Weight:20kgs/ctn
1)test injecting angle, atomization, dribbling and automatic testing and cleaning Press auto key. The pump start to work automatically, after work over, the pump turn off automatically, the injector keep injecting for 15s, the time valve decrease to 0, can observe the injecting angles, atomization and volume, replace or clean the injector, if appears gush, unusual angels and unusual volume, stop injecting for 30s, and observe injecting volume, time value shows 30s, the liquid will back to the fuel tank in the following 30s, then start dribbling testing for 60s, if no dribbling, the unit will starts regular testing automatically. 2)test mode at idling speed Conduct the injecting test as follows: Injecting rpm: 1600r/min Pulse width: 2.2ms Count: 3000 Timing: 112s When the producer is over, observe the injecting uniformity, and replace or clean it if the volume over 9% 3)test mode at maximum loading Conduct the injecting test as following: Injecting rpm: 4000r/min Pulse width 2.8ms Count 3000 This program can observe the injecting volume at the maximum loading 4)test mode at high speed Conduct the injecting test as following: Injecting rpm: 6500r/min Pulse width 2.5ms Count 4000 Timing 36s This program can observe the working state at the high speed. 5)test injecting with complete procedure During this procedure pulse width is 2.2ms, rpm is 1600r/min, then the rpm will up to 9975r/min, pulse width will up from 3ms to 12ms, then down to 1.1ms.Total cycle is 5 times, and running time is 20s, observe for 30s after the test, then the liquid will return for 30s. During the automatic test, press selection to pause it as you need. 53.5*48.5*55.5
Description: The functions as following: 1o test and analyze the injecting state. 2o test the injector dribbling. 3o test the injecting angle and atomizing. 4o test the injecting volume. 5o test the injector uniformity. 6o test conduct the physical and chemical cleaning of the blocked or trouble injector, ultrasonic cleaning, test cleaning nd on-vehicle cleaning. 7o test the open and close injecting pressure of the injector. 8can clean the engine without dismantling (choose matched connector). 9can operate the auto static testdynamic test and selective test with the injecting dribblinganglesatomizationuniformity of one or more(1-4) injectors, can simulate any state of the vehicle to observe the complete process of injectors. 10.Can operate automaticallyreverselyand ultrasonic cleaning with one or more injectors at different
Features: 1. LCD display; 2. Ultrasonic cleaning trough built-in; 3. CE certification; 4. Tool trolley to make it more convenient; 5. Equipped with high quality Siemens pump to make it endurable; Functions: 1. Ultrasonic cleaning, dismantle the carbide of the injector; 2. Injector test, stimulate engine running condition, test injector in different speed range. Check and test injector's injection situation: atomization/spraying angle/spraying amount/spraying uniformity; 3. Leakage and block test; 4. Uniquely designed various compound bonder for all kinds of side-inlet injectors; 5. With reverse flush function, to clean inside out, to improve clean efficiency; 6. With a set of adaptor to clean injectors without dismantling it from the engine. Turning speed range: 0~15000r/min Timing pulse length: 0~9900times/step length 100 Pulse length: 0-20ms step length 0.1ms Timing: 0~10min System pressure: 0~0.6Mpa Ultrasonic cleaning power: 70W Power supply: AC220(110V)+-10% 50/60Hz Working temperature: 10¡ãC~40¡ãC Stimulant signals: 0+-5V Output scope of the pulsed signals: +5V,+12V.
Fuel Injector Tester & Cleaner: Technical parameter: Range of turning speed: 7500r/min Pulse width by counting: 9900 step length 100 PWM: 20.0ms step length 0.1ms Timing measurement: 20mins(adjustment) Pressure of system: 0.6Mpa(adjustment) Power supply: AC220V±10 50/60Hz Oil tank capacity: 2000 ml Ultrasonic cleaning power: 70Wintermittent Ultrasonic cleaning frequency: 28KHZ±0.5 KHZ Measuring cylinder capacity: 140ml Measuring cylinder precision: 2ml Output scope of the stimulant signals: 0~+5V Output scope of pulsed signals: +5V +12V Features: 1. It is initiated that the unit is operated by touch screen and LCD with Chinese characters. 2. 6 lines simulated input signals are used for the sensor of simulate input. 3. 2 lines pulsed input signals are used for the sensor of simulate input. 4. 8 lines input signals instead of sensor test the computer of automobile to find out the fault of sensor. 5. 16 kinds testing & cleaning functions for fuel injector -
Power: 85-132vac/170-264vac 47-63hz Fuel tank capacity: 2.5l Test tube capacity: 120cc Ultrasonic wave frequency: 38-39khz Ultrasonic wave power: 100w Rotate speed: 0-9975r/min, step: 25r/min Pulse width: 0-30ms, step: 0.1ms Count: 0-9975r, step: 25r Time: 0-9975s, step: 5s System pressure: 0-6.2kg/c©o (variable regulated£© System flow: 4l/min Test cylinder: 6 (max) Dimensions: 400mm ¡á 510mm ¡á 450mm Weight: 25kg
Description: 12 internal transducers Multi transducer systems offer a more effective and economical cleaning programme. Stand alone electrical generator Separate generator offers more protection against damage and ease service. 3 metre connecting cable 3 metre cable allows safe and secure location of important power supply. Double skinned tank Double skinned tanks give greater protection and long life. Finished in polished stainless steel Polished stainless steel is easy to clean and maintains a professional look. Internal drain & debris tracks Drain/debris tracks retain debris and maintains effective cleaning process. 12mm drain tap Allows quick draining of waste cleaning fluid. Complete with: lid and parts basket Lid keeps fluid clean and reduces fluid evaporatio
Description: The functions as following: 1 to test and analyze the injecting state. 2 to test the injector dribbling. 3 to test the injecting angle and atomizing. 4 to test the injecting volume. 5 to test the injector uniformity. 6 to test conduct the physical and chemical cleaning of the blocked or trouble injector, ultrasonic cleaning, test cleaning and on-vehicle cleaning. 7 to test the open and close injecting pressure of the injector. 8 can clean the engine without dismantling (choose matched connector). 9 can operate the auto static testdynamic test and selective test with the injecting dribblinganglesatomizationuniformity of one or more(1-6) injectors, can simulate any state of the vehicle to observe the complete process of injectors. 10 can operate automaticallyreverselyand ultrasonic cleaning with one or more injectors at different
Supplier: Fuel injector tester & cleaner equipments
