Surge Protective Device

Class B / Type I Class C / Type II Class D / Type III Data Surge Protection PoE Surge Protection Signal Surge Protection

Our featured products automatic transfer switch, circuit breaker, contactor, pilot light,relay, SPD, etc. with solid quality and considerable price and could equip them with enclosure. Surge Protection Device (SPD) It is a device used to limiting instant surge voltage and discharge surge current, it at least including a non-linear component. SPD for Power Supply System Series Selection Guide The installation of SPD at each lightning protection zone, according to the standard of low voltage electrical appearance, make classification of electrical equipment in accordance with the over voltage category, its insulation withstand impulse voltage level can determine the selection of SPD. According to the standard of low voltage electrical appearance, make classification of electrical equipment in accordance with the over voltage category as signal level, loading level, distribution and control level, power supply level. Its insulation withstand impulse voltage level are:1500V,2500V,4000V,6000V. As per to the protected equipment installation position different and the different lightning current of different lightning protection zone, to determine the installation position of SPD for power supply and the break-over capacity. The installation distance between each level SPD should not more than 10m, the distance between SPD and protected equipment should as short as possible, not more than 10m. If due to limitation of installation position, can't guarantee the installation distance, then need to install decoupling component between each level SPD, make the after class SPD can be protected by the prior class SPD. In the low voltage power supply system, connecting an inductor can achieve the decoupling purpose. SPD for power supply system specification selection principle Max. continuous operating voltage: bigger than protected equipment, the system's max. continuous operating voltage. TT System: Uc 1.55Uo (Uo is low voltage system to null line voltage) TN System: Uc 1.15Uo IT System: Uc 1.15Uo(Uo is low voltage system to line voltage) Voltage Protection Level: less than the insulation withstand impulse voltage of protected equipment Rated discharge current: determined as per to the lightning situation of the position installed and lightning protection zone. SP1 Series Normal Working Conditions -Altitude not exceed 2000m -Ambient air temperature: Normal range: -5 ºC~+40 ºC Extend range: -40 ºC~+80 ºC -Relative Humidity: 30% - 90% under indoor temperature condition - At the place without obviously shaking and shock vibration - Non-explosion danger medium, non-corrosion gas and dust ( including conductive dust) Classification -As per Nominal Discharge Current: 5,10,20,30,40,60KA(8/20 µs) - As per Maximu

Specification: Square : 22mm Voltage : 130v ac (rms) IN : 7.5ka Imax : 15ka Application : specially used for power strip or socket Features: With built-in thermal cutoff (thermally protected) Two types : square and round type Used for power strip Different size : 8 to 34mm Peak current (8/20) : 3 to 40ka (maximum) Certificates : 1449 3rd, T & UUML.

800_080 BT P B80 385 RM Main Features: * Small volume, high discharge capacity * Reliable protection thanks to double control disconnector * Quick response * Low voltage protection level and with double terminals connection * Green window will change when fault occur, also in the same time provide remote alarm terminal * Core components are from international well known supplier Application: This product is designed to protect low voltage devices from surge damage, used in power supply system such as power distribution-room, distribution-cabinet and other important power supply system. Widely used to protect mobile communication station, telecommunication centre, civil aviation, finance, and so on. Specifications: Technical data Rated voltage (max. continuous voltage) Uc 385V Nominal discharge current(8/20) In 35kA Max. discharge current Imax 80kA Voltage protection level at 20kA Up í_1.8kV Response time tA í_25ns Operating temperature range -40íµí¡+80íµ Cross-sectional area 1.5mm2~25mm2(solid)/35mm2(flexible) Mounting on 35mm DIN rail Test standards GB 18802.1-2002; IEC 61643-1:1998-02 Dimension 3 mods

Video signal arrestor Applications: Designed for monitor device not to be spoiled by lightning over-voltage, induced over-voltage and static discharge. Video camera E1, pdh, sdh, spdh Digital hard disk video cassette recorder Industrial control Features: Multi. Protection circuits, gas-tube+ tvs technology Dual protection in common module and different module Tvs array technology, low capacitance Multi-strike capability Specifications: Type d12bf d12bf-4d12bf-16 Electrical specifications Impedance75++ Max operating voltage12v Nominal discharge current (8/20++s)3ka Max. Discharge current (8/20++s)5ka Protection level (3ka 8/20++s) Line to line40v Line to pe160v Adapt transmission rate100mbps Insertion lossf 0.5db Response time f 5ns Mechanical specifications Connectorbnc female to malebnc female to female Number of protection ports1416 Diamension (mm)82.7*25*25130*73*25 481*84*47 Working environments Operating temperature minimum-40 Operating temperature maximum85 Operating humidity95%

Applications: Designed for monitor device not to be spoiled by lightning over-voltage, induced over-voltage and static discharge. Video camera E1, pdh, sdh, spdh Digital hard disk video cassette recorder Industrial control Features: Multi. Protection circuits, gas-tube+ tvs technology Dual protection in common module and different module Tvs array technology, low capacitance Multi-strike capability Specifications: TypeD12bfD12bf-4D12bf-16 Electrical specifications Impedance75+ Max operating voltage12v Nominal discharge current (8/20s)3ka Max. Discharge current (8/20s)5ka Protection level (3ka 8/20s)Line to line40v Line to pe160v Adapt transmission rate100mbps Insertion loss_0.5db Response time _5ns Mechanical specifications ConnectorBnc female to maleBnc female to female Number of protection ports1416

Applications: Designed for Ethernet device not to be spoiled by lightning over-voltage, induced over-voltage and static discharge. CAT6, CAT5e and CAT5 compatible 10/100/1000 Base-T Gigabit Ethernet protection LAN, FDDI, CDDI, ATM PDH, SDH, SPDH Industrial control Features: Multi. Protection circuits, Gas-Tube+ TVS technology Dual protection in Common module and different module TVS array technology, low capacitance Multi-Strike Capability Specifications: TypeD05J4D05J8HD12Y4D36Y2 Electrical Specifications Max operating voltage5V5V12V36V Nominal discharge current (8/20»s)3kA2kA3kA3kA Max. discharge Current (8/20»s)5kA3kA5kA5kA Protection level (3kA 8/20»s)Line to line25V25V40V60V Line to PE160V Adapt transmission rate100Mbps1000Mbps10Mbps10Mbps Insertion Loss_0.5dB Response time _5ns Mechanical Specifications ConnectorRJ45 Protection Lines 1,2 & 3,61,2,3,4,5,6,7,84 lines2 lines Form Size(mm)83 * 25 * 25 90 * 14 * 63 Working environments Operating Temperature Minimum-40 Operating Temperature Maximum85 Operating Humidity95%

Supplier: Surge Protection Devices, Lightning Arresters

Supplier: Surge Protection Devices, Lightning Arresters