wireline winch consists ofelectric motora(or S195 diesel egine),clutch,transmission,drum,wirerope and brake etc,which has the advantages of simple structure,convenient and reliable operation,low noise,less mechanical wear,suitable for wide range of using.
Type: crown block Brand Name: Lake Model Number: all model Place of Origin: Shandong, China (Mainland) color: red Packaging Details: standard export package
Delivery Detail: with 20-35days
Hole Openers can be quoted with new/unused surplus or used Steel Tooth or TCI Cutters Hole Openers.
At some point it may be necessary to increase the size of a pre-drilled hole to a larger diameter or to drill large diameter holes. Hole opener bits are designed specifically for this purpose. Bits are custom manufactured in a wide range of styles to meet field requirements. A custom hole opener is an effective way of enlarging holes, hence the name "Hole Opener".
The Hole Opener Advantage
Straighter Holes - By drilling a smaller hole with a "pilot" bit, then attaching that said bit onto the bottom of the the hole opener. The hole opener will follow the path of the hole drilled by the smaller bit.
Larger Holes with Smaller Rigs - By drilling a hole in stages, larger holes can be drilled with smaller rigs. A smaller hole requires less power.
Replacing Cutters and Cutting Cost - On most Hole Opener designs, the cutters can be easily replaced. The cost to replace a cutter is a fraction of the cost to replace a large tricone rock bit.
Cost of Large Rock Bits - Larger diameter rock bits not only cost a lot, they can be difficult to find. A more economic solution is to use a hole opener that uses smaller tricone rock bit segments..
Flexability - Hole Openers can be fabricated in just about any size, and can be configured to drill through any formation.
Operational Considerations
Drilling Weight - The choice of drilling weight is determined based on the recommendations of the bit manufacturer and the number of cutters on the hole opener.
Number of Cutters - The number of cutters placed on a hole opener is governed by the following facts:
1.Maximum number which will fit around the perimeter.
2.The greater the number of cutters, the less the weight, which therefore reduces the penetration rate.
3.In softer formations, less weight is needed to penetrate.
4.The greater the number of cutters, the smoother the tool will run.
5.The greater the number of cutters, the greater the cost.
6.The greater the number of cutters, the longer the cutters will last
Rotary Speed - Maximum speed is determined by the manufacturer's recommendation and the calculation to account for the linear distance the cutter is moving per revolution.
Hole Cleaning - A frequently over looked point of hole opener operation is hole cleaning. The volume of cuttings to remove from a hole increase by a squared factor with an increase in hole diameter.
5828 Drilling Machines Tools Suppliers
Short on time? Let Drilling Machines Tools sellers contact you.
Applications:
â?¦ PDC drill bit is mainly used to drill Oil well, gas well, water well, etc.
â?¦ We design and produce specifie PDC bit with good performance for each soft, medium and hard formation.
â?¦ Clay stone/lignite/siltstone/sands: We design 3-5 blades with low density cutter placement,large slot. Low cost,high speed .
â?¦ Mudstone: We have experience to design suitalbe blades shape and cutter direction to get high drill speed and stalbe drill.
â?¦ Gravel/limestone/shale/clay stone/tuff: Round crown and reasonable cutter direction. Drill smoothly in good speed.
Model Number:417,517,617 ,437,537,637,117,217
Type: rock bit cutter
Material:Tungsten Carbide
Use: Well Drilling
Formation:soft to hard formation
Usage:Produce /replace hole opener cutters
Bearing type: journal bearing
Sealed type:metal sealing /Rubber seal
Teeth type: insert button or milled tooth,saw tooth
Name:Tci rock bit cutter
QY series portable fully hydraulic core drilling rig
1 Introduction to QY Series Portable Fully Hydraulic Core Drilling Rig
Fully hydraulic core exploration drilling rig adopts rope core drilling rig with full hydraulic power head drilling method, and the core drilled by the drilling tool is lifted out by the winch through the inner hole of the drill pipe to complete the geological drilling core work. It is mainly suitable for drilling solid ore deposits, and can also be used for engineering geology, shallow oil, natural gas, groundwater drilling, and engineering drilling such as tunnel ventilation, drainage and dike grouting.
2 Features of QY Series Portable Fully Hydraulic Core Drilling Rig
2.1 Modular design, light weight, easy to disassemble and carry.
2.2 The rig is fully hydraulic driven, and the hydraulic system adopts load sensitive control, with high working efficiency and high torque.
2.3 The power head rotation is driven by axial piston pump and inclined shaft piston motor, and the mechanical two gears plus step less speed regulation, advanced structure.
2.4 Equipped with a lateral translation mechanism for the power head, the mast is raised and lowered by a cylinder and can slide as a whole, and can drill holes within the range of 45-90�°.
2.5 Hydraulic gripper to achieve clamping drill pipe, with drill pipe disassembly.
2.6 Hydraulic motor driven hoist, can be flexible lifting drilling tools or auxiliary tools.
3ã??Parameters of QY Series Portable Fully Hydraulic Core Drilling Rig
Drilling rig model QY-600 QY-800 QY-1000
Drilling capacity BTW 600m 800m 1000m
NTW 400m 600m 800m
HTW 200m 400m 400mm
PQ / / /
Hydraulic system Rated pressure 20mpa 20mpa 20mpa
cooling mode water cooling water cooling water cooling
Engine Engine type Yunnei Yunnei Yunnei
Rated power 55kW*2 58kW*3 55kW*3
Power head Maximum torque 1200N.m 1600N.m 500-1460N.m
Maximum rotate speed 1100rpm 1100rpm 1300rpm
Feeding stroke 1800mm 1800mm 1800mm
Lifting force 100kN 120kN 160kN
Propulsion force 75kN 85kN 80kN
Wire-line coring winch Rope capacity 600m 800m 1000m
Lifting force 15kN 15kN 24kN
Lifting speed 110m/min 110m/min 110m/min
Mast parameters Full height 5.8m 5.8m 5.8m
Drilling angle 45-90�° 45-90�° 45-90�°
Transport size L*W*H 3.8*1.5*1.3m 4.8*1.5*1.3m 5.6*2.0*1.3m
Whole machine weight 1.6T 2T 2.3T
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
QY series portable fully hydraulic core drilling rig
1 Introduction to QY Series Portable Fully Hydraulic Core Drilling Rig
Fully hydraulic core exploration drilling rig adopts rope core drilling rig with full hydraulic power head drilling method, and the core drilled by the drilling tool is lifted out by the winch through the inner hole of the drill pipe to complete the geological drilling core work. It is mainly suitable for drilling solid ore deposits, and can also be used for engineering geology, shallow oil, natural gas, groundwater drilling, and engineering drilling such as tunnel ventilation, drainage and dike grouting.
2Features of QY Series Portable Fully Hydraulic Core Drilling Rig
2.1 Modular design, light weight, easy to disassemble and carry.
2.2 The rig is fully hydraulic driven, and the hydraulic system adopts load sensitive control, with high working efficiency and high torque.
2.3 The power head rotation is driven by axial piston pump and inclined shaft piston motor, and the mechanical two gears plus step less speed regulation, advanced structure.
2.4 Equipped with a lateral translation mechanism for the power head, the mast is raised and lowered by a cylinder and can slide as a whole, and can drill holes within the range of 45-90�°.
2.5 Hydraulic gripper to achieve clamping drill pipe, with drill pipe disassembly.
2.6 Hydraulic motor driven hoist, can be flexible lifting drilling tools or auxiliary tools.
3. Parameters of QY Series Portable Fully Hydraulic Core Drilling Rig
Drilling rig model QY-600 QY-800 QY-1000
Drilling capacity BTW 600m 800m 1000m
NTW 400m 600m 800m
HTW 200m 400m 400mm
PQ / / /
Hydraulic system Rated pressure 20mpa 20mpa 20mpa
cooling mode water cooling water cooling water cooling
Engine Engine type Yunnei Yunnei Yunnei
Rated power 55kW*2 58kW*3 55kW*3
Power head Maximum torque 1200N.m 1600N.m 500-1460N.m
Maximum rotate speed 1100rpm 1100rpm 1300rpm
Feeding stroke 1800mm 1800mm 1800mm
Lifting force 100kN 120kN 160kN
Propulsion force 75kN 85kN 80kN
Wire-line coring winch Rope capacity 600m 800m 1000m
Lifting force 15kN 15kN 24kN
Lifting speed 110m/min 110m/min 110m/min
Mast parameters Full height 5.8m 5.8m 5.8m
Drilling angle 45-90 45-90 45-90
Transport size L*W*H 3.8*1.5*1.3m 4.8*1.5*1.3m 5.6*2.0*1.3m
Whole machine weight 1.6T 2T 2.3T
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
QY series portable fully hydraulic core drilling rig
1 Introduction to QY Series Portable Fully Hydraulic Core Drilling Rig
Fully hydraulic core exploration drilling rig adopts rope core drilling rig with full hydraulic power head drilling method, and the core drilled by the drilling tool is lifted out by the winch through the inner hole of the drill pipe to complete the geological drilling core work. It is mainly suitable for drilling solid ore deposits, and can also be used for engineering geology, shallow oil, natural gas, groundwater drilling, and engineering drilling such as tunnel ventilation, drainage and dike grouting.
2 Features of QY Series Portable Fully Hydraulic Core Drilling Rig
2.1 Modular design, light weight, easy to disassemble and carry.
2.2 The rig is fully hydraulic driven, and the hydraulic system adopts load sensitive control, with high working efficiency and high torque.
2.3 The power head rotation is driven by axial piston pump and inclined shaft piston motor, and the mechanical two gears plus step less speed regulation, advanced structure.
2.4 Equipped with a lateral translation mechanism for the power head, the mast is raised and lowered by a cylinder and can slide as a whole, and can drill holes within the range of 45-90.
2.5 Hydraulic gripper to achieve clamping drill pipe, with drill pipe disassembly.
2.6 Hydraulic motor driven hoist, can be flexible lifting drilling tools or auxiliary tools.
3 .Parameters of QY Series Portable Fully Hydraulic Core Drilling Rig
Drilling rig model QY-600 QY-800 QY-1000
Drilling capacity BTW 600m 800m 1000m
NTW 400m 600m 800m
HTW 200m 400m 400mm
PQ / / /
Hydraulic system Rated pressure 20mpa 20mpa 20mpa
cooling mode water cooling water cooling water cooling
Engine Engine type Yunnei Yunnei Yunnei
Rated power 55kW*2 58kW*3 55kW*3
Power head Maximum torque 1200N.m 1600N.m 500-1460N.m
Maximum rotate speed 1100rpm 1100rpm 1300rpm
Feeding stroke 1800mm 1800mm 1800mm
Lifting force 100kN 120kN 160kN
Propulsion force 75kN 85kN 80kN
Wire-line coring winch Rope capacity 600m 800m 1000m
Lifting force 15kN 15kN 24kN
Lifting speed 110m/min 110m/min 110m/min
Mast parameters Full height 5.8m 5.8m 5.8m
Drilling angle 45-90 45-90 45-90
Transport size L*W*H 3.8*1.5*1.3m 4.8*1.5*1.3m 5.6*2.0*1.3m
Whole machine weight 1.6T 2T 2.3T
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
QY series portable fully hydraulic core drilling rig
1 Introduction to QY Series Portable Fully Hydraulic Core Drilling Rig
Fully hydraulic core exploration drilling rig adopts rope core drilling rig with full hydraulic power head drilling method, and the core drilled by the drilling tool is lifted out by the winch through the inner hole of the drill pipe to complete the geological drilling core work. It is mainly suitable for drilling solid ore deposits, and can also be used for engineering geology, shallow oil, natural gas, groundwater drilling, and engineering drilling such as tunnel ventilation, drainage and dike grouting.
2ã??Features of QY Series Portable Fully Hydraulic Core Drilling Rig
2.1 Modular design, light weight, easy to disassemble and carry.
2.2 The rig is fully hydraulic driven, and the hydraulic system adopts load sensitive control, with high working efficiency and high torque.
2.3 The power head rotation is driven by axial piston pump and inclined shaft piston motor, and the mechanical two gears plus step less speed regulation, advanced structure.
2.4 Equipped with a lateral translation mechanism for the power head, the mast is raised and lowered by a cylinder and can slide as a whole, and can drill holes within the range of 45-90�°.
2.5 Hydraulic gripper to achieve clamping drill pipe, with drill pipe disassembly.
2.6 Hydraulic motor driven hoist, can be flexible lifting drilling tools or auxiliary tools.
3ã??Parameters of QY Series Portable Fully Hydraulic Core Drilling Rig
Drilling rig model QY-600 QY-800 QY-1000
Drilling capacity BTW 600m 800m 1000m
NTW 400m 600m 800m
HTW 200m 400m 400mm
PQ / / /
Hydraulic system Rated pressure 20mpa 20mpa 20mpa
cooling mode water cooling water cooling water cooling
Engine Engine type Yunnei Yunnei Yunnei
Rated power 55kW*2 58kW*3 55kW*3
Power head Maximum torque 1200N.m 1600N.m 500-1460N.m
Maximum rotate speed 1100rpm 1100rpm 1300rpm
Feeding stroke 1800mm 1800mm 1800mm
Lifting force 100kN 120kN 160kN
Propulsion force 75kN 85kN 80kN
Wire-line coring winch Rope capacity 600m 800m 1000m
Lifting force 15kN 15kN 24kN
Lifting speed 110m/min 110m/min 110m/min
Mast parameters Full height 5.8m 5.8m 5.8m
Drilling angle 45-90�° 45-90�° 45-90�°
Transport size L*W*H 3.8*1.5*1.3m 4.8*1.5*1.3m 5.6*2.0*1.3m
Whole machine weight 1.6T 2T 2.3T
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
JFD Series Crawler Reverse Circulation Water Well Drilling Rig
1. Introduction of JFD Series Crawler Reverse Circulation Water Well Drilling Rig
The rotary water well drilling rig with reverse circulation well washing medium is referred to as reverse circulation drilling rig. Its core lies in the unique "reverse circulation" working mode. The drilling fluid naturally flows into the annular gap between the drill pipe and the well wall directly to the bottom of the well, and then carries the cut drill cuttings back to the wellhead through the inner cavity of the drill pipe, and is discharged to the water supply pool through the faucet and the slag discharge pipe, and is recycled after sedimentation and clarification. This "outside down and inside up" circulation method is particularly good at handling large-diameter drilling operations in complex formations such as pebbles and gravel, and has achieved efficient slag discharge capabilities far exceeding traditional drilling rigs. It is mainly used in the fields of water well drilling and engineering bored pile drilling.
2. Features of JFD Series Crawler Reverse Circulation Water Well Drilling Rig
2.1 The mud pump has strong suction, high rising flow rate, and strong pipeline slag discharge capacity. It can continuously and quickly discharge the cut drilling slag or pebbles out of the hole, reducing the number of repeated cutting or grinding and significantly improving the construction speed.
2.2 The power head has large rotation torque, which is more suitable for large-diameter drilling operations.
2.3 Equipped with crawler walking chassis, no need for manual movement, making it more convenient to move the machine.
2.4 Equipped with hydraulic legs to level the drilling rig and ensure the stability of the machine body.
2.5 There is ample driving space on the crawler chassis, making operation more convenient.
2.6 The layout of the operating handle and distribution box is compact and reasonable, which is convenient for centralized control.
2.7 The slide adopts heavy-duty structural design, and the key parts are shock-proof and wear-resistant, with a long service life and low failure rate.
3. Parameters of JFD Series Crawler Reverse Circulation Water Well Drilling Rig
Drilling rig specifications JFD-5 JFD-6 JFD-6S JFD-7S
Drilling diameter 300-1000mm 500-1500mm 500-1800mm 500-2500mm
Drilling depth 40-80m 20-100m 30-200m 30-200m
Drill pipe specifications 140*2000mm 168*2000mm 168*2000mm 194*2000mm
Generator power 50kW 50kW 75kW 100kW
Hydraulic pump motor power 7.5kW 15kW 11kW 22kW
Mud pump motor power 15kW 22kW 30kW 37kW
Rotary motor power 7.5kW 11kW 5.5kW*2 7.5kW*2
Rotation torque 18kN 20kN 26kN 30kN
Rotation speed 13rpm 13rpm 13rpm 10rpm
Vacuum pump motor power 7.5kW 7.5kW 7.5kW 11kW
Winch motor power 1kW 1kW 1kW 1kW
1. Introduction of SPJ Series Grinding Disc Water Well Drilling Rig
The SPJ series grinding disc drilling rig is a multifunctional large-diameter drilling rig. Its core disc-shaped power head drives the drill to rotate and cut the strata. It has the advantages of good hole quality, high efficiency, and strong adaptability. It can perform large-diameter and deep-hole drilling operations in soil, sand, gravel, and soft rock layers. It is widely used in water well drilling and pile foundation construction of various construction projects, bridge projects, municipal projects, etc. At the same time, the grinding disc drilling rig can also be customized into trailer-type, vehicle-mounted, or crawler-type according to customer needs.â??
2. Features of SPJ Series Grinding Disc Water Well Drilling Rig
2.1 The grinding disc drilling rig is equipped with a diesel generator set and a distribution box. In areas with electricity, it can also be directly connected to the power supply through the distribution box to work, and the power selection is more flexible.
2.2 The drilling rig adopts modular design, which is convenient for assembly and disassembly, and easy for transfer and transportation.
2.3 The winch is configured to realize the lifting of drilling tools, lowering of well pipes, and vertical placement of drilling towers, making the construction convenient and efficient.
2.4 The drilling tower adopts heavy-duty structural design, with key parts resistant to shock and wear, strong structural stability and outstanding anti-overturning performance.
2.5 The drilling rig is simple and easy to learn, and novices can quickly get started, reducing dependence on manual labor.
3.Parameters of SPJ Series Grinding Disc Water Well Drilling Rig
Drilling rig model SPJ-400 SPJ-600 SPJ-1000
Drilling diameter 500mm-1800mm 500mm-2500mm 500mm-2500mm
Drilling depth 50m-400m 50m-600m 50m-1000m
Active drill pipe 108*108*12mm 108*108*12mm 133*133*12mm
Drill pipe 89mm 89mm 89mm/114mm
Main winch lifting capacity 32T 60T 60T
Main winch wire rope diameter 18mm 20-21.5mm 20-21.5mm
Main winch wire rope capacity 150m 240m 280m
Auxiliary winch lifting capacity 15T 32T 32T
Auxiliary winch wire rope diameter 14mm 18mm 18mm
Auxiliary winch wire rope capacity 150m 150m 280
Diameter of turntable hole 500mm 605mm 670mm
Turntable speed (forward, reverse) 40-70-128r/min 50-70-128r/min 36-60-90-130r/min
Drilling tower Type A Type A Type A
Vertical height of drilling tower 13m 13m 18m
Weight of the whole set (without drill rod) 9T 11T 15T
Dimensions 6000*2200*13000mm 6000*4000*13500 6000*4500*18000
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
JFC-5 Tractor Mounted Reverse Circulation Water Well Drilling Rig
1.Introduction of JFC-5 Tractor Mounted Reverse Circulation Water Well Drilling Rig
The rotary water well drilling rig with reverse circulation well washing medium is referred to as reverse circulation drilling rig. Its core lies in the unique "reverse circulation" working mode. The drilling fluid naturally flows into the annular gap between the drill pipe and the well wall directly to the bottom of the well, and then carries the cut drill cuttings back to the wellhead through the inner cavity of the drill pipe, and is discharged to the water supply pool through the faucet and the slag discharge pipe, and is recycled after sedimentation and clarification. This "outside down and inside up" circulation method is particularly good at handling large-diameter drilling operations in complex formations such as pebbles and gravel, and has achieved efficient slag discharge capabilities far exceeding traditional drilling rigs. It is mainly used in the fields of water well drilling and engineering bored pile drilling.â??
2. Features of JFC-5 Tractor Mounted Reverse Circulation Water Well Drilling Rig
2.1 With the tractor as the carrier, the mechanical structure technology is mature and the performance is stable.
2.2 The tractor chassis has all-terrain off-road capabilities and can be easily moved to other locations in complex terrains such as muddy fields, rugged hillsides, and narrow country roads.
2.3 The mud pump has strong suction, high rising flow rate, and strong pipeline slag discharge capacity. It can continuously and quickly discharge the cut drilling slag or pebbles out of the hole, reducing the number of repeated cutting or grinding and significantly improving the construction speed.
2.4 Equipped with hydraulic outriggers to level the drilling rig and ensure the stability of the machine body.
2.5 The well drilling rig is equipped with a generator in front, which is easy to switch between diesel and electricity.
2.6 The operating handle and distribution box are compactly and reasonably arranged for easy operation.
2.7 Equipped with a 5-speed gearbox, it can meet the differentiated speed requirements of different formations.
3. Parameters of JFC-5 Tractor Mounted Reverse Circulation Water Well Drilling Rig
Drilling diameter 300-1000mm
Drilling depth 0-60m
Drill pipe specifications 140*2000mm
Drilling speed 20-126r/min(Five-speed shift)
Mud pump motor 15kW
Rotary motor 11kW
Vacuum pump motor 4kW
Hydraulic oil pump motor 4kW
Tractor chassis 50HP
Drilling rig weight 4.7T
Shipping dimensions 5800*2100*2700mm
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
HJD Horizontal Mountain Spring Well Water Drilling Rig
1 Introduction of HJD Horizontal Mountain Spring Water Well Drilling Rig
HJD horizontal spring water well drilling rig adopts modular design, which is composed of main machine, slide way, distribution board, water gas bottle, etc., with reasonable layout and compact structure. In order to further facilitate mobile handling, the main machine can continue to be disassembled into rotary part, propulsion part and main machine base, and the slide way can continue to be disassembled into guide rail, wire rope tensioner and drilling tool support frame. The main machine of the drilling rig adopts the principle of water and gas combination of pneumatic drilling and wet slag removal, which can be used in conjunction with the long-stroke slide to realize the horizontal drilling of mountains. The drilling rig has been widely used in horizontal drilling and mountain horizontal drilling.
2 Features of HJD Horizontal Mountain Spring Water Well Drilling Rig
2.1 The drilling rig adopts the working principle of water and air combination, with high efficiency, fast footage and less dust.
2.2 Long stroke slide way shall be configured and long drill pipe shall be selected to reduce the number of drill pipe switching.
2.3 The drilling rig adopts modular design, which can be easily disassembled and assembled, and is convenient for transportation and handling.
2.4 In addition to forward rotation, the main machine is equipped with inching forward rotation and inching reverse rotation for easy loading and unloading of drill pipe.
2.5 The power distribution panel of the drilling rig is equipped with a wireless remote controller, which can realize remote operation of the host.
3 Parameters of HJD Horizontal Mountain Spring Water Well Drilling Rig
Model HJD
Drilling diameter 65-70-76-80mm
Drill pipe specifications42*4000
Voltage 380V
Power Rotary motor 4kW
Propulsion motor 2.2kW
Weight Turning part 90kg
Promotion Department 69kg
Host base 80kg
Guide 38kg/Strip
Drill tool support 19kg
Water bottle 20kg
Distribution box 10kg
Assembly size 5660*840*970mm
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
1 Introduction of SJCY-D Crawler Diesel Hydraulic Drilling Rig
SJCY-D crawler diesel hydraulic water well drilling rig is a hydraulic drilling rig developed and widely promoted by Shandong Master Group. It is suitable for drilling in soil layer, quicksand layer and a small amount of rock and soil layer. It is mainly used for drilling civil draft wells, ground source heat pump air conditioning wells, engineering dewatering wells, drought-resistant wells, industrial wells, etc.
2 Features of SJCY-D Crawler Diesel Hydraulic Drilling Rig
2.1 The diesel engine is equipped with electric starting, which is convenient to start and reduces the labor intensity of the operator.
2.2 The drilling rig adopts hydraulic working principle and is equipped with radiator, so the drilling rig can work continuously and efficiently.
2.3 Equipped with high-power hydraulic motor, the power head can rotate forward and backward.
2.4 The drill frame is equipped with hydraulic oil cylinder, and the oil pressure can be raised and lowered through the operating handle.
2.5 The drilling rig has its own water pump, which has reasonable structure, compact layout and good slag removal effect.
2.6 Equipped with rubber steel wire tracks, it is easy to move, and it will not hurt the road surface when walking on urban roads.
3 Parameters of SJCY-D Crawler Diesel Hydraulic Drilling Rig
Model SJCY-D
Machine power Single cylinder diesel engine/22 HP
Chassis Rubber crawler hydraulic walking chassis
Vehicle weight 950kg
Overall machine size 2000*1100*2100mm
Power head BM5-200 Hydraulic Motor
Pressurized system Hydraulic cylinder booster
Outrigger Four screw legs
Drill pipe specifications 50*1500mm
Drilling diameter 80-300mm
Drilling depth 0-120m
Slide travel 2400mm
Lift height 2600mm
One-time advancement length 1500mm
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
HJD Horizontal Mountain Spring Well Water Drilling Rig
1 Introduction of HJD Horizontal Mountain Spring Water Well Drilling Rig
HJD horizontal spring water well drilling rig adopts modular design, which is composed of main machine, slide way, distribution board, water gas bottle, etc., with reasonable layout and compact structure. In order to further facilitate mobile handling, the main machine can continue to be disassembled into rotary part, propulsion part and main machine base, and the slide way can continue to be disassembled into guide rail, wire rope tensioner and drilling tool support frame. The main machine of the drilling rig adopts the principle of water and gas combination of pneumatic drilling and wet slag removal, which can be used in conjunction with the long-stroke slide to realize the horizontal drilling of mountains. The drilling rig has been widely used in horizontal drilling and mountain horizontal drilling.
SJCY Traction Diesel Hydraulic Water Well Drilling Rig
1 Introduction of SJCY Traction Diesel Hydraulic Water Well Drilling Rig
SJCY towable diesel hydraulic water well drilling rig is a hydraulic drilling rig developed and widely promoted by HUAXIAMASTER GROUP. It is suitable for drilling in soil layer, quicksand layer and a small amount of rock and soil layer. It is mainly used for drilling civil draft wells, ground source heat pump air conditioning wells, engineering dewatering wells, drought-resistant wells, industrial wells, etc.
2 Features of SJCY Traction Diesel Hydraulic Water Well Drilling Rig
2.1 The diesel engine is equipped with electric starting, which is convenient to start and reduces the labor intensity of the operator.
2.2 The drilling rig adopts hydraulic working principle and is equipped with radiator, so the drilling rig can work continuously and efficiently.
2.3 Equipped with high-power hydraulic motor, the power head can rotate forward and backward.
2.4 The drill frame is equipped with hydraulic oil cylinder, and the oil pressure can be raised and lowered through the operating handle.
2.5 The drilling rig has its own water pump, which has reasonable structure, compact layout and good slag removal effect.
3 Parameters of SJCY Traction Diesel Hydraulic Water Well Drilling Rig
Drilling rig specifications SJCY
Machine power Single cylinder diesel engine/22 HP
Vehicle weight 560KG
Overall machine size 1900*980*1800mm
Power head BM5-200 Hydraulic Motor
Pressurized system Hydraulic cylinder booster
Outrigger four screw rods
Drill pipe specifications 50*1500mm
Drilling diameter 80-300mm
Drilling depth 0-120m
Slide travel 2400mm
Lift height 2600mm
One-time advancement length 1500mm
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
CJC Series Truck-mounted Pneumatic Water Well Drilling Rig
1 Introduction of CJC Series Truck-mounted Pneumatic Water Well Drilling Rig
CJC truck mounted pneumatic water well drilling rig is a kind of pneumatic water well drilling rig jointly developed by HUAXIAMASTER GROUP and Jining Master Machinery Research Institute. It is mainly used for drilling in Hilly and mountainous areas with many rocks. It has the advantages of large diameter, deep drilling, fast footage, flexible movement and high efficiency. It has been widely used in industrial and civil drilling, geothermal drilling and environmental monitoring drilling Well and other occasions.
2 Features Of CJC Series Truck-mounted Pneumatic Water Well Drilling Rig
2.1 Using the principle of pneumatic impact, the drilling footage is fast and the drilling efficiency is high.
2.2 It adopts truck chassis, reasonable and compact layout and easy operation.
2.3 Equipped with hydraulic outrigger, it is used for leveling the drilling rig and maintaining the stability of the fuselage.
2.4 The main engine is equipped with high-power diesel engine, which has strong power and can meet the needs of work
2.5 Equipped with hydraulic take-off and landing composite boom to save space and provide strong lifting force for deep hole operation.
2.6 The drilling rig is equipped with hydraulic feeding system, dual hydraulic motor power head, chain drive and hydraulic cylinder propulsion, with large torque and high drilling efficiency.
2.7 The configuration of hydraulic wrench, can quickly disassemble the drill pipe, saving time and effort.
2.8 The operation handle is centralized, the layout is reasonable, safe and feasible
2.9 Excellent workmanship, durable and low maintenance cost.
3 Parameters of CJC Series Truck-mounted Pneumatic Water Well Drilling Rig
Model CJC-300 CJC-350 CJC-450 CJC-500 CJC-600 CJC-700
Borehole diameter 140-325mm 140-325mm 140-350mm 140-350mm 140-350mm 140-400mm
Drilling depth 300m 350m 450m 500m 600m 700m
Drill pipe diameter 76/89/102mm 89/102mm 89/102/108mm 102/108/114mm 102/108/114mm 102/108/114mm
Drill pipe length 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m
One time propulsion length 6600mm 6600mm 6600mm 6600mm 6600mm 6600mm
Main engine power 85kW 91kW 103kW 118kW 132kW 153kW
Propulsion 8T 8T 18T 18T 23T 23T
Lifting power 18T 22T 25T 26T 30T 30T
Working pressure 1.7-3.0Mpa 1.7-3.4Mpa 1.7-3.5Mpa 1.7-3.5Mpa 1.7-3.5Mpa 1.7-3.5Mpa
Air consumption 17-36m³/min 17-36m³/min 17-36m³/min 17-42m³/min 17-42m³/min 17-42m³/min
Walking speed 2.5km/h 2.5km/h 2.5km/h 2.5km/h 2.5km/h 2.5km/h
CJDX Series Crawler Pneumatic Water Well Drilling Rig
1 Introduction Of CJDX Series Crawler Pneumatic Water Well Drilling Rig
CJDX series crawler pneumatic water well drilling rig is a kind of pneumatic water well drill jointly developed by HUAXIAMASTER GROUP and Jining Master Research Institute. It is mainly used for drilling operations in hilly and mountainous areas where there are many rocks. It has the advantages of large drilling diameter, deep drilling, fast penetration, flexible movement and high efficiency. It has been widely used in industrial drilling, geothermal drilling, environmental monitoring drilling and other occasions.
2 Features Of CJDX Series Crawler Pneumatic Water Well Drilling Rig
2.1 Using the principle of pneumatic impact, the drilling footage is fast and the drilling efficiency is high.
2.2 Equipped with rubber steel wire tracks, it is easy to move, and it will not hurt the road surface when walking on urban roads.
2.3 Equipped with hydraulic high outrigger, it is easy to load and unload the truck, save the hoisting cost, and can be used for leveling the drilling rig to maintain the stability of the fuselage
2.4 Equipped with high-power diesel engine, strong power, to meet the needs of work.
2.5 Equipped with hydraulic take-off and landing composite boom to save space and provide strong lifting force for deep hole operation.
2.6 The drilling rig is equipped with hydraulic feeding system, dual hydraulic motor power head, chain drive and hydraulic cylinder propulsion, with large torque and high drilling efficiency.
2.7 Equipped with a quick stripper, the drill pipe can be disassembled quickly, saving time and labor.
2.8 The operation handle is centralized, reasonable in layout, safe and feasible.
2.9 Excellent workmanship, durable and low maintenance cost.
3 Parameters of CJDX Series Crawler Pneumatic Water Well Drilling Rig
Drilling rig specifications CJDX-160 CJDX-200 CJDX-230S
Borehole diameter 130-203 140-325 140-325
Drilling depth 160m 200m 230m
Drill pipe diameter 76 76-89 76-89
Drill pipe length 2m 1.5m-2.0m-3.0m 1.5m-2.0m-3.0m
`One time propulsion length 2400mm 3300mm 3300mm
Main engine power 63kW 55kW 65kW
Propulsion 7T 8T 5T
Lifting power 15T 16T 15T
Working pressure 1.2-3.0Mpa 1.7-2.5Mpa 1.7-2.5Mpa
Air consumption 10-25m³/min 17-31m³/min 17-31m³/min
Walking speed 2.5km/h 2.5km/h 2.5km/h
Climbing ability 30Max 30Max 30Max
Rotation speed 65-100rpm 40-160rpm 70-140rpm
Slewing torque 4500N.m 5000N.m 6000N.m
Dimensions 2540*1200*1880mm 3850*1800*2450mm 3250*1750*2180mm
Total weight 2.8T 4T 5.5T
Note: Products are constantly being improved. Any changes will not be notified separately. Please refer to the actual product.
CJD Series Crawler Pneumatic Water Well Drilling Rig
1 Introduction of CJD Series Crawler Pneumatic Water Well Drilling Rig
CJD series crawler pneumatic water well drilling rig is a kind of pneumatic water well drill jointly developed by HUAXIAMASTER GROUP and Jining Master Research Institute. It is mainly used for drilling operations in hilly and mountainous areas where there are many rocks. It has the advantages of large drilling diameter, deep drilling, fast penetration, flexible movement and high efficiency. It has been widely used in industrial drilling, geothermal drilling, environmental monitoring drilling and other occasions.â??
2 Features of CJD Series Crawler Pneumatic Water Well Drilling Rig
2.1 Using the principle of pneumatic impact, the drilling footage is fast and the drilling efficiency is high.
2.2 Equipped with steel crawler chassis, strong cross-country performance, easy to deal with a variety of complex working sites
2.3 Equipped with hydraulic high outrigger, it is easy to load and unload the truck, save the hoisting cost, and can be used for leveling the drilling rig to maintain the stability of the fuselage
2.4 Equipped with high-power diesel engine, strong power, to meet the needs of work.
2.5 Equipped with hydraulic take-off and landing composite boom to save space and provide strong lifting force for deep hole operation.
2.6 The drilling rig is equipped with hydraulic feeding system, dual hydraulic motor power head, chain drive and hydraulic cylinder propulsion, with large torque and high drilling efficiency.
2.7 Equipped with a quick stripper, the drill pipe can be disassembled quickly, saving time and labor.
2.8 The operation handle is centralized, reasonable in layout, safe and feasible.
2.9 Excellent workmanship, durable and low maintenance cost.
3 Parameters of CJD Series Crawler Pneumatic Water Well Drilling Rig
Model CJD-260 CJD-300 CJD-350 CJD-450 CJD-500 CJD-600 CJD-700
Borehole diameter 140-325mm 140-325mm 140-325mm 140-350mm 140-350mm 140-350mm 140-400mm
Drilling depth 260m 300m 350m 450m 500m 600m 700m
Drill pipe diameter 76/89/102mm 76/89/102mm 89/102mm 89/102/108mm 102/108/114mm 102/108/114mm 102/108/114mm
Drill pipe length 1.5/2.0/3.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m 1.5/2.0/3.0/6.0m
One time propulsion length 3300mm 6600mm 6600mm 6600mm 6600mm 6600mm 6600mm
Main engine power 76kW 85kW 91kW 103kW 118kW 132kW 153kW
Propulsion 8T 8T 8T 18T 18T 23T 23T
Lifting power 16T 18T 22T 25T 26T 30T 30T
Working pressure 1.7-2.5Mpa 1.7-3.0Mpa 1.7-3.4Mpa 1.7-3.5Mpa 1.7-3.5Mpa 1.7-3.5Mpa 1.7-3.5Mpa
Air consumption 17-31m³/min 17-36m³/min 17-36m³/min 17-36m³/min 17-42m³/min 17-42m³/min 17-42m³/min
Walking speed 2.5km/h 2.5km/h 2.5km/h 2.5km/h 2.5km/h 2.5km/h 2.5km/h
Climbing ability 30Max 30Max 30Max 30Max 30Max 30Max 30Max
Rotation speed 40-160rpm 40-70rpm 66-135rpm 50-135rpm 40-130rpm 45-140rpm 45-140rpm
5828 Drilling Machines Tools Suppliers
Short on time? Let Drilling Machines Tools sellers contact you.
