fabrication including piping, tanks, and pressure vessels
* Helical wire diameter : 1.30mm - 1.50mm.
* Coils per m2 : 100-225 Units.
*Bonnell spring end ring : 62mm - 95mm.
*Bonnell spring wire diameter 1.80mm - 2.40mm.
*Bonnell spring turns : 4-7 turns.
*Bonnell spring height :70-210mm.
*Frame :round wire 4.5 - 5.00mm.
*Packing : press packed ( with frame, 15-25 unit per pallet pack )
or roll packed ( without frame, 5 - 15 unit per roll )
* Pocket spring diameter : 35mm - 70 mm.
* Pocket spring wire diameter : 1.20mm - 2.20mm.
* Coils per m2 : 200- 700 Unit ( according to customer request ).
* Pocket spring height : 50mm - 210mm.
* Top and bottom with / without Nonwoven.
* Packing : roll Packed ( 5-10 Units, Roll Pack ).
Egyptian Chinese Black Sand supplies Ilmenite Sand from Egypt for international buyers, mineral processors, and industrial manufacturers. Ilmenite is an important titanium-bearing mineral and is widely used as a raw material for titanium dioxide production and other titanium-related industrial applications.
We offer ilmenite according to the buyer's required technical specifications, quantity, packaging, and delivery terms. Detailed technical specifications and Certificate of Analysis (COA) can be provided to serious buyers upon request.
Product Information
Product: Ilmenite Sand
Origin: Egypt
Mineral: Ilmenite
Source: Egyptian Black Sand
Color: Black to dark brown
Form: Sand / Granular
Application: Titanium dioxide production and titanium-related industries
Quantity: Available according to buyer requirements
Packing: Bulk / Jumbo Bags / Customized packing
Loading: Egyptian ports
Trade Terms: FOB / CFR / CIF
Inspection: Third-party inspection available upon agreement
Documentation: COA, commercial invoice, packing list and export documentation available
Applications
Egyptian Ilmenite can be used in:
Titanium dioxide (TiO) production
Titanium pigment manufacturing
Titanium metal and titanium compounds
Welding electrode manufacturing
Abrasive and specialized industrial applications
Other titanium-related industrial processes
Why Buy from Egyptian Chinese Black Sand?
Egyptian origin
Direct supplier/exporter
Bulk quantities available
Competitive international pricing
Technical specifications available
Flexible packaging options
FOB / CFR / CIF export options
Long-term supply agreements available
Professional export documentation
Cable gland IP 65 with stress relief metric threaded connection. Fiber glass polymide Impact & temperature resistant Grey RAL 7035 Available in different Dimensions
ES MIG 70S-3 is a copper-coated, Mn-Si-allo-yed G2Si/ER70S-3 solid wire for the GMAW of non-alloyed steels, as used in general construction, pressure vessel fabrication and shipbuil-ding.
The wire has a carefully controlled wire chemistry and a unique surface technology providing superior weld-metal quality at high wire feed speeds and at high welding currents.
The wire can be used with both Ar/CO2 mixed gas and pure CO2 shielding gas.
ES MIG 80S-Ni1 is a 0.9Ni-alloyed (ER80S-Ni1), copper-coated, solid wire for the GMAW of low-temperature, ne-grained steels.
The wire provides good impact toughness down to -50C and is especially suitable for use in the construction of offshore platforms, pressure vessels, and pipelines.
ES FLUX 161 is designed for the single-wire, multi-run butt welding of mild, medium and high tensile steels with impact strength requirements down to -40C/-60C.
Due to the non-alloying effect, ES FLUX 161 is designed for use with a suitable alloying wire. ES FLUX 161 can be used on DC.
ES 71T1C is a Fux-cored, tubular wire for all-positional welding using either Ar/CO2 or CO2.
The wire is suitable for all mild and medium tensile structural steels.
The running characteristics are exceptional, using the spray mode of transfer, and this applies equally to both shielding gases. ES 71T1C is also universally approved to grade 3 by all major authorities.
ES SG2 is a bare Mn-Si-alloyed G3Si1/ER70S-6 solid wire for the GMAW of non-alloyed steels, as used in general construction, automotive components, pressure vessel fabrica tion and shipbuilding.
ES SG2 taking MAG welding oper-ations to new levels of performance and all-round ef�ciency, especially in robotic and mechanised welding. Characteristic features include excellent start properties; trouble-free feeding at high wire speeds and lengthy feed dis- tances; a very stable arc at high welding currents; extremely low levels of spatter; low fume emission; reduced contact tip wear and improved protection against corrosion of the wire.
ES MIG 80S-G is a 0.5Mo-alloyed, solid wire for the GMAW of creep-resistant steels of the same composition, like those used for pipes in press-ure vessels and boilers with a service tempera-ture of up to 500�°C.
ES MIG 80S-G is taking MAG welding operations to new levels of performance and all-round ef�ciency, especially in robotic and mechanised welding.
Characteristic features include excellent start properties; trou- ble-free feeding at high wire speeds and lengthy feed distances; a very stable arc at high welding currents; extremely low levels of spatter; low fume emission; reduced contact tip wear and improved protection against corrosion of the wire.
ES 81T1-Ni1M is an all-positional, rutile, fux- cored wire for good toughness down to -40C.
The wire contains 1% nickel and has exceptional operating characteristics in all positions with high deposition rates. Shielding gas Ar + 20% CO2 or CO2. ES 81T1-Ni1M is designed for the all-posit-ional welding of carbon-manganese and low-alloy steels.
Typical applications: offshore fabrications, vessels and structural steel work.
ES EA2 is a copper-coated, molybdenum-alloyed wire for the submerged arc welding of non-alloyed and low-alloyed steels.
ES EA2 Submerged arc welding wire (SAW) used for joining fine grain steels resistant to high temperatures, structural steels, construction naval vessels, pressure vessels, shipbuilding steels, pipes and pipeline steels up to grade X70, etc.
ES EA2 can be combined with ES FLUX 161, ES FLUX 171 and ES FLUX 181.
ES MIG 309LSi a continuous, solid ,corrosion-resistant, chromium-nickel wire for welding steels with a similar composition, wrought and cast steels of the 23% Cr -12% Ni types.
The alloy is also used for welding buffer layers on C/Mn steels and welding dis similar joints.
When using the wire for buffer layers and dissimilar joints, it is necessary to control the dilution of the weld.
ES MIG 309LSi has good general corrosion resistance.
The higher silicon content improves the welding properties such as wetting.
ES MIG 309LSi a continuous, solid ,corrosion-resistant, chromium-nickel wire for welding steels with a similar composition, wrought and cast steels of the 23% Cr -12% Ni types.
The alloy is also used for welding buffer layers on C/Mn steels and welding dis similar joints.
When using the wire for buffer layers and dissimilar joints, it is necessary to control the dilution of the weld.
ES MIG 309LSi has good general corrosion resistance.
The higher silicon content improves the welding properties such as wetting.
ES SG3 is a bare Mn-Si-alloyed G4Si1/ER70S-6 solid wire for the GMAW of non-alloyed steels, as used in general construction, automotive components, pressure vessel fabrica tion and shipbuilding.
It has a slightly higher manganese and silicon content than ES SG2 to increase the weld metal strength.
This also promotes a low sensitivity to surface impurities and contributes to smooth, sound welds.
ES SG3 taking MAG welding operations to new levels of performance and all-round ef�ciency, especially in robotic and mechanised welding.
Characteristic features include excellent start properties; trouble-free feeding at high wire speeds and lengthy feed distances; a very stable arc at high welding currents; extremely low levels of spatter; low fume emission; reduced contact tip wear and improved protection against corro- sion of the wire.
ES 71T1M is a fux-cored, tubular wire designed as a truly all-positional, general-purpose wire for welding mild and medium tensile steels up to 510 MPa tensile strength.
Using either Ar/CO2 or CO2 as the shielding gas, the 1.2 and 1.4 mm sizes can be used in the vertical position on spray transfer providing for maximum deposition and time savings.
Weld pool control is easy both vertically up and downwards and slag removal is rapid. ES 71T1M is designed for a wide range of applications especially where manipulation of the work is impractical.
End Hooked Steel Fiber 1.0/50 is a low carbon, cold-drawn steel wire designed to reinforce slab on grade concrete and enhance reinforced constructional elements with shrinkage crack control, improve shear resistance, and increase tensile and flexural strengths.
Advantages:
-Prevent cracks due to early-age shrinkage .
-Better cohesion in the fresh concrete.
-Increase flexural strength and shear resistance.
-Improve load capacity and concrete ductility.
-Increase abrasion, fatigue resistance.
-Enhance concrete in its hardened state.
-Provide ultimate performance under intense conditions
Usage:
-Industrial floor slabs
- Warehouses , Factories.
-Commercial and Residential S.O.G. and screed flooring.
-Bridge decks, overlays and pavements.
-Concrete Roads, Parking Areas .
-Precast concrete applications and slabs on pile.
-Shotcrete.
-Tunnel, linings and slope stabilizations .
-Mass concrete and composite deck construction.
-Military Purposes
ES 71T1M is a Fux-cored, tubular wire designed as a truly all-positional, general-pur pose wire for welding mild and medium tensile steels up to 510 MPa tensile strength.
Using either Ar/CO2 or CO2 as the shielding gas, the 1.2 and 1.4 mm sizes can be used in the vertical position on spray transfer providing for maximum deposition and time savings.
Weld pool control is easy both vertically up and downwards and slag removal is rapid.
ES 71T1M is designed for a wide range of applications especially where manipulation of the work is impractical.
ES EA4 is a manganese-alloyed, copper coa-ted wire for the submerged arc welding of medium- and high-strength structural steels.
ES EA4 should preferably be used together with non-alloying or slightly alloying fuxes, such as ES FLUX 161, when high weld metal quality requirements must be met.
ES EA4 Submerged arc welding wire (SAW) for joining fine grain and high temperature resistant steels, structural steels, steels for shipbuilding, steels for pressure vessels, production of steel pipes up to grade X80, high-strength steels, etc.
ES EA4 can be combined with ES FLUX 161, ES FLUX 171 and ES FLUX 900.
ES EL12 is a copper-coated, mild steel wire for submerged arc welding.
It can be combined with the following fluxes:
ES FLUX 171, ES FLUX 180
ES FLUX 181 and ES FLUX 900.
ES EL12 is especially for use in combination with ES FLUX 180 and ES FLUX 181 in the shipbuilding industry, for the butt welding in material from 10 to 30 mm thickness and especially thin plate (e.g. LPG cylinder).
ES FLUX 900 is a basic agglomerated, slightly Si- and Mn-alloying fux for submerged arc welding, specially designed for fillet welding and for the single- and multi-pass butt welding of mild, medium and high tensile steels.
ES FLUX 900 is of the aluminate basic type and, for this slag system, it has a very high current-carrying capacity on both AC and DC and very good operating characteristics.
ES FLUX 900 is ideally suited to narrow gap welding due to the excellent slag detachability and smooth side-wall blending.
ES FLUX 171 is a basic agglomerated, slightly Si- and Mn-alloying fux for submerged arc welding, specially designed for fillet welding and for the single- and multi-pass butt welding of mild, medium and high tensile steels.
ES FLUX 171 is of the aluminate basic type and, for this slag sys- tem, it has a very high current-carrying capacity on both AC and DC and very good operating characteristics.
ES FLUX 171 is ideally suited to narrow gap welding due to the excellent slag detachability and smooth side-wall blending.
ES FLUX 900 is a basic agglomerated, slightly Si- and Mn-alloying fux for submerged arc welding, specially designed for fillet welding and for the single-and multi-pass butt welding of mild, medium and high tensile steels. ES FLUX 900 is of the aluminate basic type and, for this slag system, it has a very high current-carrying capacity on both AC and DC and very good operating characteristics.
ES FLUX 900 is ideally suited to narrow gap welding due to the excellent slag detachability and smooth side-wall blending.
ES FLUX 180 is designed for use in the single-and multi-pass butt welding of mild and medium tensile steels where moderate impact strength is required.
ES FLUX 180 is of the calcium-silicate type with a very high current-carrying capacity, even at low welding speeds with both AC and DC.
ES FLUX 180 is excellent for the butt welding of materials from 10 to 30 mm thickness and is used in the shipbuilding industry, for example.
ES FLUX 180 is specially designed for use in combination with ES EL12 or ES EM12 in single- or multi-wire systems.
ES FLUX 171 is a basic agglomerated, slightly Si- and Mn-alloying fux for submerged arc welding, specially designed for fillet welding and for the single and multi-pass butt welding of mild, medium and high tensile steels. ES FLUX 171 is of the aluminate basic type and, for this slag system,
It has a very high current-carrying capacity on both AC and DC and very good operating characteristics.
ES FLUX 171 is ideally suited to narrow gap welding due to the excellent slag detachability and smooth side-wall blending.
ES EM12 is a copper-coated, semi-killed wire for the submerged arc and electro-slag wel ding of medium and high strength structural steels.
It can be combined with the following fluxes:
ES FLUX 171, ES FLUX 180
ES FLUX 181 and ES FLUX 900.
ES EM12 can be applied both for high-speed welding steel plate of 450-500 MPa tensile stren-gth steel (e.g. boiler, bridge, pressure vessel, and LPG cylinder).
ES FC 316LT is a fux-cored wire for the out-of-position welding of 316 and 316L type stainless steels where increased resistance to pitting corrosion is required.
This is particularly relevant when it comes to attack by chloride solutions and sulphuric acid.
The weld metal composition is such that the stabilised 321 and 347 stainless steels may also be welded.
ES MIG 5356 is the most widely used welding alloy and can be classified as a general-purpose type filler alloy.
ES MIG 5356 is typically cho- sen because of its relatively high shear strength.
The 5XXX alloy base material, welded with ES MIG 5356, with a weld pool chemistry greater than 3% Mg and service temperatures in excess of 65�°C, is susceptible to stress corrosion cracking.
ES MIG 5183 is designed to provide the highest possible strength in the as-welded condition of alloy AA 5083 and similar high-magnesium alloys.
The more common ES MIG 5356 typi- cally fails to meet the as-welded tensile require- ments of AA 5083.
The alloy is typically used in marine and structural applications where high strength, high fracture toughness for impact resistance and exposure to corrosive elements are important.
The alloy is not recommended for elevated temperature applications due to its susceptibility to stress corrosion cracking. The alloy is non-heat treatable.
ES MIG NiCr-3 is a nickel-based, corrosion and heat-resistant, 20% Cr, 3% Mo, 2.5% Nb electr-ode for the GMAW of high-alloyed steel, heat-resistant steel, corrosion-resistant steel, 9% Ni and similar steels with high notch toughness at low temperatures.
It is also suitable for joining dissimilar metals of the type mentioned above.
ES MIG NiCr-3 is usually welded with pure Ar as the shielding gas.
331 Titanium Wire Suppliers
Short on time? Let Titanium Wire sellers contact you.
