Plastic distribution box,color white,surface-mounted box.
Details:
1)Outdoor waterproof distribution box, waterproof, sunscreen, dustproof.
2)The inside of the box is equipped with guide rails and grounding terminals.
3)There are reserved holes on the side of the box for easy cable entry and exit.
4)The transparent cover can see the components inside the enclosure, whether it is safe.
5)There is a waterproof sealing ring in the box, so that the water has nowhere to drill.
6)Wide range of applications. Housing, factories, workshops, airports, cruise ships.
Metal Clasp Waterproof box,Plastic Electrical Boxes,waterproof enclosures,surface-mounted enclosure,Plastic Electronic Boxes.
Plastic Electrical Boxes,light gray,
lock type: Metal Clasp,surface-mounted enclosure.
Details:
1)Reinforced sealing ring,the reinforced seal ring is elastic, not easy to break, and will not be deformed or yellowed after long-term use.
2)Buckle design, buckle hinge design allows you to easily open the box.
3)Can be locked, the box can be locked to prevent theft and protect your equipment.
4)Bracket,Box mounting bracket for easy fixing on the wall.
718 Electronics Communications Suppliers
Short on time? Let Electronics Communications sellers contact you.
Our featured products automatic transfer switch, circuit breaker, contactor, pilot light,relay, SPD, etc. with solid quality and considerable price and could equip them with enclosure.
12V/24V/110V/240V LED indicator light red yellow green 22mm 16mm panel pilot light
Radin Electric provides LED Pilot Light design, engineering, and full after sales support for a wide range of pilot lamp applications. We offer onsite electrical audits to assist in determining the correct product and installation to meet your exact needs and requirements.
Our featured products automatic transfer switch, circuit breaker, contactor, pilot light,relay, SPD, etc. with solid quality and considerable price and could equip them with enclosure.
Surge Protection Device (SPD)
It is a device used to limiting instant surge voltage and discharge surge current, it at least including a non-linear component.
SPD for Power Supply System Series Selection Guide
The installation of SPD at each lightning protection zone, according to the standard of low voltage electrical appearance, make classification of electrical equipment in accordance with the over voltage category, its insulation withstand impulse voltage level can determine the selection of SPD. According to the standard of low voltage electrical appearance, make classification of electrical equipment in accordance with the over voltage category as signal level, loading level, distribution and control level, power supply level. Its insulation withstand impulse voltage level are:1500V,2500V,4000V,6000V. As per to the protected equipment installation position different and the different lightning current of different lightning protection zone, to determine the installation position of SPD for power supply and the break-over capacity.
The installation distance between each level SPD should not more than 10m, the distance between SPD and protected equipment should as short as possible, not more than 10m. If due to limitation of installation position, can't guarantee the installation distance, then need to install decoupling component between each level SPD, make the after class SPD can be protected by the prior class SPD. In the low voltage power supply system, connecting an inductor can achieve the decoupling purpose.
SPD for power supply system specification selection principle
Max. continuous operating voltage: bigger than protected equipment, the system's max. continuous operating voltage.
TT System: Uc 1.55Uo (Uo is low voltage system to null line voltage)
TN System: Uc 1.15Uo
IT System: Uc 1.15Uo(Uo is low voltage system to line voltage)
Voltage Protection Level: less than the insulation withstand impulse voltage of protected equipment
Rated discharge current: determined as per to the lightning situation of the position installed and lightning protection zone.
SP1 Series
Normal Working Conditions
-Altitude not exceed 2000m
-Ambient air temperature:
Normal range: -5 ºC~+40 ºC
Extend range: -40 ºC~+80 ºC
-Relative Humidity: 30% - 90% under indoor temperature condition
- At the place without obviously shaking and shock vibration
- Non-explosion danger medium, non-corrosion gas and dust ( including conductive dust)
Classification
-As per Nominal Discharge Current:
5,10,20,30,40,60KA(8/20 µs)
- As per Maximu
It adopted double complex contact/ horizontal pulling mechanism/micro motor energy pre storage and micro-computer control technology, basically come to Zero arc ( no arcing chamber);
Adopted reliable mechanical interlock and electric interlock, executive unit adopt independent load disconnect switch, it makes more reliable and safety;
Adopt "Zero Position" technology, it can force to set to Zero Position under emergency situation ( cutoff two way power supply, meet the fire linkage requirements;
Load disconnect switch change over adopt singleness motor drive, switch over smooth and reliable, no noise, little impact;
The driving motor have instant current across only under the load disconnect switch change over, stable working status no need to provide the working current, outstanding energy saving.
Executive load disconnect switch have mechanical interlock, make sure the Normal power and Reserve Power working reliable and no interference;
Distinct ON and OFF position indicator, padlock function etc., make reliable and safe isolation between power supply and loading.
High security, high automatization, high reliability, working life more than 8000 times;
Electromechanical integration design, accuracy change over, flexible, smoothly, adopt international advanced logical control technology, high anti-interference ability, no interference outward.
Have main power ON, backup power OFF; main power OFF, backup power ON; main and backup power OFF; three working mode (I-o-II);
Easy installation, control circuit adopt plug type terminal connection
Four operating functions: Emergency manual, motor remote control, emergency OFF under auto control status, auto control operation.
Basic Type Switch Control Characteristic
Suitable for two way main and backup power system, auto transfer with auto recovery;
Can expand functions by outer connection;
Auto, Remote, Manual control functions;
Delay 0.5s signal detect, avoid miss actuation;
Under Auto control status have "O" position remote control;
Can with RS-485 communication port ( optional), according to customer required.
VOLTAGE suggesting switch panel LED Pilot Light Red/Amber/Green/White
LAD16 series pilot lamp adopts highlight solid color LED with light-emitting
chip,
featured as long service life, less power consumption, compact and small
size and light
weight, which developed to replace the XD type incandescent bulb and
neon bulb
lights. Our company launched LAD16-16C, LAD16-22B, C type, D type, E
type, H
type, bi-color light, flashing light and ultra-short pilot lamp and has win
high
reputation from the customers for its high light, reliable performance,
elegant
appearance design and workmanlike manufacture. LAD16 series pilot lamp
has the
same outlook design with LAN38 series push button, benign shock-
resistance
capability and built-in screw wiring, all the improvements made by us is to
bring
safety and convenience to our dear customer.
Functioned as an indicator, warning, emergency signal, LAD16 series pilot
lamp has
been widely applied to power electricity, telecommunication, machine tool,
vessel,
textile, printing and mining machine equipment etc. wiring system.
This series pilot lamp has national CCC certificate and is manufactured
under GB
14048.5 & IEC 60947-5-1 standards.
ESS 215KW Lithium Battery Energy Storage System 384VDC Rechargeable Lifepo4 Battery pack 280AH Energy Storage Battery
1. High energy density, small footprint, short construction period, strong environmental adaptability
2. Standardized components, modular architecture, easy for expansion
3. Battery module within the layered stack design, with more than 10 years of long design life
4. Efficient battery module and system cooling design
5. The use of international advanced IGBT and intelligent power module, with high power fast adjustment capability
6. BMS battery management system with SOC automatic calibration and high current active balance function, combined with the perfect operation control and management strategies to achieve accurate and efficient management
7. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system
8. Our BMS use NXP(USA) automotive-grade high performance chip, strong anti-interference, good reliability, wide temperature range.
9. We use brand new high quality A-grade battery power cell, longer service life.
10. Charging and discharging are controlled separately, more convenient and reliable to control charging and discharging.
11. Big color LCD touch screen display, easy setting and operation.
12. Can built in solar charge controller and AC-DC charger, our BMS can intelligently manage charger to charge battery well, BMS can communicate well with battery, solar controller, ac charger and inverter, one integrated intelligent monitoring system.
13. Approved by UL1741 certificate.
14. Accept customized product, our lithium battery system are widely used in many situations, such as: Different residential home, hotel, shop, factory, hospital, commercial buildings, electric car, RVs, Van, mobile dining car, heavy truck, different ship/boats, ice-cream car, outdoor camper,.etc.
Applications:
1.Energy Storage
--Solar-Wind Power System / City Grid (On/Off) / Community and Family
2.Back-up System and UPS
--Telcom Base / CATV system / Computer Server Center / Medical Instrumnt / Military Equipment
3.Other Applications
--Security and Electronics / Mobile POS, Mining Lihgt / Torch / LED Light / Emergency Light
--RV Motorhome /Golf Carts Battery / Boat Marine Yachts / Electric Skateboard / Electric bike / Electric Scooter / Electric
bicycle
--LED Backup / Engine Starting Battery,etc.
ESS 215KW Lithium Battery Energy Storage System 384VDC Rechargeable Lifepo4 Battery pack 280AH Energy Storage Battery
1. High energy density, small footprint, short construction period, strong environmental adaptability
2. Standardized components, modular architecture, easy for expansion
3. Battery module within the layered stack design, with more than 10 years of long design life
4. Efficient battery module and system cooling design
5. The use of international advanced IGBT and intelligent power module, with high power fast adjustment capability
6. BMS battery management system with SOC automatic calibration and high current active balance function, combined with the perfect operation control and management strategies to achieve accurate and efficient management
7. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system
8. Our BMS use NXP(USA) automotive-grade high performance chip, strong anti-interference, good reliability, wide temperature range.
9. We use brand new high quality A-grade battery power cell, longer service life.
10. Charging and discharging are controlled separately, more convenient and reliable to control charging and discharging.
11. Big color LCD touch screen display, easy setting and operation.
12. Can built in solar charge controller and AC-DC charger, our BMS can intelligently manage charger to charge battery well, BMS can communicate well with battery, solar controller, ac charger and inverter, one integrated intelligent monitoring system.
13. Approved by UL1741 certificate.
14. Accept customized product, our lithium battery system are widely used in many situations, such as: Different residential home, hotel, shop, factory, hospital, commercial buildings, electric car, RVs, Van, mobile dining car, heavy truck, different ship/boats, ice-cream car, outdoor camper,.etc.
Applications:
1.Energy Storage
--Solar-Wind Power System / City Grid (On/Off) / Community and Family
2.Back-up System and UPS
--Telcom Base / CATV system / Computer Server Center / Medical Instrumnt / Military Equipment
3.Other Applications
--Security and Electronics / Mobile POS, Mining Lihgt / Torch / LED Light / Emergency Light
--RV Motorhome /Golf Carts Battery / Boat Marine Yachts / Electric Skateboard / Electric bike / Electric Scooter / Electric
bicycle
--LED Backup / Engine Starting Battery,etc.
IP65 explosion-proof and waterproof Zone 2 inverter is the most advanced DC to AC inverter, built in low frequency isolation transformer, IP65 industrial explosion proof rating enclosure, widely used in coal mines, wineries, chemical plants.
Application:
1. Zone 1& 2 Hazardous locations, such as: underground coal mines, wineries, chemical plants, etc.
2. Environment with IIA, A A IIB, IIC types of explosive gas, such as: Flour mills, Aluminum powder plant, Metal mine factory, Graphite factory.etc.
3. Indoor (IP54) or outdoor(IP65)
4. Low noise/ Silent working mode
5. Explosion proof/ Spark-proof/ Waterproof/ Anti-dust/ Shock-proof.
Features:
1. Durable: 4.0 thick steel plate seamless welding, surface spray, beautiful appearance.
2. Explosion proof rating: Explosion-proof standard is EXdIIBT4.
3. More reliable: Built-in low frequency isolation transformer, strong ability of anti-interference.
4. Widespread application: DC to AC, Single phase to Three phase, High voltage to Low voltage or Low voltage to High voltage.
5. Pure sine wave output, quick instant response speed
6. Excellent performance of taking load, it can take a variety of loads, such as: halide lamps, motors, welding machines, precision machine tools, fluorescent lamps, energy-saving lamps, etc.
7. Powerful protection functions: With over-current, over load, under voltage, over voltage, short circuit, over heating and other protection.
8. High protection class: With good performance of anti-dust, waterproof,shockproof.
9. 100% full power output: Can be 7* 24 hours continuously working
10. Accept customized: Can be customized according to customers' requirements.
11. Adopted the sixth generation IPM intelligent power module from Mitsubishi,high efficiency and stable performance, intelligentized, modular, simple structure design, very easy and low cost for future's maintenance.
12. Advanced functions:
1) Setting flexible: The DC input voltage range, output voltage, output frequency all can be set.
2) Two kinds of work mode: Can add AC bypass input(Optional), Battery priority, AC bypass as back up or AC bypass priority, battery as back up.
3) Two kinds of start mode: Variable frequency start and Step down voltage start. with stronger capacity to drive inductive load.
4) RS485 remote monitoring(Optional)
5) Big LCD color screen display, modular structure very easy for future's maintenance
6) High efficiency > 94% and low loss, design service life > 15 years.
Product Introduction
SANDI AC/DC Charger is specially developed for DC chargers module. It has high efficiency, high power factor, high power density, high reliability advantage. AC input 3 phase or single phase, DC output voltage range from 100 to 750VDC can be set, compliant with CE safety requirements, EMC standard EN61000-6-3 and EN61000-6-1 Class A, it is an advanced international level charger module.
Unique function
High efficiency over the full load range, full load efficiency greater than 95.5%
Wide output voltage range, 100-750VDC, suitable for a wide range of Lithium and lead acid battery
5-inch LCD touch screen, easy to operate
Flexible application, charging voltage, charging current, charging time, timing charging can be set by LCD screen, easy to operate
Main features
Powerful protection, overheating, short circuit, overload, overvoltage, undervoltage, etc.
Three phase active power factor correction technology, reduces the harmonic interference to the grid
Dual DSP design, achieve the full digital control, less components means high reliability
Wide input voltage range, allows operation in most poor grid conditions
Soft start charging and soft shutdown minimize the impact on the battery.
Input, output have protective circuit breaker switch
Module adopts hot pluggable design, which is convenient for maintenance.
CAN/RS485 interface (Optional)
Our All in one system 32KWH LiFePO4 Lithium Battery with AC Charger and 12-15KW 120/240V Inverter for mobile vehicle application ESS including LiFePO4 Lithium Battery with BMS, off grid pure sine wave inverter, AC/DC charger.
This product is composed of high quality lithium iron phosphate core (series-parallel connection) and advanced BMS management system. It adopts master-slave mode, which is convenient for monitoring and controlling the input and output system. The charging and discharging are independent, it can control the charging current of the AC charger and solar controller according to the battery temperature, voltage and SOC to better protect the battery cells from overcharging, overheating and discharging. It has high reliability and long life, products developed for applications such as solar energy storage, industrial and commercial energy storage, household energy storage, charging piles, data room and other applications.
Product advantages:
All-in-one design, high integration and space saving installation
Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years
Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability
Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage
BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range
System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell
Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable;
EES All in one system 16KWH LiFePO4 Lithium Battery with AC Charger and 10KW Inverter for solar energy storage application ESS including LiFePO4 Lithium Battery with BMS, off grid pure sine wave inverter, AC/DC charger.
This product is composed of high quality lithium iron phosphate core (series-parallel connection) and advanced BMS management system. It adopts master-slave mode, which is convenient for monitoring and controlling the input and output system. The charging and discharging are independent, it can control the charging current of the AC charger and solar controller according to the battery temperature, voltage and SOC to better protect the battery cells from overcharging, overheating and discharging. It has high reliability and long life, products developed for applications such as solar energy storage, industrial and commercial energy storage, household energy storage, charging piles, data room and other applications.
Product advantages:
All-in-one design, high integration and space saving installation
Using high-performance lithium iron phosphate cells, laser welding, good cell consistency, designed service life of more than 10 years
Charging and discharging are controlled separately, which is convenient and reliable to control charging and discharging. The discharge port will not be disconnected when over-charging, and the charging port will not be disconnected when over-discharging, the system has good stability
Master-slave mode, passive equalization, can manage the equalization resistance, can set the equalization start voltage difference, and monitor the equalization resistance temperature, more intelligent and safe, and reduce the impact of barrel effect on system energy storage
BMS adopts NXP(USA) automotive-grade high-performance chips, with strong anti-interference, good reliability and wide temperature range
System parameters can be set through the host computer, such as fan start/stop temperature, charger maximum current setting, charge and discharge current correction, SOC correction, with insulation leakage detection function to prevent oil leakage and short circuit of the cell
Integrate Solar charge controller or AC charger optional, BMS communication control, more safe and reliable;
1, The core components are all imported, adopting the sixth generation IPM module from Mitsubishi, which has stable performance, long service life, strong protection functions and convenient replacement and maintenance.
2, Adopt the central processor DSP28335 chip from American TI Company, respond quickly and accurately, and provide stable and clean power for the load to provide protection.
3, The whole machine adopts modular design and plug-in design, which is convenient for maintenance and reduces the hidden cost of machine failure to repair.
4, According to the product configuration conditions, adjustment the system usage mode: DC(Battery/Solar) priority or AC mains bypass priority can be set.
5, Two kinds of start mode: Reduction Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. This function is very convenient for users and also reduce frequency converter's usage, which reduced the cost of equipment investment, easy to connect wires and control.
6, The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy ±1%.
7, The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel.
8, Output AC Power is suitable for all types of electrical equipment, CNC machines, electric tools, motors, pump and air conditioner etc. It has higher efficiency and higher capability of driving load.
9, Humanized safety design, using isolation transformer design, input and output are completely electrically isolated, input and output are equipped with circuit breakers, which saving costs for the user and easy to installation, the electric parts are completely closed to prevent electric shock.
10, Wide input voltage can be set according to customerâ??s requirement. Input voltage range can be selected from 100-300V, 200-500V or 500-850V, suitable for solar/wind system without backup batteries, it can save many cost and maximization use the solar/wind energy.
11, Using SVPWM space vector algorithms, high conversion efficiency, high instantaneous power and low losses conversion efficiency up to 94%.
12, Powerful data display function. LCD + LED display, can display input and output voltage, current, KWH, fault display, convenient for customers to quickly find faults and guide maintenance.
13, European CE (EMC, LVD, UL1741) and ISO9001 certificates.
1, The core components are all imported, adopting the sixth generation IPM module from Mitsubishi, which has stable performance, long service life, strong protection functions and convenient replacement and maintenance.
2, Adopt the central processor DSP28335 chip from American TI Company, respond quickly and accurately, and provide stable and clean power for the load to provide protection.
3, The whole machine adopts modular design and plug-in design, which is convenient for maintenance and reduces the hidden cost of machine failure to repair.
4, According to the product configuration conditions, adjustment the system usage mode: DC(Battery/Solar) priority or AC mains bypass priority can be set.
5, Two kinds of start mode: Reduction Voltage Start and Variable Frequency Start. Customers can set start mode according to the type of their load. This function is very convenient for users and also reduce frequency converterâ??s usage, which reduced the cost of equipment investment, easy to connect wires and control.
6, The output voltage can be set between -40 % to +20 % of rated voltage. And the output voltage is very accuracy �±1%.
7, The DC input voltage range can be set. Over-voltage point, under-voltage point, over-voltage recovery point, under-voltage recovery point all can be setting via the LCD panel.
8, Output AC Power is suitable for all types of electrical equipment, CNC machines, electric tools, motors, pump and air conditioner etc. It has higher efficiency and higher capability of driving load.
9, Humanized safety design, using isolation transformer design, input and output are completely electrically isolated, input and output are equipped with circuit breakers, which saving costs for the user and easy to installation, the electric parts are completely closed to prevent electric shock.
10, Wide input voltage can be set according to customer's requirement. Input voltage range can be selected from 100-300V, 200-500V or 500-850V, suitable for solar/wind system without backup batteries, it can save many cost and maximization use the solar/wind energy.
11, Using SVPWM space vector algorithms, high conversion efficiency, high instantaneous power and low losses conversion efficiency up to 94%.
12, Powerful data display function. LCD + LED display, can display input and output voltage, current, KWH, fault display, convenient for customers to quickly find faults and guide maintenance.
13, European CE (EMC, LVD, UL1741) and ISO9001 certificates.
[Optional]
A, RS485 communication;
B, AC bypass complementary function;
C, Built-in charger
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
Product Features:
1. Standardized components, modular architecture, easy for expansion
2. High energy density, small footprint, short construction period, strong environmental adaptability
3. Battery module within the layered stack design, with more than 10 years of long design life 4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH-500KWH optional
5. The use of international advanced Mitsubishi IPM module and intelligent power module, with high power fast adjustment capability
6. BMS battery management system with SOC automatic calibration and high current active balance function, combined with the perfect operation control and management strategies to achieve accurate and efficient management
7. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system
8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform
9. PV charge controller adopts three charging stages (buck charging, equalize charging and float charging) which can maximize the utilization of PV modules and batteries
10. Colorful LCD display all module working information and status.
ESS lithium battery system is composed of lithium battery modules, BMS system, PV charge controller, AC/DC Charger, central control unit CCU, temperature detector, integrated structure and other parts; the solar panels in the system are battery storage and power for output; BMS module completes the detection and control of voltage, current, temperature, SOC, SOH and charging and discharging related parameters of power battery pack; PV controller and inverter realize bidirectional AC/DC function to meet the charging and discharging conversion demand of power battery pack; each detector is used to monitor the ambient temperature in real time to ensure the safety of the system.
Product Features:
1. Standardized components, modular architecture, easy for expansion.
2. High energy density, small footprint, short construction period, strong environmental adaptability
3. Battery module within the layered stack design, with more than 10 years of long design life
4. Long Cycle Life LiFePO4 Lithium ion Battery system from 20KWH--500KWH optional
5. BMS battery management system with SOC automatic calibration and high current passive balancing function,
combined with the perfect operation control and management strategies to achieve accurate and efficient management
6. The combination of software and hardware protection, with alarm protection and automatic diagnostic functions, improve the protection strategy to ensure safe and efficient operation of the system.
7. Our BMS system adopts American NXP automotive grade chips with high performance.
8. Product communicates with the monitoring platform in real time through RS232, CAN communication interface, and reports various records in time to ensure real-time monitoring of the battery pack of the monitoring platform.
9. Colorful LCD display all module working information and status.
718 Electronics Communications Suppliers
Short on time? Let Electronics Communications sellers contact you.
