We are manufacturer of 95% Spill Track Casting Powder forms a good lubricating film on the surface of mould not allowing solidifying metal adhesion to the mould. Casting Powder provides easy and fast solidification of metal by providing high rate heat removal from metal. Casting Powder gives very good performance at elevated temperatures with the aid of its well selected additives. Casting Powder increases the quality of metal surface. Casting Powder is cheaper than Rapeseed/Casting Oil.
We are enagaged in offering 90% Heat Insulation Radex Powder to our clients.
Uses:
We are also engaged in offering our quality conscious industrial customers quality Expandable Heat Insulation Compounds. These are basically used in steel industries on Ladle or Tundish and help in producing tailor-made refractory that are at par with international standards. Suiting specific applications of Industries like Steel, Glass, Cement, Coke Oven, Re-rolling Mills, Sponge Iron and others, we can offer these in different specifications to choose from.
We are also engaged in successfully offering our industrial customers 79% Powder Heat Insulation Compound Powder that is of high quality and basically finds usage in Steel Plants. Having a free flow, it is used in tundish or ladle and helps in preventing heat loss. Further, its usage also ensures smooth casting operation as well as helps in also enhancing the service life of ladle.
We are also engaged in successfully offering our 74% Powder Heat Insulation Compound Powder that is of high quality and basically finds usage in Steel Plants. Having a free flow, it is used in tundish or ladle and helps in preventing heat loss. Further, its usage also ensures smooth casting operation as well as helps in also enhancing the service life of ladle.
High performance concrete
High strength, low permeability concrete
Industrial flooring
Water tanks and sumps
Chemical storage tanks
Basements and sewerage pipelines
Refractory mixes etc.
Petroleum Refineries
Tunnels
Compatible with most of the admixtures to accelerate / retard the setting time
Supports all portions of structures
Fill up the voids in concrete structure, control or prevent the structure from leakage or weak structures to strengthen
Non-toxic, Non-Hazards.
Eco friendly & Cost Effective.
Method of Uses:
â?¢ The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
â?¢ MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes.
â?¢ Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
â?¢ Packaging: G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
â?¢ Storage: G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
â?¢ Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25�°C, protected from heat, frost and direct sunlight.
â?¢ Safety Information: Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high con-centrations of dust may cause irritation.
â?¢ It is recommended that suitable protective clothing, gloves and eye/face protection is worn.
â?¢ In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
Method of Uses:
â?¢ The substrate must be cleaned down to load bearing grain structure. Before grouting the substrate is to be rinsed until it is saturated excess water will be removed.
â?¢ MF-8 should be mixed with a slowly rotating mixer to avoid air pockets. First add 2/3 of the totally required water. After mixing for a short time add the balance of water. It should be mixed for approx. 6 minutes.
â?¢ Plastic consistency for vertical and overhead surfaces: 4 litres of water per 20 kg bag Liquid consistency for injection as per requirement.
â?¢ Packaging: G-GROUT MF-8 is available in Bulk Jumbo bags with plastic inner liner. The product is also available in 25 kg plastic line bags.
â?¢ Storage: G-GROUT MF-8 when stored correctly has an indefinite shelf life. Like cement, it must be protected from contamination and moisture. The product can be stored in bulk in a clean, dry storage silo.
â?¢ Shelf life is at least 12 month in original packaging when stored in dry conditions between 15-25�°C, protected from heat, frost and direct sunlight.
â?¢ Safety Information: Extensive testing has shown G-GROUT MF-8 to be non-toxic and environmentally benign. No known significant health risks are associated with G-GROUT MF-8 but high concentrations of dust may cause irritation.
â?¢ It is recommended that suitable protective clothing, gloves and eye/face protection is worn.
â?¢ In case of contact with eyes, rinse immediately with plenty of clean water and seek medical advice.
Marcolex1 Moulding Casting Gel Powder for 3D Casting, a user-friendly and eco-friendly solution for various DIY projects, including 3D casting. This powder is designed for quick setting and easy demolding, making it suitable for both beginners and experienced crafters.
After the addition of DA Fusion a liquid slag is quickly formed which is in direct contact with the steel surface as it rises up the ingot. This liquid flux dissolves the nonmetallic inclusions which rise to the surface, whilst providing a protective layer between the steel and the ingot mould. In addition a powdered layer is maintained on the surface which protects the steel from the atmosphere and prevents oxidation and temperature loss.
After the addition of DA Fusion a liquid slag is quickly formed which is in direct contact with the steel surface as it rises up the ingot. This liquid flux dissolves the non-metallic inclusions which rise to the surface, whilst providing a protective layer between the steel and the ingot mould. In addition a powdered layer is maintained on the surface which protects the steel from the atmosphere and prevents oxidation and temperature loss.
We are also engaged in successfully offering our 74% Powder Heat Insulation Compound Powder that is of high quality and basically finds usage in Steel Plants. Having a free flow, it is used in tundish or ladle and helps in preventing heat loss. Further, its usage also ensures smooth casting operation as well as helps in also enhancing the service life of ladle.
50588 Mining Metallurgy Suppliers
Short on time? Let Mining Metallurgy sellers contact you.
