The poly-v belts provide smooth running, low noise operation at high speeds, small pulley diameters and large transmission ratios. These belts are excellent in serpentine applications. PJ, PL, PM
Wide comfort pad to provide lumber support for long working hours.
Fully Adjustable
Two lateral D-Rings for work positioning
Tool holding webbing loops.
Rings for tool holders, Bolt Bags etc.
Conforms to EN 358 : 2000
Ratchet Tie Down bind/Cargo lashing Strap
Description:
ITEM# : RT-25.5MS1
Description:
1'' Cargo lashing end s hook-PE coated,
Safety Working Loading(SWL): 550kgf,
Webbing Width: 25mm,Total Length: 5m.
Size of Components: End with dia.7x1"x83mm S hook PE coated.
===
ITEM# : RT-25.5MS.
Description: 1'' Cargo lashing end s hook-PE coated, Safety Working Loading(SWL): 550kgf , Webbing Width: 25mm, Total Length: 5m, Size of Components: End with dia.7x1"x103mm, S hook PE coated.
===
ITEM# : RT-25.5MJ,Description: 1" Cargo lashing ends double J hook, Safety Working Loading(SWL):550kgf, Webbing Width:25mm, Total Length: 5m Size of Components: end with dia.6.5x1"x47mm double J hook
ITEM# : DR-4504
Shape: Double D Ring (BENT)
Material: Aluminum
For 45mm Wide Webbing
Safety Working Loading (SWL) Strength:30kN/35kN
Weight: 73g
Width: 46 mm
Length: 111 mm
Finish: Anodized or Polishing
Automotive Poly-V Belts are engineered with the highest performance synthetic elastomers combined with reinforced fibers that ensures high heat resistance. These belts have the best transmission efficiency due to its characteristic multiple V-Ribs that delivers power from Engine Crank Shaft to Alternator/Dynamo, A/C Compressor, Power Steering Pump and Water Pump.
Industrial Poly-V Belts, with its characteristic V-Ribs which are resistant to oil and temperature stress. The beltâ??s design allows us to deliver outstanding performance at high speeds on smaller diameter pulley.
2361 Industrial Belts Straps Suppliers
Short on time? Let Industrial Belts Straps sellers contact you.
Our Raw Edge Cogged Belts (Classical, Wedge, Banded, VS, etc) are engineered with high performance synthetic elastomers that ensures high heat resistance. These belts have excellent wear resistance and bending stress resistance due to the cogged profile that enhance the durability.
Raw Edge Cogged Belts are recommended in high speed Industrial power transmission drive running 24 X 7 where critical machine designs that need high durability between changes. Also, the Raw Edge Cogged Belts are most efficient replacement for Conventional Classical Wrapped belts at no cost for pulley change and smaller pulley drive designs.
Our V-Belts (Classical, Wedge, Banded, Hexagonal, Etc) are designed with Premium Quality Ingredients to deliver state of the art performance for high speed and high torque drives with significant and solid transmission capabilities resulting in longer service life. Our belts are constructed with high tensile, stiffer polyester cords along with abrasion resistance Cover Fabric.
Also Customer specified compound combination can be manufactured based on requirement.
The BuMtresD heavy duty conveyor pre-cleaners can tackle the bulk material transportation worksite with fast running belt and heavy load demand. The blades provides better cleaning effects for high-speed belts, large head pulleys and large sizes and volumes of material, typically found in (above and below ground mining).
Used for packing heavy goods like pallets, bricks, pavers blocks and many more product.
This strap is made of only Plastic and give option for steel strapping.
very easy to use.
cheaper in compare of steel strap.
UV protected.
Polyester Woven Strapping
13mm to 25mm width , with strength of 450daN to 1900daN
Woven strapping belts are made of high tensile polyester yarns. Due to its material characteristics it has low elongation (below 10%), is highly tear proof and absorbs very little moisture. Furthermore the strapping can be retensioned in case of volume loss in the packaged goods and has a high breaking load, linear and within the system. Woven strapping belts will not splice, are flexible and universally applicable.
Specifications
no damage to most surfaces
no corrosion & easy handling
low investment cost
high shock absorption
a small, manageable system
limited resistance against lyes and acids
no risk of injury for shippers and consignees in using or opening the strapping
available width 13mm to 25mm
linear breaking strength available from 295 to 1500 daN
special glue coating for usage
for baling press machines available with special glue coating
Polyester Woven Strapping
13mm to 25mm width , with strength of 450daN to 1900daN
Woven strapping belts are made of high tensile polyester yarns. Due to its material characteristics it has low elongation (below 10%), is highly tear proof and absorbs very little moisture. Furthermore the strapping can be retensioned in case of volume loss in the packaged goods and has a high breaking load, linear and within the system. Woven strapping belts will not splice, are flexible and universally applicable.
Specifications
no damage to most surfaces
no corrosion & easy handling
low investment cost
high shock absorption
a small, manageable system
limited resistance against lyes and acids
no risk of injury for shippers and consignees in using or opening the strapping
available width 13mm to 25mm
linear breaking strength available from 295 to 1500 daN
special glue coating for usage
for baling press machines available with special glue coating
The market of tensioner is already overflown with cheap models made in China.
Our T-50 tensioner is made in China too, but it contains advanced German engineering and knowledge.
While most of the cheap models are based on a ratchet system our model is equipped with two anti cycling one-way bearings.
These bearings make the tensioner more durable and easier to handle. Less force is needed during the tensioning.
The special designed breakle shoe is made for all our strapping systems.
High quality composite will be protected. The integrated stainless steel cutter will easily cut any belt.
Strapping Ratchet for straps from 30 to 50mm ( 1 1/5 to 2" )
May the force be with you...
Heavy-duty challenges needs heavy-duty tools.
The RT- 50 XXL Ratchet is made for tensioning big and strong belts.
This ratchet type tensioner can be used for any kind of strapping system of 25 to 50 mm width.
The design of these big tools is made to be as light weighted as possible and the wide tension angle gives you maximum
tensioning strength at minimum force.
Description
HUATAO AEROGEL is the most effective high-temperature insulation material in the industrial market, typically 2-5 times thinner than other widely used insulation products. It is our easiest product ever to handle, store, and install.
Kevlar Conveyor Belt For Aluminum Extrusion
Description
Seamless Kevlar Felt Conveyor Belt also called 100% kevlar felt belt, kevlar belt, high temperature felt belt, belt for aluminum extrusion. The Kevlar felt belt is suitable for first-class and second-class cooling bed of felt belt type production line. The felts provided by our company have good resistance to hardening and abrasion and the highest temperature resistance reaches 500 ° C (carbonization temperature). The company's rolling Kevlar fiber produced by the United States DuPont. Available in green (Kevlar + carbon) and yellow (100% Kevlar) materials for use on sliding tables in aluminum extrusion press cooling beds. This product features similar to Kevlar conveyor belts and is mainly used in the high temperature areas of translation step cooling beds.
Specification
Color:Yellow
Material:Kevlar + one layer base cloth
Temperature Resistance:500?
Available size:As your demands
Commonly used thickness recommend:8mm
Color:white yellow green brown
Advantage
1 Heat resistant up to 500?
2 No elongation under high tension and heavy load
3 No seam, splice or joints: no breaks due to weak zone,High density structure
4 Smooth and even belt surface: scratch-free extrusions
5 Excellent belt tracking on the cooling table
6 Low heat conductivity and high density with good wear resistance and impact resistance property under heavy conditions
Applied environment
Corrosion resistance, acid resistance, heat resistance, moisture proof, oil resistant, alkali resistant, antistatic and wear resistant, resistant to burn, hardy, slip resistance, flame retardant, resistance to high temperature
Description:
Kevlar endless belts are mainly used in pick-up and the first-stage cooling table. Our Kevlar endless belt is very good in temperature resistance (500?)and anti-abrasion.
Specification:
Material:PU felt+synchronous belt(hot melt bonding)
Temperature Resistance:180?600?
Length:2000mm25000mm
Width:20mm200mm
Total Thickness:6mm 8mm 10mm 12mm
Feature:Strong tension,no deviation,non slip,low noise
Application Area:2500T10000T Extrusion production line
Application:
Mostly suitable for the aluminum profiles with the high quality surface requirement,avoid the loss in second operation's and transit bumps or rub when in roduction.
Description:
Heat Transfer Printing Belts are produced from 100% Nomex fiber. They are the most important component of the heat transfer printing machines. We can offer the felts with the normal and special size according to customer?s request.
Felt Features: needled felt, smooth surface,elastic, non-off tracking.
Heat Transfer Printing Felts are used on the following machines : Monti, Lemaire, Bater, Stork, Futanet, Gessner etc.
Specification:
Material:100%Nomex
Temperature:220°c ~ 280°c
Colors:White
Density:2800g/m2- 3600g/m2
Function:Belt Conveyor Part
Place Of Origin:China
Delivery Time:Within 15 Days Delivery After Receipt Your Payment
Advantage
1. Selection Of Brand Raw Material,Common Specifications Have Temperature 160-180? And 220-280?.
2. The Felt Belt Contains Heat Shrinkable Fiber Material Inside,The Felt Will Automatically Shrink After Heating,Wrapped Tightly.
3. The Belt Surface Formation,Uniform Density,Good Resistance,Long Work Life.
Application
1. Selection Of Brand Raw Material,Common Specifications Have Temperature 16-180? And 220-280?.
2. The Felt Belt Contains Heat Shrinkable Fiber Material Inside,The Felt Will Automatically Shrink After Heating,Wrapped Tightly.
3. The Belt Surface Formation,Uniform Density,Good Resistance,Long Work Life.
Direction of our felt belt
1. The blanket must be install as the direction of the arrow, fixing both sides of the perimeter
to see if the perimeter is the same.
2. Adjust the machine pressure within 2kg. heat up to 150 ?, idle for 2 hours; heat up to
170?, idle for 2 hours; heat up to 190?, idle 3 hours( important); heat up to 200?,
idle for 2 hours.
3. Then the belt will suitable for your machine, you can adjust the machine pressure in 3--5kg
according to your needed and start to printing.
2361 Industrial Belts Straps Suppliers
Short on time? Let Industrial Belts Straps sellers contact you.
