Hydraulic Counterbalance Cartridge Valve

Zander is from a hydraulic manufacturing company in Greece. In the first half of this year, their company planned to upgrade the old logistics crane and put it back on the market. Its main goal is to improve its stability by 20% compared with its peers. The optimization of the hydraulic cartridge counterbalance valve is the key, but the original hydraulic cartridge counterbalance valve manufacturer has no ability to innovate. Zander found a local hydraulic cartridge valve manufacturer to optimize the structure and make samples. However, during commissioning, when the load of the system drops, the pressure fluctuation cannot exceed that of the peers, and the hydraulic cartridge counterbalance valve cannot avoid load interference. The local hydraulic cartridge valve manufacturer has no ability for further improvement. 2 months passed by, but there was still no solution. The boss pushed for progress many times, and Zander was worried. Zander found AAK on Google, noticed that AAK had released some customer cases about hydraulic cartridge counterbalance valves, and sent us an email. According to the schematic diagram of the hydraulic system and the original hydraulic cartridge counterbalance valve drawing provided by him, AAK engineer informed that the structure optimized by his local hydraulic cartridge valve manufacturer was not reasonable and needed to be adjusted. AAK has a trick to prevent the hydraulic cartridge counterbalance valve from being affected by the load. Zander asked for AAK samples. After 45 days, AAK sent 20 samples of hydraulic cartridge counterbalance valves. 3 months later, Zander sent an order for 500 hydraulic cartridge counterbalance valves, and told us that their technical department was very satisfied with AAK hydraulic cartridge counterbalance valves. Not only did they overcome the load impact, but also improved the stability of their new logistics crane by more than 20%. In the promotion stage, the booking was good, and the boss was happy. AAK hydraulic cartridge counterbalance valve can stably control the opening of the valve spool without being disturbed by the load, and its stability is higher than that of its peers, because we have tricks on optimizing the structure. AAK hydraulic cartridge counterbalance valve is composed of a valve body, a valve seat, a main valve spool, a pilot valve spool and a pilot mechanism. The valve seat is connected with the valve body and forms a connected first channel. The extended end of the valve seat butts against the pilot mechanism and forms a second channel. The main valve spool is provided with a throttling slot. One end of the pilot valve spool slides and is arranged in the inner cavity of the main valve spool. The other end is connected with the pilot mechanism. The pilot valve spool is equipped with a throttling slot. The pilot valve spool is connected with the inner cavity of the main valve spool as a balanced structure.

3 Highlights of AAK Hydraulic Cartridge Counterbalance Valve, Camden gave up SUN Camden is from a hydraulic equipment company in Sweden and has been engaged in procurement for 2 years. One of their customers ordered 2 sets of customized hydraulic power units, and specially reminded that the working environment of the equipment is 20 â?? below zero. The hydraulic power unit is required to be durable for at least 1 year, and its stability should be the first. Their engineer suggested purchasing SUN hydraulic cartridge counterbalance valves, but the parameters of SUN standard parts could not fully meet the requirements of equipment working conditions, and there is no enough quantity and time to customize SUN hydraulic cartridge counterbalance valves. Camden contacted a local manufacturer of hydraulic cartridge counterbalance valves, and the manufacturer was willing and confident to sample. 3 months later, the customer complained that the equipment was not stable enough, but it was barely usable. 6 months later, the equipment went on strike. During after sales service checking, it was found that the control of the hydraulic cartridge counterbalance valve was abnormal. The original manufacturer was surprised and confused. After disassembling the hydraulic cartridge counterbalance valve, it was found that the installation torque was too large, which could easily cause the valve to jam, and there were also abnormal seals, the original manufacturer had to surrender. Camden tried to find a new manufacturer of hydraulic cartridge counterbalance valve. After a week, it was fruitless. The boss blamed Camden for poor procurement. Camden noticed AAK at Google and found that AAK Hydraulic Valve is SUN's supplier of hydraulic components for 5 consecutive years. He left a message: SUN is unwilling to sample a hydraulic cartridge counterbalance valve, and AAK is able to do a good job? The hydraulic cartridge counterbalance valve shall be durable for not less than 1 year, and its stability shall be guaranteed. I have judged that he is in trouble when purchasing hydraulic cartridge counterbalance valves. According to the hydraulic schematic diagram of the system, hydraulic cartridge counterbalance valve drawings, equipment working condition parameters and working scenarios provided by Camden, AAK engineer found that this hydraulic cartridge counterbalance valve is similar to the hydraulic cartridge relief valves that we supplied to a Russian customer 1 year ago, which had a service life of at least 1 year under extremely cold conditions of - 55 â??. Camden was very happy to learn about the similar customer case of AAK, and requested to customize the hydraulic cartridge counterbalance valve and benchmark SUN. I said that AAK does not pursue whether this hydraulic cartridge counterbalance valve is advanced, but it must benchmark SUN in stability and reliability. At the same time, AAK needs to redesign this hydraulic cartridge counterbalance valve from 3 aspects.

At the beginning of this year, received an order from African customer for excavators with a delivery time of 2 months, which means that all accessories must be in place within 1 month, including 600 hydraulic cartridge valves. The production time for the factory is a little more than 2 weeks. The purchaser Peter sent the order information of the hydraulic cartridge valve to all the hydraulic valve manufacturers he contacted before at the first time. More than 20 hydraulic valve manufacturers said that they could not complete the order of the hydraulic cartridge valve in such a short time, and it would take at least 3 - 4 weeks. His supervisor was not satisfied with this delivery time and asked him to find a new hydraulic valve manufacturer. After the email was sent, there was basically no sound. Peter was very helpless and worried. Peter asked Mark for help. HYDRAULIC VALVE to ask if could produce 600 hydraulic cartridge valves in 2 weeks and CC Peter, and joking at the end of the email that if HYDRAULIC VALVE could not complete the hydraulic cartridge valve order, then there is no need to waste time on looking for a new hydraulic valve manufacturer. According to the drawings they sent, technical department found that this was very close to the hydraulic cartridge valve supplied to a Russian customer last year, so the time in the early stage of the production of the hydraulic cartridge valve was saved. After the price of the hydraulic cartridge valve was approved, the process data could be configured on the computer on the same day and the production could be carried out the next day. 2 weeks later, 600 hydraulic cartridge valves were delivered on time, which was the first of all the accessories purchased by Peter to arrive at the company's warehouse. Peter didn't expect that the hydraulic cartridge valve he was most worried about was the first to be completed. Peter appreciated the advice from Mark and was also surprised that could complete this in 2 weeks, while his previous hydraulic valve suppliers needed 3-4 weeks. Mark told : 1. is his most trusted hydraulic valve manufacturer. can surprise him every time when the hydraulic valve order is urgent. 2. has a large amount of data storage and clear classification. For hydraulic valves with relevant data, they can use the most advanced UG / SOLIDWORK software and finite element analysis method to configure process data in 2 hours, which is 3-6 times faster than that of other suppliers. 3. is equipped with advanced machine tools imported from Swiss, coupled with their own modified fixtures, the production speed is accelerated and man-made errors are avoided at the same time. After listening to the introduction realized that only a good hydraulic valve supplier can make his purchasing smooth. successfully completed this urgent order.

Supplier: Micro silica (silica fume), silica, fly ash, pozzolano, ggbfs and white cement, other cementatious materials and factory/plants specialized spare parts & equipments, automation & switchgear, drives & transmission spares, instrumentation & pump, pneumatic & hydraulic spares, valves & actuators, mechanical parts, high carbon ferro chrome, foundry pig iron, iron ore concentrate, chromite ore, antimony ore, silicon metal 441 (powder), ferro silicon (fesi), iron ore pellet, copper concentrate

For Hydraulic Counterbalance Valve benchmarking HAWE, it is difficult for AAK to find rivals in the field of high pressure resistance Santiago is from Spain. He has been a purchaser of the company for 3 years. His boss trusts him very much. Unexpectedly, a hydraulic counterbalance valve overturned him. In the second half of last year, one of their hydraulic cylinders was complained by the customer because of shaking. The engineer judged that the hydraulic counterbalance valve used was abnormal, but the reason was unknown. After receiving the defective hydraulic counterbalance valve, the original manufacturer found that the internal pressure spring had failed, resulting in the slow response of the hydraulic counterbalance valve. This is the best pressure spring of the original manufacturer, but it still could not withstand the impact of 450bar high pressure and high frequency. Santiago had to change the manufacturer of the hydraulic counterbalance valve. After more than a week, no manufacturer was able to guarantee that the valve would not fail under the high pressure of 450bar for more than 1 year. It had been nearly 2 weeks, and there was no solution to customer complaints. Santiago was under great pressure. Santiago accidentally found AAK Hydraulic Valve in Google. He left a message on the AAK website asking whether the pressure spring of the hydraulic counterbalance valve would not fail for more than 1 year under the high pressure and high frequency working condition of 450bar? According to his drawings and working conditions, I told him that if the German HAWE was used, it would be 100% OK, but the quantity was too small, and HAWE would not necessarily accept it, and the cost was not low. AAK has a similar hydraulic counterbalance valve. Let's see if it can be a substitute first? 3 weeks later, Santiago informed that the AAK hydraulic counterbalance valve could be installed with their hydraulic cylinder and operated normally. But he seemed worried that it would not last long. I told him that Germany HAWE is the first brand of hydraulic valves in the subdivision field of high pressure resistance. The function of AAK hydraulic counterbalance valve benchmarks HAWE, which has been shipped for many times. The fact has proved that there is no repair report for 1 year, and the pressure spring can not lose efficacy for more than 1 year. Why dare I say so? The pressure spring of AAK hydraulic counterbalance valve is made of 60Si2CrVA alloy steel. At the same time, in combination with special heat treatment process, 60Si2CrVA pressure spring steel is heated to 860 �° c, kept for 20-40 min for austenitizing, and then subjected to short-term high-temperature water cooling quenching to room temperature. The comprehensive properties of the treated 60Si2CrVA spring steel have been improved by at least 2 times, especially the strength and toughness of the pressure spring, which quality far exceeds most springs.

The 1 million times durability of hydraulic counterbalance valves, AAK quality benchmarked with SUN hydraulics, but the price was 30% cheaper Last week, the German customer Thorsten sent an order for 1,200 hydraulic counterbalance valves, and said that only AAK and SUN hydraulic counterbalance valves passed 1 million durability tests among the 6 hydraulic valve manufacturers making the samples. However, the price of AAK was 30% lower than that of SUN, and the delivery time was faster. In May this year, Thorsten's company received an order for a batch of special hydraulic winches. The customer requested that the equipment be guaranteed for at least 1 year of service life. The engineer required that the durability test of the hydraulic counterbalance valve to be purchased by Thorsten must reach more than 1 million times. Thorsten found a local hydraulic counterbalance valve manufacturer to carry out the test. After 100,000 times, the O-ring wear affected the seal. After the sealing ring was replaced, the valve spool and valve body were worn and leaked again after 200,000 times, and the local manufacturer surrendered. Thorsten had to find a manufacturer of hydraulic counterbalance valves with higher durability. In order to avoid wasting purchasing time again, the two schemes were carried out simultaneously. One is to purchase the original SUN hydraulic counterbalance valves, and the other is to find a factory for customized hydraulic cartridge valves. When Thorsten contacted AAK, I told him that the requirement of hydraulic counterbalance valves for 1 million times was not very high. How could local hydraulic valve manufacturer fail? Thorsten said that when testing this hydraulic counterbalance valve, the opening and closing cycle time is set to 5 seconds, the set pressure is 21 PMa, and the flow rate is 9L/min. The wear resistance of the sealing ring, valve spool and valve body is at least 50% higher than that of the conventional hydraulic counterbalance valves. This time, including AAK, there are 6 hydraulic valve manufacturers to make samples. More than a month later, Thorsten said that among the 6 hydraulic counterbalance valve manufacturers, only AAK and SUN hydraulic counterbalance valves have passed the durability test for 1 million times, but the price of AAK is 30% lower than that of SUN. At the same time, AAK can provide a delivery time 4 weeks faster than that of sun. Thorsten especially wants to know why AAK is so strong. AAK hydraulic counterbalance valves are different from peers due to the following 3 points: 1. AAK adopts Japanese special polyurethane rubber sealing ring for this hydraulic counterbalance valve. Under the special working condition required by Thorsten, the durability limit of rubber sealing ring is about 100,000 times only, while the wear-resistant and high-pressure resistance performance of ours is more than twice that of other rubber sealing rings.

AAK customized hydraulic counterbalance valve replaced SUN, making Nancy win double the year-end bonus Nancy comes from a hydraulic equipment company in the United States. In October last year, they developed a hydraulic power unit that used a hydraulic counterbalance valve. Nancy purchased the standard parts of SUN hydraulics counterbalance valve according to the model required by the engineer. During the commissioning of the hydraulic power unit, the oil cylinder shook and made abnormal noise shortly after the equipment was started. After checking the design principle and installation method, the engineer judged that the problem probably lied in the hydraulic counterbalance valve. They asked to replace it with a new hydraulic counterbalance valve, but SUN after-sales personnel said that there would be no problem with the SUN hydraulic counterbalance valve and were unwilling to replace it. The engineer tested the hydraulic counterbalance valve separately, and the parameters were also normal. The technical team was confused. The promotion date of the new equipment was coming, but the machine test was stuck now, and the boss was also very anxious. Nancy tried to consult with different hydraulic counterbalance valve manufacturers, but after a week, there was no progress. She found AAK on Google and left a message to us: After using SUN hydraulic counterbalance valve, the equipment commissioning was abnormal, but no abnormality was found in the separate test of hydraulic counterbalance valve. At first glance, there seems to be no solution. Our engineer suggested Nancy to provide working condition requirements, hydraulic schematic diagram and equipment abnormal video. After discussion, AAK technical team judged that there was a problem with the flow selection of the hydraulic counterbalance valve. I told her that the flow difference of the cylinder diameter ratio of their power unit was 2.3 : 1. Although this ratio could be used for the standard parts of SUN hydraulic counterbalance valve, its stability was difficult to be guaranteed. This was the reason why the oil cylinder vibrated and made abnormal noise during the test run. Their engineers also recognized the reasoning of AAK technical team and asked AAK to customize standard two-way hydraulic counterbalance valves with appropriate flow. 45 days later, AAK sent 20 hydraulic counterbalance valves for test order. 2 weeks later, Nancy informed by email that the test run was successful with AAK hydraulic counterbalance valves, and the oil cylinder jitter and abnormal noise were disappeared, which could also catch up with the promotion of the equipment. Purchased a hydraulic counterbalance valve with unsuitable flow, no one in the company could solve the problem. It was solved by using AAK non-standard customized hydraulic counterbalance valves.

Bill is a purchaser of Manitowoc company in the United States. Two years ago, AAK received an inquiry about hydraulic counterbalance valves from him, and there were few contacts later. Unexpectedly, two years later, we received an email from him consulting about the problems of the hydraulic counterbalance valves. After communication, we learned that a batch of hydraulic counterbalance valves he purchased elsewhere had problems and almost got into a big trouble. Last summer, a crane shipped by their company, the crane winch system lost control during construction and the hook slipped off. Fortunately, there was no one under the hook at that time, otherwise there would be great trouble. According to the analysis of the field engineer, it is considered that the hydraulic counterbalance valve used in the crane winch system is abnormal. After disassembling the hydraulic counterbalance valve, it is found that there is a deviation in the concentricity between the valve spool and the valve seat. The valve spool is affected by large eccentric hydraulic force, so that the hydraulic counterbalance valve lost its function of balance and the hook slipped off. After knowing the reason, Bill contacted the original hydraulic counterbalance valve supplier. The supplier replied that the hydraulic counterbalance valves were indeed within the warranty period, he can replace the abnormal hydraulic counterbalance valves with a new ones, but can not guarantee that each hydraulic counterbalance valve had the same concentricity and could be used for more than 1 year. Bill was worried about the stability of the new hydraulic counterbalance valves. He didn't want to have big trouble and had to find a new hydraulic counterbalance valve manufacturer. In crane hydraulic system, the performance of hydraulic counterbalance valve is the cornerstone of winch system, and the consistency of hydraulic counterbalance valve concentricity is the key. Bill also asked other hydraulic counterbalance valve manufacturers. No factory guarantees that the concentricity of the hydraulic counterbalance valve can be still consistent after 1 year of use. Bill wants to know how about the concentricity of AAK hydraulic counterbalance valves after being used for 1 year. We told Bill that perhaps having a try is the best answer. He can detect the concentricity of AAK hydraulic counterbalance valves in an all-round way. After 15 days, we sent 4 samples of hydraulic counterbalance valves according to his drawings. Seven days later, Bill informed us that the concentricity test data of AAK hydraulic counterbalance valves were indeed more comprehensive than that of his original manufacturer. How to ensure that the concentricity of AAK hydraulic counterbalance valves is still consistent after 1 year of use? For some manufacturers, when processing the components of hydraulic counterbalance valves, there are discrepancies between the specification parameters and design,

Andy is our old hydraulic valve customer in the The hydraulic cartridge valves he purchased from in previous years always has a standard of machining surface roughness around 0.8m. In last year, Andy sent an email to inform us that in the future, the machining surface accuracy of their hydraulic cartridge valves will be improved to within 0.3m. engineers believe that based on the current equipment system, it is very difficult to improve the machining surface accuracy of hydraulic cartridge valves to 0.3 m. It is also very difficult to find such a hydraulic cartridge valve manufacturer I know that has only two options, either give up the business of his hydraulic cartridge valves or accept his accuracy standard. This is the first time I have faced the choice of "standing in line" since I joined the hydraulic valve industry. The cooperation with Andy has always been trustworthy, pleasant and efficient. doesn't want to give up such customers. After two rounds of communication internally, technical team has not reached a consensus. I have to call my retired master and hope to hear his opinions. My master told me that this is a rare opportunity to catch up with and surpass the accuracy of international hydraulic cartridge valves. The roughness of the working surface under 0.3m is rare in , but some European hydraulic cartridge valve manufacturers have this strength. must first start with the equipment, and then select the most experienced operators from the factory for special aircraft training, so as to have the opportunity to compete with those top European hydraulic cartridge valve manufacturers. American HARDINGE precision CNC lathe is worthy of a try. At present, none of the domestic hydraulic cartridge valve manufacturers have this equipment. After contacting the equipment manufacturer, technical team took the hydraulic cartridge valves produced for Andy before to the equipment factory, and asked the engineer of the equipment manufacturer to go directly to the machine for proofing. A week later, we sent the hydraulic cartridge valve samples to Andy and asked them to test the accuracy parameters. Two weeks later, Andy informed that the previous hydraulic cartridge valve accuracy test was completed twice. This time, hydraulic cartridge valve was tested 4 times, and the accuracy fully met the standard. At the same time, he told me that after receiving the accuracy improvement notice, the other 3 domestic hydraulic cartridge valve manufacturers directly gave up, and only dared to test the sample and succeeded in one test. He was very surprised. The machine tool to be introduced by has advantages in accuracy. The parameters of the machine tool: spindle speed up to 6000r/ min, spindle radial run out 0.0008mm, positioning accuracy (X/Z)