Their high torque transmission capacity covers a speed range from 360 to 1800 rpm depending on size and reduction and a torque power speed(N/n1) capacity from 0.38 up to 46.2 for reduction from 2 up to 6: 1.
The design family has six different modesl, four reverse reduction gears and two reduction gears without reversing function-each divided into eleven size. The relative configuration of input and output shaft is eighter coaxial or offset, the latter eigher vertically, horizontally or diagonally. The modular design affords a variety of advantages including low-cost-manufacture and spare stocking.
Marine gears of the design type GCS and GCH are single stage reduction gears with case hardened and ground single helical spur wheels. GCS type gears are of vertical offset design. GCH gears have horizontal offset shafts.
The sizes GCS/GCH 450 to 560 are equipped with antifriction bearings. The sizes GCS/GCH 600 to 1000 are equipped with plain bearings.
All gears can be equipped with a power take off (PTO) for which special superposition gears have been developed.
Marine Anchors for ships and boats are produced with state-of-the-art casting technologies (except welding anchors) in . We have improved the existing casting process by simulating existing casting processes. With optimized ingate position,added riser and densener,the possibility of casting shrinkage is greatly reduced. Meanwhile, the MAGMA software is employed to simulate the casting process, which can accurately reflect various changes in the casting process. This is convenient for our engineers to observe the entire casting process more intuitively, and accurately predict the actual design by observing the possible defects and their occurrences. Through these methods, we can avoid problems that may arise in production, and improve casting efficiency and accuracy, so as to reduce costs and speed up delivery.
Welded Anchors are also in our scope.
Nominal Weights Range:
1KG-55000KGS
Available Types(some anchors are not listed) :
AC-14 HHP high holding power anchor
Pool anchor
Spek anchors
Hall anchor
D-hone anchor
Japan stock anchor
Japan stockless anchor
U.S.N.(navy) stockless anchor
Admiralty anchor
Single fluke anchor
Matrosov anchors
Marine gratings and marine grilles fully comply with CBT608 and CBT615.
Steel and stainless steel gratings are produced mainly by welding. First, we will punch or slot the flat steel, then place the crossbar into the hole for spot welding. Each contact point of the cross bar and the flat steel is properly welded. The crossbar can also be welded by spot welding. welding staff have the top grade industry profession certification
The base of the grilles or gratings could be material of steel ASTM A36, stainless steel 1cr18ni9ti, FRP,polyester and etc.
Our new product molded polyester grating is using glass fiber as the reinforcing material, using the unsaturated polyester resin as substrate and then specially processed and compounded to be strong and anti-slip.
Our grilles could be used as bilge suction grilles for shipbuildiing, deck walkway gratings, Marine submarine door grilles and etc.
340 Marine Paint Suppliers
Short on time? Let Marine Paint sellers contact you.
Customized solutions for various marine winches, including electric winches, hydraulic winches, mooring winches, towing winches, slipway winches, tugger winches, positioning winches and combined drum anchor winches. Feel free to contact us for a free quote!
Marine JIS standard cast iron valve
Marine JIS standard cast steel valve
Marine JIS standard Bronze (Brass) valve
Marine JIS standard gate valve
Marine JIS standard Butterfly valve
Marine JIS standard down storm valve
Marine Air Pipe (vent) Head (JIS/DIN/NIIKURA)
Marine JIS standard Bronze/Brass/Cast iron hose valve
Marine Accessories and Fitting
Air pipe (vent) head Accessories and Fitting.
Ship MES Marine Evacuation System is fabricated in accordance with latest IMO LSA SOLAS specifications. MES provides a safe passage from boarding locations to floating platforms or survival crafts for people of all ages, statures and physiques, wearing approved life jackets. The advantage is that it can fully consider the situation of passengers of different ages, taking into account their sizes and different physical conditions, so that they will not physically touch the sea and quickly enter the survival craft. With the help of the MES, all personnel can be evacuated from the ship to the survival craft within 30 minutes after the ship abandonment signal is issued.
Available Types:
slide marine evacuation system
Chute marine evacuation systems
The marine accommodation ladder is used to board or disembark for the crews. Our marine accommodation ladder is made of aluminum or steel.
Marine Accommodation Ladder is a facility for crew to board or leave the ship. It is one of the most common outboard ladders. It is commonly used for cargo ships, oil tankers, passenger ships and other large and medium-sized ships. The Accommodation Ladder system consists of a ladder and its retracting mechanism, generally located above the bulkhead or freeboard deck, where the side is not closed by the outer slab. When in use, the ladder is removed from the ship by means of the retracting mechanism, and the hull plate is placed obliquely next to the ship for the personnel to board the ship; when not in use, the ladder should be retracted and fixed at the outboard deck.
The Major types we have are as follows,
A. Marine Modular type
B. Marine Aluminium type
Available IACS Certs: ABS, BV, CCS, DNV-GL, KR,LR, RINA, NK,RMRS and etc.
Marine Double Bollard
1) Material: Cast Steel (ZG230-450), Q235
Also we can supply other kinds of bollards like Single Bollard, Cross Bollard, Inclined Bollard , etc
2) Paint: Surface Epoxy Primer
3) Certificate: CCS, ABS, BV, etc
With good quality and low price.
Stadard: SOLAS
Application:
1 For protection doing leisure
2 Outside material :Terylene Oxford textile
3 Inside material :EPE foamed polyethylene
4 all size lifejackets apply to SOLAS standards
5 Used for the seaman and passenger in sea or river
Type: vertical evacuation system / inclined evacuation system
Max.certification n8umber of persons of system: 330-700 persons
Numbers of person carried by platform: 50-100 persons
Max. height of stowage(above the waterline): 4.8-12m
Weight: less than 2600kg
Type CRP20 CRP42 CRP85 CRP168
Input power max.(KW) 45 100 210 300
HP 61 135 285 400
Input torque max.(Sf=1) 200 420 850 1675
Input speed max. 2300 2500 2350 2000
Reduction Rate i I 1.93 2.5 2.68 3.46
I up 1.7 1.64 1.65 1.53
I down 1.13 1.52 1.62 2.26
propeller diameter Max. 500 800 950 1150
Min. 700 900
PAL length* Max. 2250 2800 2800 4250
Min. 350 875 980 1400
Weight (including blades, lubricating oil, and the minimum PAL) 65 190 300 1370
PAL increase the weight of kg per 100mm 8 9 20.4 40
PAL is the vertical distance from the center line of the center line of the power input flange.
In wall panels, they could be widely used in curtain walling for landmark buildings like as airports, exhibition centers and starred hotels etc.
Product description:
1.Name:aluminium plate
2.Alloy no.:1050 1060 1100 3003 3004 3104 3005 3105 5005 5052 8011
3.Size:thickness: 0.2-150mmmm(tolerance:+/-0.02mm)
Width:500-2400mm(tolerance:+/-1mm)
Length:500-10000mm(tolerance:+/-1mm)
4.Application:
Building material , insulation, shoes &tents eyes, corner beads, automotive industrial, pop can bottle and cap, deep-proceeding case, light industry, tv back board, street sign, pp caps, cell mask and so on.
